Sintering of Nanograin Ceramics

I. -Wei Chen,Xiaohui Wang

DOI: https://doi.org/10.1002/9783527631940.ch48

2011-01-01

Abstract:This chapter contains sections titled: Introduction Background: What Went Wrong With Conventional Thinking? Two-Step Sintering of Y2O3 Two-Step Sintering of Other Ceramics Conclusions References

What problem does this paper attempt to address?

Sintering of Nano-Ceramics

Xiao-Hui Wang,I-Wei Chen

DOI: https://doi.org/10.1201/9781315371795-20

2006-01-01

Abstract:This chapter provides an outline of major techniques that are available for fabricating dense nanocrystalline ceramics, starting with powders. It emphasizes the importance of agglomeration-free green-body fabrication and two-step sintering (TSS), the latter being a unique, unconventional, yet industrially viable process capable of densification without grain growth. The chapter describes the kinetic of constant structure sintering in yttria and the successful application of TSS approach to several oxide and nonoxide ceramics with outstanding properties. TSS exploits the difference in the kinetics between grain boundary diffusion and grain boundary migration at low temperature, and it has been demonstrated for simple oxides, complex oxides, and liquid-phase sintered zinc oxide and silicon carbide. The simplicity of TSS approach should also make it a useful tool for preparing model systems to study grain-size-dependent properties in nanostructured materials and grain boundary kinetics at low temperatures.
Two-Step Sintering of Ceramics with Constant Grain-Size, I. Y2O3

Xiao-Hui Wang,Pei-Lin Chen,I-Wei Chen

DOI: https://doi.org/10.1111/j.1551-2916.2005.00763.x

IF: 4.186

2006-01-01

Journal of the American Ceramic Society

Abstract:Isothermal and constant-grain-size sintering have been carried out to full density in Y2O3 with and without dopants, at as low as 40% of the homologous temperature. The normalized densification rate follows Herring's scaling law with a universal geometric factor that depends only on density. The frozen grain structure, however, prevents pore relocation commonly assumed in the conventional sintering models, which fail to describe our data. Suppression of grain growth but not densification is consistent with a grain boundary network pinned by triple-point junctions, which have a higher activation energy for migration than grain boundaries. Long transients in sintering and grain growth have provided further evidence of relaxation and threshold processes at the grain boundary/triple point.
Two‐Step Sintering of Ceramics with Constant Grain‐Size, II: BaTiO3 and Ni–Cu–Zn Ferrite

XH Wang,XY Deng,HL Bai,H Zhou,WG Qu,LT Li,IW Chen

DOI: https://doi.org/10.1111/j.1551-2916.2005.00728.x

IF: 4.186

2006-01-01

Journal of the American Ceramic Society

Abstract:We investigated the preparation of bulk dense nanocrystalline BaTiO3 and Ni–Cu–Zn ferrite ceramics using an unconventional two‐step sintering strategy, which offers the advantage of not having grain growth while increasing density from about 75% to above 96%. Using nanosized powders, dense ferrite ceramics with a grain size of 200 nm and BaTiO3 with a grain size of 35 nm were obtained by two‐step sintering. Like the previous studies on Y2O3, the different kinetics between densification diffusion and grain boundary network mobility leaves a kinetic window that can be utilized in the second‐step sintering. Evidence indicates that low symmetry, ferroelectric structures still exist in nanograin BaTiO3 ceramics, and that saturation magnetization is the same in nanograin and coarse grain ferrite ceramics.
Making Nanostructured Ceramics from Micrometer-Sized Powders via Grain Refinement During SPS Sintering

Kepi Chen,Xiaowen Zhang,Hui Wang,Ligong Zhang,Jing Zhu,Fuqian Yang,Linan An

DOI: https://doi.org/10.1111/j.1551-2916.2008.02490.x

IF: 4.186

2008-01-01

Journal of the American Ceramic Society

Abstract:In this paper, we have demonstrated that dense bulk nanostructured ceramics can be synthesized from micrometer-sized powders by using an electrical field-activated sintering process. A dense Pb(Mg1/3Nb2/3)O-3-PbTiO3 ceramic with grain sizes of 20-100 nm was obtained from the starting powder of 1 to 10 mu m. Structural and property analysis confirmed that the entire specimen is composed of nano-sized grains. The significant microstructural refining is attributed to a pulsed electric field-induced thermo-mechanical fatigue process, which in situ "shattered" the large particles into nano-sized grains during sintering. An advantage of this technique over the previous ones is that it avoids the usage of ultrafine nanometer-sized powders, which are difficult to process and mass produce in an economic and consistent way. In principle, the process demonstrated here can be applied to other material systems.
Mobility Transition at Grain Boundaries in Two-Step Sintered 8 mol% Yttria Stabilized Zirconia

