Facile Synthesis of Hollow In2O3 Microspheres and Their Gas Sensing Performances

Xiaolong Hu,Xin Zhou,Biao Wang,Peng Sun,Xiaowei Li,Chen Wang,Jiangyang Liu,Geyu Lu

DOI: https://doi.org/10.1039/c4ra12244e

IF: 4.036

2015-01-01

RSC Advances

Abstract:Hollow In2O3 microspheres were synthesized by a facile solvothermal method, and exhibited excellent sensing properties at low operating temperatures.

What problem does this paper attempt to address?

In(OH)3particles from an Ionic Liquid Precursor and Their Conversion to Porous In2O3particles for Enhanced Gas Sensing Properties

Zhonghao Li,Yang Li,Yuxia Luan,Junchao Li,Aixin Song

DOI: https://doi.org/10.1039/c2ce26733k

IF: 3.756

2013-01-01

CrystEngComm

Abstract:The ionic liquid precursor tetrabutylammonium hydroxide (TBAH) is used to synthesize In(OH)3 particles. The ionic liquid TBAH is demonstrated to be effective for the synthesis of In(OH)3 nanorods with a controlled size. The effect of the indium salt and the added water amount on the final products is investigated. The synthesized In(OH)3 nanorods could be further transformed into porous In2O3 rod particles. Specifically, the gas sensing properties of the synthesized porous In2O3 rod particles to various organic compounds (methanol, ethanol, isopropanol, butanol, ethyl acetate and toluene) exhibit remarkable sensitivities, low detection limits and fast response–recovery times, which are superior to the reported In2O3 based sensors. The as-prepared porous In2O3 rod-based sensors thus demonstrate their potential applications in detecting chemical contaminants and dangerous gases.
Hydrothermal Synthesis of Novel In(2)O(3) Microspheres for Gas Sensors.

Hao Jiang,Junqing Hu,Feng Gu,Wei Shao,Chunzhong Li

DOI: https://doi.org/10.1039/b904408f

IF: 4.9

2009-01-01

Chemical Communications

Abstract:Novel In(2)O(3) hollow microspheres were successfully prepared by a hydrothermal then annealing process; the microspheres exhibited a quick response to dilute ethanol and quick recovery.
In2O3 Hollow Microspheres: Synthesis from Designed In(OH)3 Precursors and Applications in Gas Sensors and Photocatalysis

Benxia Li,Yi Xie,Meng Jing,Guoxin Rong,Yecang Tang,Guangzhao Zhang

DOI: https://doi.org/10.1021/la061844k

IF: 3.9

2006-01-01

Langmuir

Abstract:In this work, well-shaped In(OH)(3) hollow microspheres have been successfully prepared via a novel surfactant-free vesicle-template-interface route in the "formamide-resorcinol-water" system, in which spontaneous vesicles were formed under hydrothermal conditions and NH3 from the hydrolysis of formamide acted as the OH-provider. Morphological and structural characterizations indicate that the shells of as-prepared In(OH)(3) hollow microspheres were constructed by numerous nanocubes about 80 nm in size. As desired, In2O3 hollow microspheres were obtained from annealing the designed In(OH)(3) precursors, and the as-obtained In2O3 hollow microspheres performed well as a gas-sensing material in response to both ethanol and formaldehyde gases and as a photocatalyst for photocatalytic degradation of rhodamine B. The facile preparation method and the improved properties derived from special microstructures are significant in the synthesis and future applications of functional nanomaterials.
Preparation and Gas Sensing Properties of Hierarchical Flower-Like In2O3 Microspheres

Xiumei Xu,Peilu Zhao,Dawei Wang,Peng Sun,Lu You,Yanfeng Sun,Xishuang Liang,Fengmin Liu,Hong Chen,Geyu Lu

