Relative Humidity Sensors Using Hydrogel-Coated Long Period Fiber Grating

yanbiao liao,min zhang,liwei wang,dongsheng tu,xianhui mao

DOI: https://doi.org/10.1364/ofs.2006.tue38

2006-01-01

Abstract:The hydrogel-coated Long Period Grating was investigated for monitoring the Relative Humidity(RH). The resonant wavelength shifted when RH varied from 38.9% to 100%, with a resolution of ±0.3%RH and an accuracy of ±1.0%RH.

What problem does this paper attempt to address?

Fast Detection of Humidity with a Subwavelength-Diameter Fiber Taper Coated with Gelatin Film

Lei Zhang,Fuxing Gu,Jingyi Lou,Xuefeng Yin,Limin Tong

DOI: https://doi.org/10.1364/oe.16.013349

IF: 3.8

2008-01-01

Optics Express

Abstract:A subwavelength-diameter tapered optical fiber coated with gelatin layer for fast relative humidity (RH) sensing is reported. The sensing element is composed of a 680-nm-diameter fiber taper coated with a 80-nm-thickness 8-mm-length gelatin layer, and is operated at a wavelength of 1550 nm. When exposed to moisture, the change in refractive index of the gelatin layer changes the mode field of the guided mode of the coated fiber, and converts a portion of power from guided mode to radiation mode, resulting in RH-dependent loss for optical sensing. The sensor is operated within a wide humidity range (9-94% RH) with high sensitivity and good reversibility. Measured response time is about 70 ms, which is one or two orders of magnitude faster than other types of RH sensors relying on conventional optical fibers or films.
Long-Period Grating Relative Humidity Sensor with Hydrogel Coating

Yang Liu,Liwei Wang,Min Zhang,Dongsheng Tu,Xianhui Mao,Yanbiao Liao

DOI: https://doi.org/10.1109/lpt.2007.897551

IF: 2.6

2007-01-01

IEEE Photonics Technology Letters

Abstract:The long-period grating (LPG) coated with the hydrogel was investigated for monitoring the relative humidity (RH) levels-the ratio of the amount of water vapor in the air at a specific temperature to the maximum amount that the air could hold at that temperature. The experimental results showed that the resonant wavelength of the hydrogel-coated LPG was shifted when the RH varied from 38.9% to 100%, with a linearity of 99.5% and an accuracy of +/- 2.3% RH.
Fiber Optic Relative Humidity Sensor Based On The Tilted Fiber Bragg Grating Coated With Graphene Oxide

Youqing Wang,Changyu Shen,Weimin Lou,Fengying Shentu,Chuan Zhong,Xinyong Dong,Limin Tong

DOI: https://doi.org/10.1063/1.4959092

IF: 4

2016-01-01

Applied Physics Letters

Abstract:A fiber optic relative humidity (RH) sensor based on the tilted fiber Bragg grating (TFBG) coated with graphene oxide (GO) film was presented. Amplitudes of the cladding mode resonances of the TFGB varies with the water sorption and desorption processes of the GO film, because of the strong interactions between the excited backward propagating cladding modes and the GO film. By detecting the transmission intensity changes of the cladding mode resonant dips at the wavelength of 1557 nm, the maximum sensitivity of 0.129 dB/% RH with a linear correlation coefficient of 99% under the RH range of 10-80% was obtained. The Bragg mode of TFBG can be used as power or wavelength references, since it is inherently insensitive to RH changes. In addition, the proposed humidity sensor shows a good performance in repeatability and stability. Published by AIP Publishing.
Hydrogel Coated Long Period Grating Sensor for High Relative Humidity Measurement

