Abstract:Inorganic perovskite materials have gained considerable attention owing to their good thermal stability, high absorption coefficient, adjustable bandgap, and simple preparation. However, most inorganic perovskites are sensitive to water and need to be prepared under inert environments in a glove box, which increases their preparation cost. In this study, we used a simple one-step spin coating anti-solvent process to prepare CsPbI2Br, which was then annealed in humid air (relative humidity < 35%) at 300 degrees C for 5 min with isopropanol as the anti-solvent. An inorganic perovskite solar cell with fluorine-doped tin dioxide/compact TiO2/mesoporous TiO2/CsPbI2Br/hole transport materials/Ag structure was prepared. By varying the concentration of the mesoporous precursor, we controlled the thickness of mesoporous TiO2 in order to investigate its effect on the properties of the perovskite films and devices. The X-ray diffraction (XRD) results confirmed the successful synthesis of CsPbI2Br in humid air. Moreover, the thickness of the substrate affected the crystal growth orientation. The scanning electron microscopy results revealed that the thickness of the mesoporous titanium dioxide substrate affected the crystallization processing of CsPbI2Br, resulting in the formation of compounds with different morphologies and phases. The ultraviolet-visible (UV-Vis) and photoluminescence spectra of the perovskite materials revealed that the substrate thickness affected their optical properties. With a decrease in the thickness of the mesoporous TiO2 substrate, the bandgap of CsPbI2Br increased slightly. At the substrate thickness of 145 nm, the defect density of state of CsPbI2Br increased. At the optimum mesoporous titanium dioxide substrate thickness of 732 nm, the device showed the best power conversion efficiency of 8.16%. The electrochemical impedance spectroscopy measurements revealed that the devices prepared on thicker mesoporous layers showed better carrier extraction and transmission capabilities but higher interfacial charge recombination resistance, leading to a lower open-circuit voltage but higher current density. Thus, an increase in the thickness of the mesoporous substrate improved the photovoltaic performance of the devices. The stability of the CsPbI2Br perovskite film improved with an increase in the mesoporous substrate thickness. The stability test results along with the UV-Vis and XRD analysis results showed that the perovskite film prepared on the 732 nm-thick substrate showed no significant structure change after being placed in humid air for 144 h. The stability of the perovskite solar cells was also investigated. The device with the 732 nm-thick substrate could maintain its original efficiency of 73% after exposure to air with relative humidity less than 35% for 72 h. Thus, inorganic perovskite solar cells could be successfully prepared in the humid air environment.

Exceptionally Stable CH3NH3PbI3 Films in Moderate Humid Environmental Condition

Photostability and Moisture Stability of Ch3nh3pbi3-Based Solar Cells by Ethyl Cellulose

Degradation mechanism of CH3NH3PbI3 perovskite materials upon exposure to humid air

First-Principles Calculations of Graphene-Coated CH3NH3PbI3 Toward Stable Perovskite Solar Cells in Humid Environments

Investigation of CH3NH3PbI3 degradation rates and mechanisms in controlled humidity environments using in situ techniques.

Enhanced stability in cesium assisted hybrid 2D/3D-perovskite thin films and solar cells prepared in ambient humidity

Fabrication of Stable CsPbI2Br Perovskite Solar Cells in the Humid Air

Moisture Stability of Perovskite Solar Cells Processed in Supercritical Carbon Dioxide

Ambient Air Temperature Assisted Crystallization for Inorganic CsPbI2Br Perovskite Solar Cells

Air-Induced High-Quality Ch3nh3pbi3 Thin Film for Efficient Planar Heterojunction Perovskite Solar Cells

Enhanced Optoelectronic Quality of Perovskite Films with Excess CH3NH3I for High-Efficiency Solar Cells in Ambient Air

Efficient and Stable CH3NH3PbI3-x(SCN)x Planar Perovskite Solar Cells Fabricated in Ambient Air with Low-Temperature Process

Hydrophobic Hole-Transporting Layer Induced Porous Pbi2 Film for Stable and Efficient Perovskite Solar Cells in 50% Humidity

Enhanced Photovoltaic Performance and Thermal Stability of CH3NH3PbI3 Perovskite Through Lattice Symmetrization.

Realization of Moisture-Resistive Perovskite Films for Highly Efficient Solar Cells Using Molecule Incorporation

Enhanced stability in CH3NH3PbI3 hybrid perovskite from mechano-chemical synthesis: structural, microstructural and optoelectronic characterization

(C6H5NH3)BiI4: A Lead-Free Perovskite with >330 Days Humidity Stability for Optoelectronic Applications

Facile Face-Down Annealing Triggered Remarkable Texture Development in CH3NH3PbI3 Films for High-Performance Perovskite Solar Cells.

Evolution of Photoluminescence, Raman, and Structure of CH3NH3PbI3 Perovskite Microwires under Humidity Exposure

Intrinsic Instability of the Hybrid Halide Perovskite Semiconductor CH3NH3PbI3

Vacuum-Assisted Thermal Annealing of CH3NH3PbI3 for Highly Stable and Efficient Perovskite Solar Cells