DOI: https://doi.org/10.1016/j.snb.2012.10.091

2013-01-01

Abstract:In this work, flower-like In2O3 hierarchical microspheres were successfully synthesized by a facile hydrothermal then sinter process with the help of surfactant sodium dodecyl sulfonate. The as-synthesized samples were characterized using X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). The results revealed that In2O3 microspheres are built from nanosheets. These sheets, analogous to a chrysanthemum, are aligned to the spherical surface, pointing toward a common center. The sensing performance of the as-obtained In2O3 for NO2 was evaluated at 150°C. The results revealed that the novel In2O3 exhibited good gas-sensing properties, indicating its practical potential for detecting NO2 of ppb levels.
Facile Synthesis of In2O3 Nanoparticles for Sensing Properties at Low Detection Temperature

Bingxin Xiao,Fei Wang,Chengbo Zhai,Pan Wang,Chuanhai Xiao,Mingzhe Zhang

DOI: https://doi.org/10.1016/j.snb.2016.05.082

IF: 9.221

2016-01-01

Sensors and Actuators B Chemical

Abstract:In2O3 nanoparticles are successfully prepared via a facile solvothermal method without any templates or surfactants at a rather low temperature (100 degrees C). The results of various physical characterizations revealed that the solvothermal precursor is irregular-shaped and the as -prepared In2O3 samples are constructed from uniform nanoparticles with unique diameter (20-30 nm) after calcining. Time-dependent experiment was carried out to understand morphology evolution during the calcining process. The In2O3 nanoparticles as novel gas sensors exhibit fast and high response as well as good selectivity toward NO2 gas at ppb level at a rather low operating temperature (60 degrees C). The sensing process is tentatively explained in terms of the adsorption-desorption mechanism and chemical kinetics theories. (C) 2016 Elsevier B.V. All rights reserved.
Facile synthesis and gas sensing properties of In(OH)3 and In2O3 microcubes

Jijiang Liu,Gang Chen,Yaoguang Yu,Yalin Wu,Mingjun Zhou

2013-01-01

Abstract:In(OH)3 microcubes were synthesized with a hydrothermal process at a certain pH value without any surfactant and organic agents. By annealing as-prepared In(OH)3 precursors at 400°C in air, we obtained In2O3 microcube that inherited the morphologies of their precursors. The resulting In2O3 still slightly distorted due to the dehydration process of In(OH)3. The phase compositions, morphologies and thermal properties of the synthesized samples were characterized by powder X-ray diffraction, scanning electron microscopy and thermogravimetric analysis. The gas sensing performance of In2O3 microcubes toward H2, CO, CH4, C2H5OH, CO2 was evaluated at optimal working temperature of 275°C. The results revealed that the In2O3 nanocubes exhibited excellent gas-sensing properties for C2H5OH. The sensing mechanism of the In2O3 microcube sensors was discussed. These uniform microcubes may also be useful in microelectronic and optoelectronic devices.
Hierarchical hollow microsphere and flower-like indium oxide: Controllable synthesis and application as H 2S cataluminescence sensing materials

Pingyang Cai,Wei Bai,Lichun Zhang,Hongjie Song,Yingying Su,Yi Lv

DOI: https://doi.org/10.1016/j.materresbull.2012.06.002

IF: 5.6

2012-01-01

Materials Research Bulletin

Abstract:In the present work, In2O3 hierarchical hollow microsphere and flower-like microstructure were achieved controllably by a hydrothermal process in the sodium dodecyl sulfate (SDS)-N,N-dimethyl-formamide (DMF) system. XRD, SEM, HRTEM and N2 adsorption measurements were used to characterize the as-prepared indium oxide materials and the possible mechanism for the microstructures formation was briefly discussed. The cataluminescence gas sensor based on the as-prepared In2O3 was utilized to detect H2S concentrations in flowing air. Comparative gas sensing results revealed that the sensor based on hierarchical hollow microsphere exhibited much higher sensing sensitivity in detecting H2S gas than the sensor based on flower-like microstructure. The present gas sensor had a fast response time of 5s and a recovery time of less than 25s, furthermore, the cataluminescence intensity vs. H2S concentration was linear in range of 2–20μgmL−1 with a detection limit of 0.5μgmL−1. The present highly sensitive, fast-responding, and low-cost In2O3-based gas sensor for H2S would have many practical applications.
One-step Synthesis and Gas Sensing Characteristics of Urchin-Like In2O3

