Abstract:Poly(lactic-co-glycolic acid) (PLGA) is a widely used polymeric biomaterial due to its excellent biocompatibility and biodegradation. Asymmetric PLGA hollow fiber membranes (HFMs) have been extensively used as porous tubular scaffolds for tissue engineering, e.g. for nerve conduits and artificial blood vessels. PLGA HFMs are generally fabricated through a dry-jet wet spinning process, and the porous morphology of PLGA HFMs induced by polymer/solvent/nonsolvent ternary phase inversion plays a key role in their biomedical performance. In this study, PLGA was dissolved in dimethyl sulfoxide (DMSO) as the dope fluid, and deionized water with different DMSO contents was used as the bore fluid. The influence of bore fluid composition on the HFM morphology and performance was investigated by measuring phase separation time, porosity, mechanical properties, and in vitro hydrolytic degradation. The results indicated that with increased bore fluid DMSO content, the inner and outer diameters, as well as the wall thickness of the HFMs, decreased significantly; also, the inner surface became more porous and the inner surface pore size and porosity increased. Cross-sectional SEM images showed that the middle layer of the five-layered microstructure gradually changed from large voids to finger-like microvoids when the DMSO content in bore fluid increased from 0% to 60%. Furthermore, the HFMs resulting from higher DMSO content in bore fluid had a lower porosity, a faster degradation rate, a higher Young's modulus, and a lower suture retention strength. More importantly, the in vitro cell culture on the inner surface of PLGA HFMs showed that PC12 cells cultured on HFMs prepared with 60% DMSO bore fluid exhibited better cell adhesion, longer neurite length, and alignment along the HFM longitudinal axis. A ternary phase diagram and the Flory-Huggins theory were applied to analyze HFM morphological formation. The study contributes to understanding of the mechanism of HFM porous morphology formation and should guide potential application of PLGA HFMs as tissue engineering scaffolds.

Numerical Study and Scale Analysis of Inner and Outer Diameters Prediction in Fabrication of Hollow Fiber Membranes for Nerve Regeneration

Groove Formation Modeling in Fabricating Hollow Fiber Membrane for Nerve Regeneration

Fabrication of Inner Grooved Hollow Fiber Membranes Using Microstructured Spinneret for Nerve Regeneration

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Investigation of Inner Surface Groove Formation under Radially Inward Pressure During Immersion Precipitation-Based Hollow Fiber Membrane Fabrication

Porous Morphology and Mechanical Properties of Poly(lactide-Co-glycolide) Hollow Fiber Membranes Governed by Ternary-Phase Inversion

Effect of Bore Fluid Composition on Poly(lactic-Co-glycolic Acid) Hollow Fiber Membranes Fabricated by Dry-Jet Wet Spinning

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

A Machine Learning Approach to Model the Electrospinning Process of Biocompatible Materials

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Three-dimensional CFD modeling for hollow fiber gas separation membrane modules based on a dual porous media model

Micro/nanofabrication of Brittle Hydrogels Using 3D Printed Soft Ultrafine Fiber Molds for Damage-Free Demolding.

Fabrication of Heterogeneous Scaffolds Using Melt Electrospinning Writing: Design and Optimization

Numerical Model of Jet Formation During Melt Electrowriting for Fabrication of Precise Structures

Investigation of Transport Property of Fibrous Media: 3D Virtual Modeling and Permeability Calculation

Modelling of hollow fiber membrane bioreactor for mammalian cell cultivation using computational hydrodynamics

Response Surface Methodology to Explore the Influence Mechanism of Fiber Diameter in a New Multi-Needle Electrospinning Spinneret

Artificial neural networks for the accurate prediction of the thickness of fiber membranes prepared by airflow‐assisted electrostatic spinning

Electrospun nanofiber membrane diameter prediction using a combined response surface methodology and machine learning approach

Modeling the density gradient of 3D nanofiber scaffolds fabricated by divergence electrospinning

3D CFD Analysis of Geometrical Design Impact on Hydrodynamic Performance in Hollow Fiber Membrane Contactors