Xiu Juan Yu,Jin Tao Zhang,Xue Feng Chen,Sheng Chun Liu

DOI: https://doi.org/10.4028/www.scientific.net/amr.981.616

2014-01-01

Advanced Materials Research

Abstract:A very sensitive hydrogel coated long period grating (LPG) humidity sensor is developed and experimentally investigated for high relative humidity monitoring. A thin-film of PINPAM hydrogel is deposited onto the cladding of LPG by using dip-coating technique. The transmission spectrum of the coated LPG is studied at different humidity levels. For humidity levels greater than 95%, the resonant dip depth suffers a sharp linear increase with a span of 10.26 dB and the resonant wavelength suffers a redshift of 8.6nm.The proposed hydrogel coated LPG humidity sensor shows a high sensitivity of 2.86dB/%RH at high relative humidity region.
A Humidity Sensor Based on a Singlemode-Side Polished Multimode–Singlemode Optical Fibre Structure Coated with Gelatin

Xianfan Wang,Gerald Farrell,Elfed Lewis,Ke Tian,Libo Yuan,Pengfei Wang

DOI: https://doi.org/10.1109/JLT.2017.2730484

IF: 4.7

2017-01-01

Journal of Lightwave Technology

Abstract:A novel relative humidity sensor based on a singlemode-side polished multimode-singlemode fibre structure coated with gelatin material is reported. The sensing principle and fabrication method of the proposed sensor are presented. The experimental method is demonstrated to provide the optimum thickness of coating layers in order to achieve the highest sensitivity of 0.14 dB/%RH and a fast response...
Humidity Sensor Based on a Long-Period Fiber Grating Coated with Polymer Composite Film

Yunlong Wang,Yunqi Liu,Fang Zou,Chen Jiang,Chengbo Mou,Tingyun Wang

DOI: https://doi.org/10.3390/s19102263

IF: 3.9

2019-05-16

Sensors

Abstract:We demonstrate a simple and highly sensitive optical fiber relative humidity (RH) sensor based on a long-period fiber grating (LPFG) coated with polyethylene glycol (PEG)/polyvinyl alcohol (PVA) composite films. The resonance wavelength of the LPFG is sensitive to environmental humidity due to the change in effective refractive index caused by the strong surface absorption and desorption of the porous PEG/PVA coatings. The sensor is sensitive in a wide range from 50% to 95% RH, with a highest sensitivity of 2.485 nm/%RH in the range 50–75% RH. The proposed RH sensor has the advantages of compact size, good reversibility, and stability, which makes it attractive for high-humidity environments.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Research on Testing the Characteristics of Hydrogel Film by Using A Long-Period Fiber Grating

Xiujuan Yu,Min Zhang,Paul Childs,Liwei Wang,Ming Lei,Yanbiao Liao,Jian Ju,Win Jin

DOI: https://doi.org/10.1364/ao.48.002171

IF: 1.9

2009-01-01

Applied Optics

Abstract:A method for testing the physical and optical properties of hydrogel thin films is reported based on using long-period fiber gratings. For humidity levels from 50% to 70% RH, a wavelength decrease of 11.0 nm is observed, with a sensitivity of 0.6 nm/%RH. For humidity levels from 70% to 98% RH, a wavelength increase of 6.3 nm is seen, with a sensitivity of 0.2 nm/%RH. For humidity levels greater than 60% RH, the transmission loss at resonance increases rapidly, showing a high degree of sensitivity of 0.5 dB/% RH. The blueshift of the wavelength was seen to be due to a thickening of the overlay, while the redshift of wavelength is due to the contribution of the drop in refractive index of the overlay. The results match well with what is expected theoretically.
A High-Temperature Humidity Sensor Based on a Singlemode-Side Polished Multimode-Singlemode Fiber Structure

Xianfan Wang,Ke Tian,Libo Yuan,Elfed Lewis,Gerald Farrell,Pengfei Wang

DOI: https://doi.org/10.1109/JLT.2018.2815955

IF: 4.7

2018-01-01

Journal of Lightwave Technology

Abstract:A relative humidity (RH) sensor based on a simple singlemode-side polished multimode-singlemode (SSPMS) fiber hybrid structure is investigated, which is capable of working over a relatively high-temperature range, at which many RH sensors based on moisture sensitive material coatings cannot operate. The beam propagation method is used to analyze the light transmission characteristics within the si...
Highly Sensitive Humidity Sensor Based on Ultra-Long-Period Fiber Gratings with Asymmetric Refractive Index Modulation