Xiumei Xu,Xiaodong Mei,Peilu Zhao,Peng Sun,Yangfeng Sun,Xiaolong Hu,Geyu Lu

DOI: https://doi.org/10.1016/j.snb.2013.05.029

IF: 9.221

2013-01-01

Sensors and Actuators B Chemical

Abstract:In this work, urchin-like In2O3 microspheres were fabricated using a solvothermal method in the presence of SDS (sodium dodecyl sulfonate) and urea. The as-synthesized samples were characterized using X-ray powder diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM). The results indicate that the synthesized urchin-like In2O3 microspheres were constructed by nanorods. Moreover, the gas sensing properties of as-prepared products were investigated. It was found that the sensor based on such novel urchin-like In2O3 microspheres exhibited high response and good selectivity to O3.
Facile Synthesis and Gas Sensing Properties of In(OH)_3 and In_2O_3 Microcubes

Ji-Jiang Liu,Gang Chen,Yaoguang Yu,Yalin Wu,Mingjun Zhou

2013-01-01

Abstract:In(OH)_3 microcubes were synthesized with a hydrothermal process at a certain pH value without any surfactant and organic agents. By annealing as-prepared In(OH)_3 precursors at 400˚C in air, we obtained In_2O_3 microcube that inherited the morphologies of their precursors. The resulting In_2O_3 still slightly distorted due to the dehydration process of In(OH)_3. The phase compositions, morphologies and thermal properties of the synthesized samples were characterized by powder X-ray diffraction, scanning electron microscopy and thermo gravimetric analysis. The gas sensing performance of In_2O_3 microcubes toward H_2, CO, CH_4, C_2H_5OH, CO_2 was evaluated at optimal working temperature of 275˚C. The results revealed that the In_2O_3 nanocubes exhibited excellent gas-sensing properties for C_2H_5OH. The sensing mechanism of the In_2O_3 microcube sensors was discussed. These uniform microcubes may also be useful in microelectronic and optoelectronic devices.
Facile Synthesis of La-doped In2O3 Hollow Microspheres and Enhanced Hydrogen Sulfide Sensing Characteristics

Dongdong Wei,Wenhao Jiang,Hongyu Gao,Xiaohong Chuai,Fengmin Liu,Fangmeng Liu,Peng Sun,Xishuang Liang,Yuan Gao,Xu Yan,Geyu Lu

DOI: https://doi.org/10.1016/j.snb.2018.08.130

IF: 9.221

2018-01-01

Sensors and Actuators B Chemical

Abstract:The undoped and 1.0-5.0 mol% La-doped In2O3 hollow microspheres have been successfully synthesized via a simple hydrothermal method without template and gas sensor have been fabricated basing on them. The nanostructures and morphologies of the maintained hollow spheres were characterized by various experimental techniques. The gas sensing properties of these hollow microspheres were investigated systematically. The results indicated that among all the samples (pure, 1.0, 3.0 and 5.0 mol% La-doped In2O3), 3.0 mol% La-doped In2O3 exhibited the highest response toward 10 ppm hydrogen sulfide (H2S) at 200 degrees C, having a response value of 17.8, approximately 4.8 times higher than pure In2O3. Furthermore, excellent selectivity, good repeatability and outstanding long-term stability were also achieved. The significantly enhanced sensing properties to H2S could be attributed to the changes in distribution of different oxygen components, crystallite size and specific surface area caused by La doping.
One-step synthesis of SnO 2 hollow microspheres and its gas sensing properties

