Abstract:The need to control the formation of weakly emitting species in polymers such as aggregates and excimers, which are normally detrimental to device performance, is illustrated for the example of the polymer poly(m-phenylenevinylene-co-2,5-dioctyloxy-p-phenylenevinylene), using the model compound, 2,5-dioctyloxy-p-distyrylbenzene as a comparison. Two different methods, namely a Horner–Emmons polycondensation in dimethylformamide (DMF) and a Wittig polycondensation in dry toluene, have been used during synthesis resulting in a polymer with a predominantly trans-vinylene backbone and a polymer with a predominantly cis-vinylene backbone, respectively. Photoluminescence and absorption spectroscopy indicate that the polymer forms aggregate species in solution with spectra that are distinctly red-shifted from those associated with the intra-chain exciton. Concentration dependent optical studies were used to probe the evolution of aggregation in solution for both polymers. The results indicate that inter-chain coupling in the predominantly cis-polymer is prominent at lower concentrations than in the case of the trans-counterpart. These results are supported by pico-second pump and probe transient absorption measurements where, in dilute solutions, the polymer in a cis-configuration exhibits highly complex excited state dynamics, whereas the polymer in a trans-configuration behaves similarly to the model compound. It is proposed therefore that the degree of backbone isomerism has a profound impact on the morphology of the polymeric solid and control over it is a route towards optimising the performance of the material in thin film form. Another method to inhibit inter-chain effects using multi walled carbon nanotubes (MWNT) as nano-spacers in the polymer solutions is proposed. By comparison to spectroscopic analysis, aggregation effects are shown to be reduced by the introduction of nanotubes. Electron microscopy and computer simulation suggest a well-defined interaction between the polymer backbone and the lattice of the nanotube.

Controlling Materials Architecture on the Nanometer-Scale: PPV Nanocomposites Via Polymerizable Lyotropic Liquid Crystals

Synthesis of Ppv Nanocomposites Using Lyotropic Liquid Crystal Monomers

Length Control of Biodegradable Fiber-Like Micelles Via Tuning Solubility: A Self-Seeding Crystallization-Driven Self-Assembly of Poly(-caprolactone)-Containing Triblock Copolymers

A Nanocomposite Structure Based on Modified MCM-48 and Polystyrene

Synthesis of Functional, Nanostructured Composites and Catalysts Using Polymerizable Lyotropic Liquid Crystals

Morphology Control of Perpendicularly Oriented Lamellar Films from Azobenzene-Containing Block Copolymers with Different Spacer Lengths

Light‐Coded Digital Crystallinity Patterns Toward Bioinspired 4D Transformation of Shape‐Memory Polymers

Controlling phase and rheological behaviours of hexagonal lyotropic liquid crystalline templates for nanostructural administration and retention

Three-Dimensional Blueprinting of Molecular Patterns in Liquid Crystalline Polymers

Controlled patterning of crystalline domains by frontal polymerization

Controlling the Optical Properties of A Conjugated Co-Polymer Through Variation of Backbone Isomerism and the Introduction of Carbon Nanotubes

Controlling Morphology of the Polymer Photoactive Layer in Photovoltaic Elements: Mesoscopic Simulation

Cooperative Liquid Crystal Photo‐Polymerization and ‐Alignment with In Situ Monitoring for Substrate Independent Patterning of Optical Anisotropy

Photopolymerization-enforced stratification in liquid crystal materials

Single-Step Synthesis of Shape-Controlled Polymeric Particles using Initiated Chemical Vapor Deposition in Liquid Crystals

Optical and morphological pattern formation of in situ created reactive polymer nanoparticles: Photopolymerization-induced phase separation and spatial reconfiguration

Lyotropic Nematic Phases of Isotropic Nanoparticles via Semiflexible Polymer Ligands

A New Approach to the Synthesis of Nanocrystal Conjugated Polymer Composites

Liquid-Crystalline Polymers: Molecular Engineering, Hierarchical Structures, and Applications

Liquid-crystalline Ordering Helps Block Copolymer Self-Assembly.

Morphological transition and transformation of 2D nanosheets by controlling the balance of π–π stacking interaction and crystalline driving forces