Abstract:In particular types of layer- or lamellar-like microstructures such as pearlite and lath martensite, plastic slip occurs favorably in directions parallel to inter-lamellar boundaries. This may be due to the interplay between morphology and crystallographic orientation or, more generally, due to constraints imposed on the plastic slip due to the lamellar microstructural geometry. This paper proposes a micromechanics based, computationally efficient, scale independent model for a particular type of lamellar microstructures containing softer lamellae which are sufficiently thin to be considered as discrete slip planes embedded in a matrix representing the harder lamellae. Accordingly, the model is constructed as an isotropic visco-plastic model which is enriched with an additional orientation-dependent planar plastic deformation mechanism. This additional mode is activated when the applied load, projected on the direction of the soft films, induces a significant amount of shear stress. Otherwise, the plastic deformation is governed solely by the isotropic part of the model. The response of the proposed model is assessed via a comparison to an infinite periodic two-phase laminate. It is shown that the yielding of the model follows the same behavior as the reference model. The proposed model is highly anisotropic, and the degree of anisotropy depends on the contrast between the slip resistance of the planar mode versus that of the isotropic part. The framework is then applied to the substructure of lath martensite with thin films of inter-lath retained austenite, and exploited in a mesoscale simulation of a dual-phase steel microstructure. The results are compared with those of a standard isotropic model and a full crystal plasticity model which does not have the additional planar plastic mechanism. Predictions made with the proposed model show distinct differences compared with the crystal plasticity results, while keeping the computational cost comparable to that of the isotropic model – and significantly lower than that of the crystal plasticity simulation.

Advanced Modeling of Plasticity of Linepipe Steels with Anisotropic Texture and Complex Loading History

Short-Term Mechanical Analysis of Polyethylene Pipe Reinforced by Winding Steel Wires Using Steel Wire Spiral Structural Finite Element Model

A Multi-Phase Model for Transformation Plasticity Using Thermodynamics-Based Metallurgical Algorithm

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Modeling of Low Cycle Behavior of P92 Steel Based on Cyclic Plasticity Constitutive Equations

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Influence of thickness and strength on plastic instability in tailored steel structures

Comparative Study and Application of a Coupled Nonlinear Kinematic Hardening Model for Structural Metallic Material Behavior

Non-associated anisotropic plasticity of metal sheets based on the distortional concept

An effective anisotropic visco-plastic model dedicated to high contrast ductile laminated microstructures: Application to lath martensite substructure

Experimental Investigation and Numerical Modelling of the Cyclic Plasticity and Fatigue Behavior of Additively Manufactured 316L Stainless Steel

Cyclic Plasticity Modeling of Nickel-Based Superalloy Inconel 718 under Multi-Axial Thermo-Mechanical Fatigue Loading Conditions

Stabilized cyclic stress‐strain calculation for metals under multiaxial loading

Modeling of Texture Development during Metal Forming Using Finite Element Visco-Plastic Self-Consistent Model

Cyclic plastic behavior analysis based on the micromorphic mixed hardening plasticity model

A Transition State Theory-Based Continuum Plasticity Model Accounting for the Local Stress Fluctuation

Cyclic plasticity behavior and deformation mechanism of 1Cr18Ni10Ti pressure pipe subjected to in-service loadings

Predicting Plastic Behavior of Magnesium Alloy Tube Bending with Comprehensive Constitutive Models

Multiple-mechanism and microstructure-based crystal plasticity modeling for cyclic shear deformation of TRIP steel

An Anisotropic Damage-Plasticity Constitutive Model of Continuous Fiber-Reinforced Polymers

Experimental studies and the model of anisotropic plasticity for additively manufactured stainless steel with stress state dependent properties