yan zhao,j liu,qi liu,yanbo sun,dalei song,wanlu yang,jun wang,lianhe liu

DOI: https://doi.org/10.1016/j.matlet.2014.08.073

IF: 3

2014-01-01

Materials Letters

Abstract:Hollow spheres of SnO2 (Tin oxide) have been successfully synthesized by using a one-step calcined method and the products were uniform after heating SnO2 crystals at 500°C for an hour, the range of diameter is from 300 to 900nm. We successfully used only one reagent (stannous octoate) without any catalyst or surfactant to synthesize SnO2 crystals, in which was fast, simple and reproducible. Gas sensors based on these SnO2 microspheres exhibited excellent selectivity, fast response, and good selectivity to 1–300ppm ethanol vapor at 320°C. It has shown great sensitivity at a low concentration (1ppm) and operating temperature pointing out that the SnO2 microsphere is an ideal potential material for ethanol sensors.
Microstructure and Gas Sensing Property of Porous Spherical In2o3 Particles Prepared by Hydrothermal Method

Jian Wang,Xueping Gan,Zhiyou Li,Kechao Zhou

DOI: https://doi.org/10.1016/j.powtec.2016.08.046

IF: 5.64

2016-01-01

Powder Technology

Abstract:Porous spherical In(OH)3 particles with controllable size were hydrothermally synthesized from aqueous In(NO3)3 solution with the help of urea and citric acid. The average size of the synthesized In(OH)3 particles decreased with the increase of the molar ratio between citric acid and In3+concentration. Cubic In2O3 phase was obtained after a hydrothermal process at 160°C and a calcination process at 600°C, while mixed rhombohedral and cubic In2O3 phases were obtained by annealing the hydrothermally synthesized precursor at 180°C. Morphology, internal structure, particle size distribution and specific surface area of the In2O3 particles were characterized. A possible mechanism was proposed to illustrate the growth of In2O3 particles. The gas sensors which prepared with porous cubic In2O3 materials displayed high sensitivity to formaldehyde.
Controlled synthesis and gas sensing properties of In2O 3 with different phases from urchin-like InOOH microspheres

Pengyuan Song,Weide Zhang

DOI: https://doi.org/10.1016/j.materresbull.2014.01.036

IF: 5.6

2014-01-01

Materials Research Bulletin

Abstract:•Preparation of nanostructured In2O3 microspheres.•Morphology and phase control of In2O3.•Gas sensors based on the In2O3 microspheres exhibit excellent sensing properties for the detection of formaldehyde.
Synthesis of Cu2O Microspheres with Hollow and Solid Morphologies and Their Gas Sensing Properties

Qi Guo,Yanqiong Li,Wen Zeng

DOI: https://doi.org/10.1016/j.physe.2019.113564

IF: 3.369

2019-01-01

Physica E Low-dimensional Systems and Nanostructures

Abstract:Cu2O microspheres with hollow and solid features were successfully prepared via a convenient liquid phase reducing method. Interestingly, we found that the discrepancy in morphology arose from a simply changing on the adding sequence of aqueous sodium dodecyl sulfate (SDS) and CuCl2 with other conditions unchanged. Based on experimental results, the feasible formation mechanisms of both morphologies were deduced, where the relative concentration of SDS and CuCl2 was a crucial factor that effect the resultant morphologies. In comparison with the solid microspheres, the hollow Cu2O exhibited superior gas sensing performance. The significant performance might ascribe to its unique hollow structure, contributing to plenty of active sites existed on both the inner and outer surface and unrestricted gas diffusion in the hollow microspheres.
Synthesis of In2O3 Hollow Microspheres for Chlorine Gas Sensing Using Yeast As Bio-Template

Jiangwei Ma,Huiqing Fan,Nan Zhao,Weiming Zhang,Xiaohu Ren,Chao Wang,Yun Wen,Weijia Wang

DOI: https://doi.org/10.1016/j.ceramint.2019.01.268

IF: 5.532

2019-01-01

Ceramics International

Abstract:In2O3 hollow microspheres (HMs) were synthesized by a facile route with low-cost yeast as a bio-template. The prepared In2O3 HMs maintained the morphology of the yeast, which was uniform ellipsoids with an average length of 2 mu m. Gas sensing measurements showed that the obtained In2O3 HMs have excellent selectivity for chlorine (Cl-2). Furthermore, the possible formation and gas sensing mechanisms of the In2O3 HMs have been proposed.
Facile synthesis of single-crystalline hollow alpha-Fe2O3 nanospheres with gas sensing properties