Yanhao Dong,I-Wei Chen

DOI: https://doi.org/10.1111/jace.15362

2017-08-15

Abstract:Stagnation of grain growth is often attributed to impurity segregation. Yttria-stabilized cubic zirconia does not evidence any segregation-induced slowdown, as its grain growth obeys the parabolic law when the grain size increases by more than one order of magnitude. However, lowering the temperature below 1300 oC triggers an abrupt slowdown, constraining the average grains to grow by less than 0.5 ${\mu}$m in 1000 h despite a relatively large driving force imparted in the fine grains of ~0.5 ${\mu}$m. Yet isolated pockets of abnormally large grains, along with pockets of abnormally small grains, emerge in the same latter sample. Such microstructure bifurcation has never been observed before, and can only be explained by an inhomogeneous distribution of immobile four-grain junctions. The implications of these findings for two-step sintering are discussed.

Materials Science
Mobility Transition at Grain Boundaries in Two-Step Sintered 8mol% Yttria-Stabilized Zirconia

Yanhao Dong,I-Wei Chen

DOI: https://doi.org/10.1111/jace.15362

IF: 4.186

2017-01-01

Journal of the American Ceramic Society

Abstract:Stagnation of grain growth is often attributed to impurity segregation, which becomes more severe as the grain size grows. In this respect, there is no evidence for segregation-induced slowdown in the grain growth of yttria-stabilized cubic zirconia, which obeys the parabolic law when the size increases by more than ten times. However, lowering the temperature below 1300 degrees C triggers an abrupt slowdown, constraining the average grains to grow by less than 0.5m in 1000hours despite a relatively large driving force imparted in the fine grains of similar to 0.5m. Yet isolated pockets of abnormally large grains, and even most remarkably, pockets of abnormally small grains, emerge in the same latter sample. Such extreme bifurcation of microstructure has never been observed before, and can be explained by an inhomogeneous distribution of immobile four-grain junctions. The implications of these findings for two-step sintering are discussed.
Sintering Kinetics and Microstructure Evolution in Α-Al2o3 Nanocrystalline Ceramics: Insensitive to Fe Impurity

Hongbing Yang,Lu Li,Wenbin Cao,Yuhang Liu,Masood Mukhtar,Libin Zhao,Yueming Kang,Yanhao Dong,Jiangong Li

DOI: https://doi.org/10.1016/j.jeurceramsoc.2019.11.079

IF: 5.7

2020-01-01

Journal of the European Ceramic Society

Abstract:Diffusion kinetics, processing, and microstructures of alumina ceramics have been of great scientific and technological interests. Here we reported the sintering kinetics and microstructure evolution in high-purity dispersed ultrafine alpha-Al2O3 nanoparticles with superior sinterability. An extremely fine grain size of 34 nm with 99.6 % theoretical density and a uniform microstructure can be produced by two-step pressureless sintering. Systematic kinetic analysis further points out to a surprising insensitivity of alpha-Al2O3 nanocrystalline ceramics to Fe and other impurities, which contrasts with prior reports in the literature. We propose this insensitivity is originated from extensive grain boundaries in nanocrystalline ceramics, which allows segregation of impurities and lowers their concentrations at grain boundaries.
Grain growth competition during sintering of SrTiO3 nanocrystals: Ordered coalescence of nanocrystals versus conventional mechanism

Jianfeng Hu,Zhijian Shen

DOI: https://doi.org/10.1016/j.scriptamat.2020.113703

IF: 6.302

2021-03-01

Scripta Materialia

Abstract:Grain growth plays a crucial role in developing the microstructures of polycrystalline materials during heating treatment. In this work, SrTiO3 ceramics sintered at different heating rates (10°C/min and 100°C/min) display the distinctly different grain growth behaviors and microstructures between them. The onset temperature of rapid grain growth and mechanical-performance-related fracture mode are apparently different between these two sets of samples. Two grain growth mechanisms are demonstrated to dominate separately the sintering of SrTiO3 nanocrystals at different heating rates, i.e. conventional mechanism of atom-by-atom additions for grain growth at 10°C/min and ordered coalescence of nanocrystals for grain growth at 100°C/min. It is demonstrated that the switch of growth mechanisms is determined by the competition between the activation of grain motions and the formation of steady neck among grains.