Y. Song,T. Zhu,Y. J. Rao,Y. W. Zhao

DOI: https://doi.org/10.1117/12.821229

2008-01-01

Abstract:An Ultra-long-period fiber grating (ULPFG) with asymmetric refractive index modulation is fabricated in standard telecommunication optical fiber by using high-frequency CO2 laser pulses. A highly sensitive humidity sensor based on this grating can be realized due to its high refractive index sensitivity. The ULPFG is coated with a new nano-composite hydrogel material that has a strong water absorption capacity. This kind of hydrogel can absorb water vapor in the air substantially to make its own refractive index change, inducing the resonant peak shift of the ULPFG to realize the humidity measurement. The experimental results show that a resonant peak shift of ~30nm corresponding to a variation of the surrounding humidity in the range of 38%~96%, which is three times higher than that of the humidity sensors reported. Such a novel humidity sensor could find important applications in humidity measurement.
Enlarged-Taper Tailored Fiber Bragg Grating With Polyvinyl Alcohol Coating For Humidity Sensing

yanhong liang,guofeng yan,sailing he

DOI: https://doi.org/10.1117/12.2193414

2015-01-01

Abstract:In this paper, a novel optical fiber sensor based on an enlarged-taper tailored fiber Bragg grating (FBG) is proposed and experimentally demonstrated for the measurement of relative humidity. The enlarged-taper works as a multifunctional joint that not only excites cladding modes but also recouples the cladding modes reflected by the FBG back into the leading single mode fiber. Due to the fact that cladding modes have a strong evanescent field penetrating into the ambient medium, the intensity of the reflected cladding modes is greatly influenced by the refractive index (RI) of the ambient medium. Polyvinyl alcohol (PVA) film is plated on the fiber surface by dip-coating technique, as a humidity-to-refractive index transducer, whose RI variance from 1.49 to 1.34 when the ambient humidity increases from 20%RH to 95%RH. The relative humidity response of the sensing structure is investigated in our home-made humidity chamber with a commercial hygrometer. By monitoring the intensity of the reflected cladding modes, the RH variance can be demodulated. Experimental results show that RH sensitivity depends on the RH value, and a sensitivity up to 1.2 dB/%RH can be achieved within the RH range of 30-90%. A fast and reversible time response has also been investigated. Such a probe-type and reusable fiber-optic RH sensor is a very promising technology for biochemical sensing applications, e.g., breath analysis, chemical reaction monitoring.
Relative Humidity Measurement Based on Micro Fiber with Quantum Dot Gel Coating

Siqi Hu,Guofeng Yan,Chunzhou Wu,Sailing He

DOI: https://doi.org/10.1364/cleopr.2018.th3l.2

2018-01-01

Abstract:A optical fiber relative humidity sensor based on a microfiber with quantum dot gel coating was proposed and experimentally demonstrated. The RH Sensitivity of 37.7 /%RH was obtained with good repeatability.
High-Sensitivity and Fast-Response Humidity Sensor Based on a Simple Fiber-Tip Interferometer with Thin Agarose Gel Coating

Xingchao Ma,Fengping Zhao,Ben Xu,Chun Liu Zhao,Huifang Chen,D. N. Wang,Shangzhong Jin