Pei-Pei Wang,Xiaoxin Zou,Liang-Liang Feng,Jun Zhao,Pan-Pan Jin,Rui-Fei Xuan,Ye Tian,Guo-Dong Li,Yong-Cun Zou

DOI: https://doi.org/10.1039/c4ra05651e

IF: 4.036

2014-01-01

RSC Advances

Abstract:High-quality single-crystalline hollow alpha-Fe2O3 nanospheres were prepared, using the ZnS-CHA (CHA = cyclohexylamine) nanohybrid as an additive through a solvothermal reaction, which avoids tedious steps and a high temperature calcination process. The formation process of these hollow nanospheres can be divided into two stages: (i) formation of solid Fe2O3 nanospheres and (ii) preferential inside-out dissolution of the solid nanoparticles to form hollow nanospheres. Due to the unique single-crystalline hollow structure, the as-obtained alpha-Fe2O3 nanomaterial exhibits enhanced gas sensing properties.
Zn-doped In2O3 hollow spheres: mild solution reaction synthesis and enhanced Cl2 sensing performance

pei li,huiqing fan,yu cai,mengmeng xu

DOI: https://doi.org/10.1039/c3ce42325e

IF: 3.756

2014-01-01

CrystEngComm

Abstract:Zn-doped In2O3 hollow spheres have been prepared by a facile chemical route under a low temperature of 80 degrees C without any surfactant or template. The morphological features were characterized as self-assembled hollow spheres with a diameter of 200-300 nm, and it was observed that the amount of doped Zn significantly affects the overall morphology. Furthermore, analysis of the N-2 adsorption-desorption tests showed that the Zn-doped In2O3 hollow spheres (the molar ratio of In : Zn is 9 : 1) adsorbed the largest amount of N-2 and had the biggest specific surface area (26.4 m(2) g(-1)), which contributed to the improvement of the gas sensing characteristics. Finally, the gas sensing characteristics of the obtained products were studied. The results demonstrated that the sensors based on the Zn-doped In2O3 structures exhibited a higher response to Cl-2 than those without Zn and the In : Zn = 9 : 1 (molar ratio) sample showed the highest response. The sensor based on the Zn-doped In2O3 hollow spheres (the molar ratio of In : Zn is 9 : 1) exhibited the highest response of 94.7 +/- 8.6 for 5 ppm Cl-2. The high response, quick response-recovery behaviour and excellent stability imply good potential for practical applications. The formation mechanism and gas sensing mechanism were studied.
Facile synthesis of nanoparticle packed In2O3 nanospheres for highly sensitive NO2 sensing

Bingxin Xiao,Qi Zhao,Dongxue Wang,Guangsi Ma,Mingzhe Zhang

DOI: https://doi.org/10.1039/c7nj00647k

IF: 3.3

2017-01-01

New Journal of Chemistry

Abstract:Nanoparticle packed In2O3 nanospheres are successfully synthesized via a facile one-step solvothermal method followed by annealing. The structure and morphology of the as-synthesized samples are characterized via X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). Moreover, the NO2 gas sensing properties of the nanoparticle packed In2O3 nanospheres are further investigated. The sensor shows excellent selectivity, high response (217.5 to 500 ppb), superior stability and repeatability at the optimum operating temperature of 120 degrees C with a limit of detection lower than 10 ppb. Thus, this type of material is promising for low concentration NO2 gas-sensing.
A Novel Approach for Fabricating NiO Hollow Spheres for Gas Sensors