materials science, multidisciplinary,nanoscience & nanotechnology,metallurgy & metallurgical engineering
Current understanding and future research directions at the onset of the next century of sintering science and technology

Rajendra K. Bordia,Suk‐Joong L. Kang,Eugene A. Olevsky

DOI: https://doi.org/10.1111/jace.14919

IF: 4.186

2017-05-16

Journal of the American Ceramic Society

Abstract:Abstract Sintering and accompanying microstructural evolution is inarguably the most important step in the processing of ceramics and hard metals. In this process, an ensemble of particles is converted into a coherent object of controlled density and microstructure at an elevated temperature (but below the melting point) due to the thermodynamic tendency of the particle system to decrease its total surface and interfacial energy. Building on a long development history as a major technological process, sintering remains among the most viable methods of fabricating novel ceramics, including high surface area structures, nanopowder‐based systems, and tailored structural and functional materials. Developing new and perfecting existing sintering techniques is crucial to meet ever‐growing demand for a broad range of technologically significant systems including, for example, fuel and solar cell components, electronic packages and elements for computers and wireless devices, ceramic and metal‐based bioimplants, thermoelectric materials, materials for thermal management, and materials for extreme environments. In this study, the current state of the science and technology of sintering is presented. This study is, however, not a comprehensive review of this extremely broad field. Furthermore, it only focuses on the sintering of ceramics. The fundamentals of sintering, including the thermodynamics and kinetics for solid‐state‐ and liquid‐phase‐sintered systems are described. This study summarizes that the sintering of amorphous ceramics (glasses) is well understood and there is excellent agreement between theory and experiments. For crystalline materials, attention is drawn to the effect of the grain boundary and interface structure on sintering and microstructural evolution, areas that are expected to be significant for future studies. Considerable emphasis is placed on the topics of current research, including the sintering of composites, multilayered systems, microstructure‐based models, multiscale models, sintering under external stresses, and innovative and novel sintering approaches, such as field‐assisted sintering. This study includes the status of these subfields, the outstanding challenges and opportunities, and the outlook of progress in sintering research. Throughout the manuscript, we highlight the important lessons learned from sintering fundamentals and their implementation in practice.

materials science, ceramics
A novel two-step cold sintering process to fabricate dense ZnO nanocrystalline ceramics

Jiaochun Zheng,Mao Deng,Yang Shi,Zhangyi Huang,Haomin Wang

DOI: https://doi.org/10.1016/j.jeurceramsoc.2023.10.053

IF: 5.7

2023-12-18

Journal of the European Ceramic Society

Abstract:The cold sintering process, a novel technique for low-temperature ceramic processing, effectively removes interparticle pores via dissolution and re-precipitation. However, it often triggers grain growth, especially in nanocrystalline ceramics. To address this issue, the present study proposed an innovative two-step cold sintering process with an initial step at 1.5 GPa/RT (room temperature) for 10 min, followed by a subsequent step at 300 MPa/250 °C for 45 min. This method yields ZnO nanocrystalline ceramics with 97.5 % relative density and a 39 nm average grain size (from 30 nm powder). The initial high-pressure step significantly enhances the pressure gradient and particle solubility, leading to very high supersaturation and the occurrence of homogenous nucleation during pressure release. Subsequently, the formation of the crystal nuclei in the interparticle voids can dramatically improve the density of the compact by the additional pore filling and avoid recrystallization-induced grain growth during the second-step cold sintering process.

materials science, ceramics
Grain characters and sintering properties of YSZ nanocrystalline powders

MF Han,SP Peng,BT Li

2003-01-01

Rare Metal Materials and Engineering

Abstract:The sintering process of YSZ nanocrystalline powders with the size range of 10 nm similar to 100 nm was researched. As a result, the starting sintering temperature of powders is mainly related to the first size of particles. The finer the powder is, the lower the starting sintering temperature is. The start sintering temperatures of powders with sizes of-15 nm, 30 nm and 50 nm are 825degreesC, 924degreesC and 966degreesC separately. The sintering densification process of adobe is tightly related to distribution of powders as well as the first size of particles. Powders with high surface, small agglomerates size and narrow span of grain distribution expressed better sintering properties.
Sintering behaviour and mechanical properties of SiC/YAG composite powders by sol-gel methods