DOI: https://doi.org/10.1109/jlt.2023.3289533

IF: 4.7

2023-01-01

Journal of Lightwave Technology

Abstract:A high-sensitivity and fast-response relative humidity (RH) sensor based on a fiber-tip interferometer coated with agarose gel is proposed and demonstrated. To fabricate the interferometer, focusing the femtosecond laser on the fiber core near the end face of a well cleaved single-mode fiber (SMF) for less than 0.1 second to create a tiny refractive index-modulated dot is enough, then a thin film of hydrophilic material (agarose gel) is deposited on the end facet of the SMF. Owing to a high RI sensitivity of the interferometer and a humidity-induced refractive index (RI) change in the agarose gel, the fiber-tip sensor is qualified for RH sensing. The experimental results show that the sensor is extremely sensitive to high RH, with a maximum sensitivity of −2.04 dB/%RH and 0.673 nm/%RH at 90%RH. Furthermore, it exhibits low hysteresis as demonstrated by a breath monitoring of about 60 ms ultrafast response time and 160 ms recovery time. Additionally, it also shows a good long-term stability with a small standard deviation. The prominent advantages of high sensitivity, fast response, easy fabrication and compact size (total length of about 50 μm) imply that the proposed sensor has many potential applications for static or dynamic RH sensing.
Compact fiber Fabry–Perot sensors filled with PNIPAM hydrogel for highly sensitive relative humidity measurement

Ru-Lei Xia,Juan Liu,Jiulin Shi,Xing-Dao He,Jinhui Yuan,Andrew R. Pike,Liang Chu,Qiang Wu,Bin Liu

DOI: https://doi.org/10.1016/j.measurement.2022.111781

IF: 5.6

2022-09-30

Measurement

Abstract:A fiber-optic Fabry–Perot (FP) based relative humidity (RH) sensor was proposed and experimentally investigated by using Poly(N-isopropylacrylamide) (PNIPAM) hydrogel to connect two ends of single-mode optical fiber (SMF) to formulate a PNIPAM FP cavity. The water vapor will be absorbed by the PNIPAM hydrogel, which will alter both the refractive index (RI) and dimension of the PNIPAM FP cavity, resulting in the change of output resonance intensity in the reflective spectrum. The measure RH sensitivity is 1.634 nm/%RH within RH range from 45 to 75 % with good linearity of 0.9897 and excellent repeatability. The influence of PNIPAM hydrogel concentration on the RH sensitivity has been investigated - the higher the concentration of PNIPAM hydrogel, the higher the RH sensitivity of the sensor. The developed sensor can effectively monitor human respiratory with response and recovery time of 2.29 s and 1.90 s, respectively.

engineering, multidisciplinary,instruments & instrumentation
Polymer microfiber rings for high-sensitivity optical humidity sensing.

Pan Wang,Fuxing Gu,Lei Zhang,Limin Tong

DOI: https://doi.org/10.1364/AO.50.0000G7

IF: 1.9

2011-01-01

Applied Optics

Abstract:We demonstrate microrings assembled with polyacrylamide (PAM) microfibers for high-sensitivity relative humidity (RH) sensing. When exposed to moisture, the PAM microfiber absorbs water molecules and inflates monotonically with the increasing humidity, resulting in evident spectral shifts of the resonance peaks of the microring. By measuring the spectral shifts, the microring shows sensitivity as high as 490 pm/%RH and a response time of about 120 ms, within a dynamic range from 5% to 71% RH. (C) 2011 Optical Society of America
Highly Sensitive Humidity Sensor Based on a GO/Co-MOF-74 Coated Long Period Fiber Grating

Jingci Yan,Jijun Feng,Jinman Ge,Jian Chen,Feng Wang,Caiwei Xiang,Ding Wang,Qinghua Yu,Heping Zeng

DOI: https://doi.org/10.1109/lpt.2021.3139114

IF: 2.6

2022-01-15

IEEE Photonics Technology Letters

Abstract:A humidity sensor based on graphene oxide (GO)/Co-MOF-74 coated long period fiber grating is experimentally demonstrated. The long period fiber grating is prepared by CO2 laser direct writing method, with GO/Co-MOF-74 composite humidity sensitive material coated around the grating region. Combination of GO and Co-MOF-74 with porous structure can absorb water molecules effectively and improve the sensitivity. A high humidity sensitivity of 0.204 nm/%RH can be realized in the RH range of 30-50% as well as a value of 0.16 dB/%RH in the range of 50-90%, both with a linearity of more than 0.98. The proposed highly sensitive humidity sensor also shows a good performance in the stability and repeatability.