Chengwei Kuang,Wen Zeng,Hong Ye,Yanqiong Li

DOI: https://doi.org/10.1016/j.physe.2017.12.006

IF: 3.369

2017-01-01

Physica E Low-dimensional Systems and Nanostructures

Abstract:Hollow spheres are usually fabricated by hard template methods or soft template methods with soft surfactants, which is quiet tedious and time-consuming. In this paper, NiO hollow spheres with fluffy surface were successfully synthesized by a facile hydrothermal method and subsequent calcination, where bubbles acted as the template. NiO hollow spheres exhibited excellent gas sensing performances, which results from its hollow structure and high specific surface area. In addition, a possible evolution mechanism of NiO hollow spheres was proposed based on experimental results.
Facile Synthesis of In2O3 Nanospheres with Excellent Sensitivity to Trace Explosive Nitro-Compounds

Yang-Yang He,Xu Zhao,Yang Cao,Xiao-Xin Zou,Guo-Dong Li

DOI: https://doi.org/10.1016/j.snb.2016.01.042

IF: 9.221

2016-01-01

Sensors and Actuators B Chemical

Abstract:In2O3 nanospheres with excellent sensing ability to explosive nitro-compounds have been successfully synthesized via a two-step method including a mild solvothermal process and calcination at elevated temperature in air. The as-synthesized In2O3 nanospheres are of 200–300nm in diameter and are composed of small nanoparticles with a size of around 5nm. The structure, morphology and thermal stability are investigated by XRD, SEM, TEM, HRTEM, TG and XPS. At 140°C, the responses of this sensor toward 100ppm nitromethane, nitroethane and nitropropane are 163, 220 and 375, respectively. And what’s more, the sensor also exhibits short response time of less than 1s, good long-term stability, and low detection limits. The good sensing performance should be attributed to the strong electron-withdrawing effect of nitro group and low working temperature.

Facile Synthesis of Hollow In2O3 Microspheres and Their Gas Sensing Performances

In(OH)3particles from an Ionic Liquid Precursor and Their Conversion to Porous In2O3particles for Enhanced Gas Sensing Properties

Hydrothermal Synthesis of Novel In(2)O(3) Microspheres for Gas Sensors.

In2O3 Hollow Microspheres: Synthesis from Designed In(OH)3 Precursors and Applications in Gas Sensors and Photocatalysis

Preparation and Gas Sensing Properties of Hierarchical Flower-Like In2O3 Microspheres

Facile Synthesis of In2O3 Nanoparticles for Sensing Properties at Low Detection Temperature

Facile synthesis and gas sensing properties of In(OH)3 and In2O3 microcubes

Hierarchical hollow microsphere and flower-like indium oxide: Controllable synthesis and application as H 2S cataluminescence sensing materials

One-step Synthesis and Gas Sensing Characteristics of Urchin-Like In2O3

Facile Synthesis and Gas Sensing Properties of In(OH)_3 and In_2O_3 Microcubes

Facile Synthesis of La-doped In2O3 Hollow Microspheres and Enhanced Hydrogen Sulfide Sensing Characteristics

One-step synthesis of SnO 2 hollow microspheres and its gas sensing properties

Microstructure and Gas Sensing Property of Porous Spherical In2o3 Particles Prepared by Hydrothermal Method

Controlled synthesis and gas sensing properties of In2O 3 with different phases from urchin-like InOOH microspheres

Synthesis of Cu2O Microspheres with Hollow and Solid Morphologies and Their Gas Sensing Properties

Synthesis of In2O3 Hollow Microspheres for Chlorine Gas Sensing Using Yeast As Bio-Template

Facile synthesis of single-crystalline hollow alpha-Fe2O3 nanospheres with gas sensing properties

Zn-doped In2O3 hollow spheres: mild solution reaction synthesis and enhanced Cl2 sensing performance

Facile synthesis of nanoparticle packed In2O3 nanospheres for highly sensitive NO2 sensing

A Novel Approach for Fabricating NiO Hollow Spheres for Gas Sensors

Facile Synthesis of In2O3 Nanospheres with Excellent Sensitivity to Trace Explosive Nitro-Compounds