Xingzhong Guo,Hui Yang,Jianwu Wang

DOI: https://doi.org/10.3321/j.issn:1002-185x.2004.z1.017

2004-01-01

Rare Metal Materials and Engineering

Abstract:On the basis of the preparation of SiC/ (Al2O3+Y2O3) composite powder, the sintering behaviour, mechanical properties and YAG phase distribution of SiC/ (Al2O3+Y2O3) composite ceramics were studied. The results showed that the composite powder had a low sintering temperature, a rapid densification rate. The SiC/YAG ceramics LP-sintered at 1 950 degrees C for 45 min had 96.8% of relative density, 356 MPa of bending strength, 23 GPa of hardness, and 4.5 MPa(.)m(1/2) of fracture toughness. The crystal was complete, its grain size was 0.5 mu m similar to 2 mu m and the fracture style was along-crystal.
Sintering, Properties and Applications of Silicon Nitride and Sialon Ceramics

Mamoru MITOMO,Yo TAJIMA

DOI: https://doi.org/10.2109/jcersj.99.1014

1991-01-01

Journal of the Ceramic Society of Japan

Abstract:There have been a great deal of progress in the development of high performance silicon nitride and sialon ceramics, largely owing to better understandings of sintering phenomena and processing-microstructure-properties relations. In this paper, sintering mechanisms and factors affecting sintering are reviewed for the systems with both soluble and insoluble additives, followed by discussions on the microstructure-properties relations. By choosing appropriate chemical compositions and sintering conditions, it has become possible to fabricate tough “in-situ composites” having bimodal grain size distributions or heat resistant ceramics with little grain boundary glass. Some examples of applications as heat engine components and industrial parts are also shown.

materials science, ceramics
High-Density Micro- and Nano-Grain Size Ceramics. Transition from Open into Closed Pores. Part 3. Workpiece Sintering without External Pressure1

A. V. Belyakov

DOI: https://doi.org/10.1007/s11148-020-00428-w

2020-05-01

Refractories and Industrial Ceramics

Abstract:An explanation of processes occurring during preparation of high-density micro- and nanogranular ceramics without using external pressure on the basis of published data is proposed. It is well known that pore growth commences after the start of transition of open into closed pores that begins with about 30 % open porosity. It is necessary to maintain open pores to the maximum possible sintered ceramic overall density. The article describes different methods of ceramic sintering making it possible to prepare high-density pore-free ceramics.

materials science, ceramics
Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Haiyue Xu,Ji Zou,Weimin Wang,Hao Wang,Wei Ji,Zhengyi Fu

DOI: https://doi.org/10.1016/j.jeurceramsoc.2020.08.018

IF: 5.7

2021-01-01

Journal of the European Ceramic Society

Abstract:Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (Cf/C) composite for spark plasma sintering, two kinds of commercially pure α-Al2O3 powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (Tsg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al2O3 powder and 1400 °C for the 3 μm Al2O3 powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al2O3 compact can reach ∼80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.

materials science, ceramics
Influences of powder morphology on the densification and microstructure of a ZrO2‐based nanocrystalline glass‐ceramic

Le Fu,Lei Li,Yongxin Cheng,Bohan Wang,Hui Wu

DOI: https://doi.org/10.1111/jace.18767

IF: 4.186

2022-09-03

Journal of the American Ceramic Society

Abstract:Morphology is an important characteristic of raw powder utilized for ceramic sintering but the role of powder morphology is mostly overlooked. In this study, two types of ZrO2‐SiO2 powder with different morphologies (fiber and particle) were synthesized by blow spinning and sol‐gel method, respectively, followed by DC electric field‐assisted hot pressing (FAHP) to obtain nanocrystalline glass‐ceramics. Results showed that the two as‐synthesized powders had different pyrolysis behaviors. The two types of as‐synthesized powders were amorphous and tetragonal‐ZrO2 nanocrystallites firstly formed after calcination at 800°C. During FAHP, the particle powder can be densified at a lower temperature than that of the fiber powder, due to the facts that the particle powder showed higher specific surface area and higher densification driving force. The fiber powder was predominately densified by fiber fusion and plastic deformation, whereas, the particle powder was densified via particle fusion. Both the two types of powder can be fully densified to obtain ZrO2‐SiO2 nanocrystalline glass‐ceramics (NCGCs) at 1230°C for 4 mins. Tetragonal‐ZrO2 nanocrystallites in the NCGCs with particles as raw powder showed higher stability than those in the NCGCs with fibers as raw powder. This article is protected by copyright. All rights reserved