engineering, electrical & electronic,optics,physics, applied
Miniature and high-performance optical fiber relative humidity sensor based on Fabry-Perot structure interacting with hydroxyethyl cellulose

He Yan,Dandan Sun,Zifan Hou,Guanjun Wang

DOI: https://doi.org/10.1016/j.optmat.2023.113962

IF: 3.754

2023-06-08

Optical Materials

Abstract:A miniature Fabry-Perot fiber-optic sensor is demonstrated for high-performance relative humidity (RH) detection. This sensor is constructed by fusing a single-mode fiber to a small section of capillary coating the end with a hydroxyethyl cellulose film (HEC). The effects of capillary length and hydroxyethyl cellulose concentration on the RH response are investigated to obtain the preferential condition with capillary length of 102 μm and HEC concentration of 0.03 g/ml. A testing RH sensitivity of 1.24 nm/%RH can be achieved in the range of 48%RH to 60%RH. Simultaneously, small hysteresis errors are demonstrated in the tests with increasing and decreasing RH values. The dynamic measurements reveal a response time of 1.61 s and a recovery time of 2.1 s. The high sensitivity, good stability and simple fabrication process of the sensor make it promising for practical applications of relative humidity sensors.

materials science, multidisciplinary,optics
Polyimide-coated Fiber Bragg Grating for Relative Humidity Sensing

Yao Lin,Yuan Gong,Yu Wu,Huijuan Wu

DOI: https://doi.org/10.1007/s13320-014-0218-8

IF: 2.814

2014-01-01

Photonic Sensors

Abstract:A fiber-optic humidity sensor has been fabricated by coating a moisture sensitive polymer film to the fiber Bragg grating (FBG). The Bragg wavelength of the polyimide-coated FBG changes while it is exposed to different humidity conditions due to the volume expansion of the polyimide coating. The characteristics of sensors, including sensitivity, temporal response, and hysteresis, were improved by controlling the coating thickness and the degree of imidization during the thermal curing process of the polyimide. In the relative humidity (RH) condition ranging from 11.3% RH to 97.3% RH, the sensitivity of the sensor was about 13.5 pm/% RH with measurement uncertainty of ±1.5% RH.
Bragg Grating Chemical Sensor with Hydrogel As Sensitive Element

Xiaomei Liu,Shilie Zheng,Xianmin Zhang,Jun Cong,Kangsheng Chen,Jian Xu

IF: 2.56

2004-01-01

Chinese Optics Letters

Abstract:A novel fiber Bragg grating (FBG) based chemical sensor using hydrogel, a swellable polymer, as sensitive element is demonstrated. The sensing mechanism relies on the shift of Bragg wavelength due to the stress resulted from volume change of sensitive swellable hydrogel responding to the change of external environment. A polyacrylamide hydrogel fiber grating chemical sensor is made, and the experiments on its sensitivity to the salinity are performed. The sensitivity is low due to the less stress from the shrinking or swelling of hydrogels. Reducing the cross diameter of the grating through etching with hydrofluoric acid can greatly improve the sensitivity of the sensor.
High Sensitivity Relative Humidity Sensor Based on SMTF Structure Coated with Gelatin

Jiachen Guo,Jia Bo,Huang Tang,Dong Zhao,Pengwei Zhou,Jian Wang

DOI: https://doi.org/10.1002/mop.32471

IF: 1.311

2020-01-01

Microwave and Optical Technology Letters

Abstract:A high sensitivity relative humidity sensor based on single mode tapered fiber (SMTF) structure coated with gelatin is reported. The sensing element is composed of a 12-mu m-diameter fiber taper coated with a thickness of 26-mm-length gelatin layer, and is operated at a wavelength of 1550 nm. The sensor is designed based on the intermodal interference effect with high sensitivity (511.33 nW/%RH) and linear response for high RH (72-90%RH) at 25 degrees C. In this study, we analyzed the factors affecting sensor sensitivity and proposed the method to improve the sensitivity of the sensor. The sensor responses obviously. When the RH increased to more than 70%, the optical power boosts almost 10 000 times, which has promising potential applications as an optical switch in industrial production, food processing, and environmental early warning.
Highly Sensitive Fiber Relative Humidity Sensor Based on Tip Michelson Interferometer With Agarose Gel Coating

