Abstract:Olivine-type LiFePO4, as an important cathode material of lithium-ion batteries, has been paying numerous attentions owing to the high theoretical capacity, good cycle stability, environmental friendliness, safety, etc. But, for bulk LiFePO4 materials, there are some shortcomings such as the low conductivity of ca. 10(-9) S.cm(-1) and low diffusion coefficient of lithium ions. Some methods have been developed to improve its performance, including supporting, packaging, doping, and/or nanocrystallization. Carbon materials have been widely used in lithium-ion batteries as the conductive agent and modifier owing to the good conductivity, excellent electrochemical/mechanical stability, special pore structures favoring the mass transfer, low cost, and environmental friendliness. Among these, the conductivity and pore structure have a significant impact on the electrochemical performance of the cathode materials such as LiFePO4. The carbon nanomaterials with three-dimensional hierarchical structure are paying more and more attentions because of the special pore structure. Herein, we reported the high performance of the cathode materials, LiFePO4 supported on carbon nanocages (CNCs). CNCs are prepared using benzene as precursors and magnesium oxide as template, which have high specific surface area up to 1274 m(2).g(-1), excellent electrical conductivity of 1.44 S.cm(-1), multiscale pore structure, etc. The LiFePO4/CNCs nanocomposite was prepared following the procedure. CNCs were impregnated with the Li+, Fe2+ and PO43- -containing acid solutions, the final products were obtained by sintering at 700 degrees C under the gaseous mixture of Ar and 5 vol.% H-2. The component, structure, and electrochemical performances were investigated by X-ray diffraction, transmission electron microscope, thermogravimetry, and electrochemical tests. The LiFePO4 nanoparticles with the size of 10 similar to 25 um were homogeneously dispersed on CNCs. The bulk conductivity of LiFePO4/CNCs was 0.529 S.cm(-1), far higher than 2.27 X 10(-9) S.cm(-1) of pure LiFePO4. The LiFePO4/CNCs composite delivered a large discharge capacity of 163 mAh.g(-1) at a rate of 0.1 C, close to the theoretical capacity of LiFePO4. Even at the high rates of 15 C and 30 C, the discharge capacities still reach 96 and 75 mAh.g(-1), respectively. After 200 cycles at the high rate of 15 C, the tested cell still remains a specific capacity of 92 mAh.g(-1). These results indicated that the LiFePO4/CNCs composite as cathode material of lithium-ion batteries possessed excellent high-rate performance and cycling stability, superior to the LiFePO4/CNTs composite. It could be ascribed to high surface area, hierarchical porous structure, and excellent electrical conductivity of CNCs support as well as the nanoscale size and high crystallinity of LiFePO4 particles.

Synthesis, Characterization and Application of Carbon Nanocages As Anode Materials for High-Performance Lithium-Ion Batteries

Hierarchical Carbon Nanocages As High-Rate Anodes for Li- and Na-ion Batteries

Carbon Nanocages@ultrathin Carbon Nanosheets: One-step Facile Synthesis and Application As Anode Material for Lithium-Ion Batteries

Tailoring the Li+ Intercalation Energy of Carbon Nanocage Anodes Via Atomic Al‐Doping for High‐Performance Lithium‐Ion Batteries

Carbon Nanocages Supported LiFePO4 Nanoparticles as High-Performance Cathode for Lithium Ion Batteries

ZnFe2O4-nanocrystal-assembled Microcages As an Anode Material for High Performance Lithium-Ion Batteries

Carbon Nanocages with Nanographene Shell for High-Rate Lithium Ion Batteries

Fabrication of multi-layer CoSnO3@carbon-caged NiCo2O4 nanobox for enhanced lithium storage performance

Low Temperature Carbonization of Cellulose Nanocrystals for High Performance Carbon Anode of Sodium-Ion Batteries

Nitrogen-Doped Carbon Nanocages As High-Rate Anode for Lithium Ion Batteries

In Situ Nitrogen-Doped Helical Mesoporous Carbonaceous Nanotubes for Superior-High Lithium Anodic Performance

K-Functionalized Carbon Quantum Dots-Induced Interface Assembly of Carbon Nanocages for Ultrastable Potassium Storage Performance

Hollow carbon cage with nanocapsules of graphitic shell/nickel core as an anode material for high rate lithium ion batteries

Zn2geo4@C Core-Shell Nanorods As Highly Reversible Anode Materials for Lithium-Ion Batteries

Atomic layer deposition assisted fabrication of high-purity carbon nanocoil for electrochemical energy storage

Collapsed N&S Dual-Doped Carbon Nanocages As High-Density Anode for Ultrahigh Volumetric Performance of Li-ion Batteries

Graphitic Carbon Nanocage as a Stable and High Power Anode for Potassium‐Ion Batteries

Self-tunable Ultrathin Carbon Nanocups As the Electrode Material of Sodium-Ion Batteries with Unprecedented Capacity and Stability

Nitrogen and Oxygen Codoped Carbon Anode Fabricated Facilely from Polyaniline Coated Cellulose Nanocrystals for High-Performance Li-Ion Batteries

Co 3 O 4 Nanocages for High-Performance Anode Material in Lithium-Ion Batteries

Carbon Nanotube Array Anodes for High-Rate Li-ion Batteries