materials science, ceramics
Sintering-Induced Phase Transformation of Nanoparticles: A Molecular Dynamics Study

Qian Mao,Yihua Ren,Kai H. Luo,Shuiqing Li

DOI: https://doi.org/10.1021/acs.jpcc.5b08625

2015-01-01

Abstract:Sintering-induced phase transformation of TiO2 nanoparticles is investigated systematically via molecular dynamics simulation. Upon defining a coordination number and bond angle distribution criteria, local phase information is identified for each individual Ti atom originating from amorphous or crystal structure as well as three TiO2 polymorphs, anatase, brookite, and rutile. Size-dependent structures of nanoparticles lead to different dynamics of the sintering-induced phase transformation. Grain boundaries that form between nanoparticles during sintering trigger the nucleation and growth of new phases. During the sintering of two equal-sized core shell anatase nanoparticles, crystal core regions melt with the temperature increase and the surface energy decrease in the microcanonical (NVE) ensemble. The new phase that develops from the grain boundary spreads into the destroyed core regions in stages, forming a new larger spherical nanoparticle with an ordered atomic arrangement. During the sintering of two unequal-sized nanoparticles (amorphous and core shell anatase), atoms from the amorphous nanoparticle first nucleate to form crystal anatase in the contact region, and a grain boundary is then developed between the original core region and the newly formed anatase crystal. After that, phase transformation follows much the same route as the equal-sized case from anatase to brookite.
Ultra-uniform Nanocrystalline Materials via Two-Step Sintering

Yanhao Dong,Hongbing Yang,Lin Zhang,Xingyu Li,Dong Ding,Xiaohui Wang,Ju Li,Jiangong Li,I-Wei Chen

DOI: https://doi.org/10.1002/adfm.202007750

2020-09-10

Abstract:Nanocrystalline metals and ceramics with <100 nm grain sizes and superior properties (e.g., mechanical strength, hardness, fracture toughness and stored dielectric energy) are of great interest. Much has been discussed about achieving nano grains, but little is known about maintaining grain-size uniformity that is critical for material reliability. An especially intriguing question is whether it is possible to achieve a size distribution narrower than what Hillert[1] theoretically predicted for normal grain growth, a possibility suggested, for growth with a higher growth exponent, by the generalized mean-field theory[2] of Lifshitz, Slyozov, Wagner (LSW)[3,4] and Hillert but never realized in practice. We demonstrate that this can be achieved in bulk materials with an appropriately designed two-step sintering route that (a) takes advantage of the large growth exponent in the intermediate sintering stage to form a most uniform microstructure despite porosity remaining, and (b) freezes the grain growth thereon while continuing densification to reach full density. The resultant dense bulk Al2O3 ceramic has an average grain size of 34 nm and a much narrower size distribution than Hillert's prediction. Bulk Al2O3 with a grain-size distribution narrower than the particle-size distribution of starting powders was also demonstrated using this strategy, as were highly uniform bulk engineering metals and ceramics of either high purity and high melting points (Mo and W-Re) or highly complex compositions (core-shell BaTiO3 and 0.87BaTiO3-0.13Bi(Zn2/3(Nb0.85Ta0.15)1/3)O3).