Ben Xu,Yun Guo,Xingchao Ma,Yingfang Zhang,Chun-Liu Zhao,D. N. Wang

DOI: https://doi.org/10.1109/JSEN.2022.3224238

IF: 4.3

2023-01-01

IEEE Sensors Journal

Abstract:A tip Michelson interferometer (MI) is proposed and experimentally demonstrated for relative humidity (RH) sensing. The device consists of a short capillary tube with a small inner diameter that is spliced to a single-mode fiber (SMF) and coated with agarose gel on its end face, and the solid capillary wall and gel act as the sensing arm of the MI. When the agarose gel absorbs water modules, its refractive index (RI) and volume vary, resulting in the shift of the reflection spectrum of the MI. The relationship between the structural parameters and the performance of the device is revealed after performing theoretical analysis and experimental verification, which provides guidance for optimizing the device. The maximum sensitivity of 0.752 nm/% RH with a linear correlation coefficient of (Adjusted <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${R}^{{2}}) 0.9927$ </tex-math></inline-formula> within the range of 25%–90% RH is obtained. Moreover, the proposed sensor exhibits good performances of robustness, compact size, high repeatability, fast response (< 100 ms), and small measurement uncertainty (< 0.21% RH), which makes the sensor promising for accurately static or dynamic moisture measuring.

Relative Humidity Sensors Using Hydrogel-Coated Long Period Fiber Grating

Fast Detection of Humidity with a Subwavelength-Diameter Fiber Taper Coated with Gelatin Film

Long-Period Grating Relative Humidity Sensor with Hydrogel Coating

Fiber Optic Relative Humidity Sensor Based On The Tilted Fiber Bragg Grating Coated With Graphene Oxide

Hydrogel Coated Long Period Grating Sensor for High Relative Humidity Measurement

A Humidity Sensor Based on a Singlemode-Side Polished Multimode–Singlemode Optical Fibre Structure Coated with Gelatin

Humidity Sensor Based on a Long-Period Fiber Grating Coated with Polymer Composite Film

Research on Testing the Characteristics of Hydrogel Film by Using A Long-Period Fiber Grating

A High-Temperature Humidity Sensor Based on a Singlemode-Side Polished Multimode-Singlemode Fiber Structure

Highly Sensitive Humidity Sensor Based on Ultra-Long-Period Fiber Gratings with Asymmetric Refractive Index Modulation

Enlarged-Taper Tailored Fiber Bragg Grating With Polyvinyl Alcohol Coating For Humidity Sensing

Relative Humidity Measurement Based on Micro Fiber with Quantum Dot Gel Coating

High-Sensitivity and Fast-Response Humidity Sensor Based on a Simple Fiber-Tip Interferometer with Thin Agarose Gel Coating

Compact fiber Fabry–Perot sensors filled with PNIPAM hydrogel for highly sensitive relative humidity measurement

Polymer microfiber rings for high-sensitivity optical humidity sensing.

Highly Sensitive Humidity Sensor Based on a GO/Co-MOF-74 Coated Long Period Fiber Grating

Miniature and high-performance optical fiber relative humidity sensor based on Fabry-Perot structure interacting with hydroxyethyl cellulose

Polyimide-coated Fiber Bragg Grating for Relative Humidity Sensing

Bragg Grating Chemical Sensor with Hydrogel As Sensitive Element

High Sensitivity Relative Humidity Sensor Based on SMTF Structure Coated with Gelatin

Highly Sensitive Fiber Relative Humidity Sensor Based on Tip Michelson Interferometer With Agarose Gel Coating