Abstract:Digital Elevation Model (DEM) derived from TerraSAR-X/TanDEM-X, can overcome the influence of atmospheric delay and surface deformation, and has a much higher resolution and precision compared with traditional InSAR. However, the DEM generated from TSX/TDX is vulnerable to geometric distortion such as layover, shadow, foreshortening etc. Moreover, the precision of TSX/TDX DEM, especially for different surface characteristic, such as mountainous areas, urban buildings and flat areas is still far from clear in application. Therefore, it has a practical significance on the guidance for DEM production derived from TSX/TDX. In this paper, we proposed a procedure which combines both ascending and descending measurements to obtain a high precision and resolution DEM product from the bistatic mode of TSX/TDX. We also use an iterative fusion method considering the perpendicular baseline and the location of layover and shadow as weighing. Because the ascending and descending SAR images have different geometrical conditions, such as incident angle and perpendicular baseline, it can regain the DEM affected by geometric distortion. We also adopted a quality assessment of the fusion DEM (5 meters resolution) for two terrain configurations to demonstrate the precision pattern. The fusion DEM in different kinds of terrain configurations; moderate topography and urban areas with dense high-rising buildings, is compared with DEM collected by Lidar technique in the study area. In addition, we qualitatively and quantitatively analyzed the improvement of fusion DEM in the processing of DInSAR technology compared with the existing external DEM. Two pairs of TSX/TDX data, acquired on 21 November 2011 in the ascending mode and 24 October 2013 in the descending mode, respectively, are used to map a fusion DEM in Zhuhai city and Macau. The results indicate that the fusion DEM with the proposed method can recover more information in the distorted areas compared with the DEM derived from a single platform. In order to validate the precision of the fusion DEM, a Lidar DEM with high resolution and precision of the research area are collected and compared. We find that the standard deviation (RMS) in mountainous areas is 3. 57 m with a decrease. of 8% and 22% for ascending and descending data, respectively. The standard deviation value in urban areas is 11. 85 m which also has a drop of 28% and 22% compared with two single platform. Moreover, the precision of the fusion DEM is high in residential areas with sparse buildings with a standard deviation 5 m. In addition, the TerraSAR-X pairs whose temporal baseline is 11days and perpendicular baseline is 135 m are used to conduct comparison of different kinds of external DEM in DInSAR processing. Moreover, statistical analysis of differential phase (pixel whose coherence is higher than 0. 8) in mountainous and urban areas are performed separately for a quantitative analysis. The results show that the fusion DEM used as an external DEM can remove topography phase better compared with SRTM and ASTER data especially in the mountainous area. The standard deviations of differential phases is 1. 4 rad, 1. 6 rad and 1. 4 rad for SRTM, ASTER and TanDEM, respectively. In urban areas with dense high buildings, the standard deviations are 1. 7 rad 1. 3 rad and 1. 1 rad respectively, which means higher resolution and precision of external DEM can improve the quality of DInSAR with high resolution SAR images. This work adopted an iterative fusion method to obtain high resolution and precision DEM. Locations of geometric distortion and perpendicular baseline are regarded as weighting factors to improve the efficiency of fusion procedure by comparing with traditional DEM. Besides, we also qualitatively and quantitatively analyzed the improvement of TSX/TDX DEM in traditional DInSAR, which can help us interpret deformation information and obtain a higher precision of time- series of InSAR.

Combined DEM Extration Method from StereoSAR and InSAR

A Comparative Study of DEM Reconstruction Using the Single-Baseline and Multibaseline InSAR Techniques

DEM Generation Using Bistatic Interferometry:High-Coherence Pixel Selection and Residual Reference Phase Compensation

Experimental Results and Algorithm Analysis of DEM Generation Using Bistatic SAR Interferometry with Stationary Receiver

SAR STEREO-MAPPING BASED ON DEM

Extraction of topographic map elements with SAR stereoscopic measurement

The Facilitation of SRTM DEM-derived Interferogram to Accurate DEM Reconstruction

Generating Dem of Very Narrow Baseline Stereo Using Multispectral Images

Sar clinometry-and interferometry-derived dem reconstruction

Estimation of Residual Motion Errors and Phase Ambiguity for Repeat-Pass In-CSAR Without External DEMs

Reconstruction Of Insar Dem Facilitated By Orbit Data And Srtm Data

High-precision, Fast DEM Reconstruction Method for Spaceborne InSAR

Stereo-measurement Model of SAR Image Pair Based on Image Simulation

Digital elevation model generation using multibaseline advanced land observing satellite/phased array type L-band synthetic aperture radar imagery

RECONSTRUCTING HIGH-ACCURACY DEM WITH PRECISE ORBIT DATA AND EXTERNAL DEM

Fixed-receiver Bistatic Interferometric Algorithms Analysis and Implementation

A Novel DEM Reconstruction Strategy Based on Multi-Frequency InSAR in Highly Sloped Terrain.

Elevation reconstruction combining sar intensity and interferometric phase data

Generation of high precision DEM from TerraSAR-X/TanDEM-X

DEM Reconstruction of Spaceborne Parasitic InSAR System

Interferometric DEM-Assisted High Precision Imaging Method for ArcSAR