Materials Science
Issues in nanocomposite ceramic engineering: focus on processing and properties of alumina-based composites

Paola Palmero,Frank Kern,Frank Sommer,Mariangela Lombardi,Rainer Gadow,Laura Montanaro

DOI: https://doi.org/10.5301/jabfm.5000185

2014-12-30

Abstract:Ceramic nanocomposites, containing at least one phase in the nanometric dimension, have received special interest in recent years. They have, in fact, demonstrated increased performance, reliability and lifetime with respect to monolithic ceramics. However, a successful approach to the production of tailored composite nanostructures requires the development of innovative concepts at each step of manufacturing, from the synthesis of composite nanopowders, to their processing and sintering.This review aims to deepen understanding of some of the critical issues associated with the manufacturing of nanocomposite ceramics, focusing on alumina-based composite systems. Two case studies are presented and briefly discussed. The former illustrates the benefits, in terms of sintered microstructure and related mechanical properties, resulting from the application of an engineering approach to a laboratory-scale protocol for the elaboration of nanocomposites in the system alumina-ZrO2-YAG (yttrium aluminium garnet). The latter illustrates the manufacturing of alumina-based composites for large-scale applications such as cutting tools, carried out by an injection molding process. The need for an engineering approach to be applied in all processing steps is demonstrated also in this second case study, where a tailored manufacturing process is required to obtain the desired results.
Effects of Adding Methods of YAG on Sintering Behaviour, Mechanical Properties and Microstructure of SiC Ceramic

GUO Xing-zhong,YANG Hui,WANG Jian-wu,GAO Li-Hua,LI Xiang-yun

DOI: https://doi.org/10.3321/j.issn:1004-0609.2005.04.005

2005-01-01

The Chinese Journal of Nonferrous Metals

Abstract:SiC composite powders were respectively synthesized by sol-gel method and mechanical mixing method, and were pressureless liquid-phase sintered to prepare silicon carbide ceramic. The effects of adding methods on the sintering behaviour, mechanical properties and microstructure of silicon carbide ceramic were analyzed. The results show that at the sintering temperature of 1950℃, silicon carbide ceramic, with SiC/(Al_2O_3+Y_2O_3) composite powder by mechanical mixing method, possesses higher sintering properties, higher mechanical properties and more ideal microstructure than those with SiC/YAG composite powder by sol-gel method, and there exists over-sintering phenomenon in the SiC/YAG composite powder. After optimizing the process, silicon carbide ceramic, sintered at (1860℃) with SiC/YAG composite powder by sol-gel method, can obtain excellent sintering and mechanical properties and perfect microstructure. Formation ahead of sintering and uniform distribution of YAG phase in composite powder can accelerate the densification, decrease sintering temperature and improve mechanical properties and microstructure of silicon carbide ceramic. The fine grains, crack deflexion and grain-bridging are main toughening mechanisms of silicon carbide ceramic.

Sintering of Nanograin Ceramics

Sintering of Nano-Ceramics

Two-Step Sintering of Ceramics with Constant Grain-Size, I. Y2O3

Two‐Step Sintering of Ceramics with Constant Grain‐Size, II: BaTiO3 and Ni–Cu–Zn Ferrite

Making Nanostructured Ceramics from Micrometer-Sized Powders via Grain Refinement During SPS Sintering

Mobility Transition at Grain Boundaries in Two-Step Sintered 8 mol% Yttria Stabilized Zirconia

Mobility Transition at Grain Boundaries in Two-Step Sintered 8mol% Yttria-Stabilized Zirconia

Sintering Kinetics and Microstructure Evolution in Α-Al2o3 Nanocrystalline Ceramics: Insensitive to Fe Impurity

Grain growth competition during sintering of SrTiO3 nanocrystals: Ordered coalescence of nanocrystals versus conventional mechanism

Current understanding and future research directions at the onset of the next century of sintering science and technology

A novel two-step cold sintering process to fabricate dense ZnO nanocrystalline ceramics

Grain characters and sintering properties of YSZ nanocrystalline powders

Sintering behaviour and mechanical properties of SiC/YAG composite powders by sol-gel methods

Sintering, Properties and Applications of Silicon Nitride and Sialon Ceramics

High-Density Micro- and Nano-Grain Size Ceramics. Transition from Open into Closed Pores. Part 3. Workpiece Sintering without External Pressure1

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Influences of powder morphology on the densification and microstructure of a ZrO2‐based nanocrystalline glass‐ceramic

Sintering-Induced Phase Transformation of Nanoparticles: A Molecular Dynamics Study

Ultra-uniform Nanocrystalline Materials via Two-Step Sintering

Issues in nanocomposite ceramic engineering: focus on processing and properties of alumina-based composites

Effects of Adding Methods of YAG on Sintering Behaviour, Mechanical Properties and Microstructure of SiC Ceramic