Abstract:During deposition, modification, and etching of thin films and nanomaterials in reactive plasmas, many active species can interact with the sample simultaneously. This includes reactive neutrals formed by fragmentation of the feed gas, positive ions, and electrons generated by electron-impact ionization of the feed gas and fragments, excited states (in particular, long-lived metastable species), and photons produced by spontaneous de-excitation of excited atoms and molecules. Notably, some of these species can be transiently present during the different phases of plasma processing, such as etching of thin layer deposition. To monitor plasma-surface interactions during materials processing, a new system combining beams of neutral atoms, positive ions, UV photons, and a magnetron plasma source has been developed. This system is equipped with a unique ensemble of in-plasma surface characterization tools, including (1) a Rutherford Backscattering Spectrometer (RBS), (2) an Elastic Recoil Detector (ERD), and (3) a Raman spectroscopy system. RBS and ERD analyses are carried out using a differentially pumped 1.7 MV ion beam line Tandetron accelerator generating a beam at grazing incidence. The ERD system is equipped with an absorber and is specifically used to detect H initially bonded to the surface; higher resolution of surface H is also available through nuclear reaction analysis. In parallel, an optical port facing the substrate is used to perform Raman spectroscopy analysis of the samples during plasma processing. This system enables fast monitoring of a few Raman peaks over nine points scattered on a 1.6 × 1.6 mm2 surface without interference from the inherent light emitted by the plasma. Coupled to the various plasma and beam sources, the unique set of in-plasma surface characterization tools detailed in this study can provide unique time-resolved information on the modification induced by plasma. By using the ion beam analysis capability, the atomic concentrations of various elements in the near-surface (e.g., stoichiometry and impurity content) can be monitored in real-time during plasma deposition or etching. On the other hand, the evolution of Raman peaks as a function of plasma processing time can contribute to a better understanding of the role of low-energy ions in defect generation in irradiation-sensitive materials, such as monolayer graphene.

Monitor of the Chamber Wall Condition in Plasma Etching Process by APM Sensor

In situ monitoring of FDM machine condition via acoustic emission

Use of plasma process diagnostic sensors for the monitoring of in situ dry cleaning of plasma enhanced chemical vapor deposition chamber

Real-time monitoring of the plasma density distribution in low-pressure plasmas using a flat-cutoff array sensor

Development of Wafer-Type Plasma Monitoring Sensor with Automated Robot Arm Transfer Capability for Two-Dimensional In Situ Processing Plasma Diagnosis

Preliminary empirical results suggesting the mapping of dynamic in situ process signals to real-time wafer attributes in a plasma etch process

Virtual Sensor Based Fault Detection and Classification on a Plasma Etch Reactor

The Acoustic Micro Integrated Detection Technique for Silicon Wafer Processing

Multilayered Surface Plasma Resonance Waveguide Sensing Device

Flat cutoff probe for real-time electron density measurement in industrial plasma processing

Acoustic plate mode tissue sensor

Design and Fabrication of a Sensors-integrated Silicon Electrode for Gap Status Monitoring in Micro Electrochemical Machining

A novel application of acoustic plate mode sensor in tissue regeneration

Cu Layer Thickness Monitoring in CMP Process by Using Eddy Current Sensor

Real-Time Plasma Uniformity Monitoring via Selective Plasma Light Intensity Measurement Using Transparent-LCD-Module-Adapted Optical Emission Spectroscopy

In-plasma analysis of plasma-surface interactions

Development of Virtual Metrology Using Plasma Information Variables to Predict Si Etch Profile Processed by SF6/O2/Ar Capacitively Coupled Plasma

Study of Plug Etch back process matching on faraday shielded ICP and traditional CCP plasma ETCH chambers

Increase of process reliability in the micro-machining processes EDM-milling and laser ablation using on-machine sensors

Health Monitoring of Single-Element Piezoelectric Transducer Using Its Electromechanical Admittance

Plasma Panel Sensors for Particle and Beam Detection