Abstract:Research highlights ► In this paper, in order to clarify the nature of some phase transitions and origin of inelastic information, we carried out an investigation on the mechanical properties of La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ (0 ≤ x ≤ 0.8) materials by using low frequency internal friction technique. The results show that the inelastic deformation of La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ materials can be understood in virtue of the motion of domain walls, and domains were formed during the cubic–rhombohedral phase transition. Below the ferromagnetic ordering temperature T C , La 0.6 Sr 0.4 CoO 3− δ system presents a phase transition, which is related to magnetization intrinsic phase separation. Abstract The low-frequency mechanical properties of La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ (0 ≤ x ≤ 0.8) materials have been measured using a computer-controlled pendulum. For undoped sample, five internal friction peaks (P0, P1, P2, P3 and P4) were observed. However, with the Fe doping, only two peaks (P3 and P4) were found at high temperature. The peaks of P0 and P1 have the feature of phase transition-induced internal friction, while the peaks of P2, P3 and P4 are the relaxation-type. From the analysis, it is suggested that the peak of P0 is due to the phase separation and the peak of P1 is related to the ferromagnetic (FM)–paramagnetic (PM) phase transition. For the peaks of P2, P3 and P4, they were associated with the motion of domain walls. The formation of this kind of domain structure is a consequence of a transformation from the paraelastic cubic phase to ferroelastic rhombohedral phase. PACS 62.40.+I 61.72.Hh 75.60.−d Keywords Ceramics Mechanical properties Phase transitions Domain structure 1 Introduction LaCoO 3 -based materials have attracted considerable attention because of their fascinating physical phenomenon such as spin-state transition [1] , and magnetic phase separation [2–8] , as well as their potential materials as oxygen permeable membranes [9] . The parent compound LaCoO 3 has a rhombohedrally distorted pseudo-cubic structure with the space group R 3 ¯ c . This distortion decreases monotonically with the strontium doping in La 1− x Sr x CoO 3 , and the structure becomes cubic when x = 0.6 [10] . The magnetic properties of this system are also strongly dependent on the strontium content. At low doping level, the La 1− x Sr x CoO 3 system runs into a spin-glass phase, when x ≥ 0.2, this system becomes ferromagnetically ordered [2–4] . However, some evidences suggest that even below the ferromagnetic ordering temperature T C , the system is still a cluster-glass phase with short range ferromagnetic ordering [5–7] . Recently, the attention of researchers was concentrated on the ferroelasticity of the LaCoO 3 -based system [11–18] . But till now, its origin is still in discussion. By means of in situ transmission electron microscopy (TEM) during thermal cycles, different types of structural features of LaCoO 3 -based materials, such as twins and antiphase domains have been observed by Orlovskaya et al. The domain motion and de-twinning during heating, and the reappearance of twins during cooling may be responsible for ferroelastic behavior [14] . Vullum et al. also confirmed this conclusion by the measurement of in situ synchrotron X-ray diffraction [15] . However, although similar ferroelastic behavior has been found in La 0.6 Sr 0.4 FeO 3 , Orlovskaya et al. suggested that this behavior originates from the phase transformation and/or dislocation motion since no domain/twin structure was observed [19] . As a systematic tool, the internal friction technique has been proven to be particularly successful in investigating the microscopic relaxation processes and phase transitions in solid materials [20–25] . To gain more insight into the microscopic origin of the inelasticity and phase transition in LaCoO 3 -based materials, the low-frequency mechanical properties of La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ (0 ≤ x ≤ 0.8) are investigated in this paper. Furthermore, the measurements of resistivity and magnetization are also carried out to clarify the nature of the internal friction peaks. 2 Experimental procedure La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ (0 ≤ x ≤ 0.8) powders were prepared via a citrate route. Two aqueous solutions of iron nitrate and cobalt nitrate were firstly prepared and analyzed by titrations to determine the concentration of Fe and Co ions. Then these solutions were mixed together with the appropriate amounts of La 2 O 3 (99.9%) and SrCO 3 (>99.0%), which were both completely dissolved by adding diluted nitric acid. After forming a clear solution, citric acid was added at a molar ratio of citric acid: metal ions = 1.5:1.0, followed by adjusting the pH value to 2–3. The solution was subsequently stirred and evaporated at 80 °C until a formation of polymeric precursor, which was ignited in air to remove the organic contents. The resulting ash was ground to fine powders and calcined at 1050 °C in air for 5 h. The obtained powders were uniaxially pressed into bars at 150 MPa, subsequently isostatically pressed at 300 MPa and sintered in air at 1250 °C for 10 h. Since the crystal structure of La 1− y Sr y Co 1− x Fe x O 3− δ is dependent on cooling rate [26] , in order to obtain purely rhombohedral phase sample, the cooling rate of 1 K/min is adopted. The crystal structure of the calcined powders was characterized by XRD (Philips X’Pert Pro Super, Cu Kα). The electrical resistivity was measured by standard four-probe technique. The zero-field-cooled (ZFC) magnetization was measured in an external magnetic field of 100 Oe using a commercial quantum device (superconducting quantum interference device; Quantum Design MPMSXL). The internal friction and shear modulus were measured in a computer-controlled automatic inverted torsion pendulum using the forced-vibration method with the maximum torsion strain amplitude kept at 1.5 × 10 −5 at a heating rate of 2 K/min from 120 K to 650 K. 3 Experimental results and discussion The X-ray diffraction patterns of La 0.6 Sr 0.4 Co 1− x Fe x O 3− δ ( x = 0, 0.1, 0.2, 0.3, 0.5, 0.8) are shown in Fig. 1 . All the samples crystallize in single phase and exhibit a rhombohedrally distorted perovskite structure with R 3 ¯ c symmetry, which is in accordance with the earlier studies [6] . Fig. 2 presents the temperature dependence of internal friction Q −1 and shear modulus M for La 0.6 Sr 0.4 CoO 3− δ . Four internal friction peaks are readily observed and marked as P0, P2, P3 and P4, which locate at about 180, 320, 440, and 505 K. Besides these peaks, another small shoulder peak is also found which locates at the low temperature side of P2 and is marked as P1 (255 K). For P0 and P1, their positions do not shift with increasing the frequency, which reveals that the two peaks are both phase transition-induced internal friction peaks. However, the peaks of P2, P3 and P4 are of relaxation type, since their peak temperature shifts to higher temperature with increasing the frequency. For the peaks of P0 and P1, from the earlier reports, no structure phase transitions have been observed in this temperature range. So there should be other reasons for these two peaks. In order to clarify the origin of the peaks of P0 and P1, the measurements of the magnetic and electric transport properties were carried out. The results are shown in Fig. 3 . It can be seen that the ZFC magnetization rises sharply at around 250 K, corresponding to a PM–FM phase transition, and then undergoes a less rapid drop down to 40 K. However, the resistivity shows a monotonic descending, and only a slope change is seen at the Curie temperature T c , which is regarded as a result of spin–disorder scattering. These results agree well with the earlier reports [6] . Combined with the results of magnetization and resistivity as shown in Fig. 3 , the peak of P1 at 255 K is suggested to be related with the magnetic transition, while the origin of the peak of P0 is still unclear. Therefore, we considered other alternative mechanisms which could cause this internal friction peak. According to the phase diagram of La 1− x Sr x CoO 3 [3,8] , it is postulated that in the low doping region ( x < x m , x m ∼ 0.2), the sample separates into hole-rich ferromagnetic clusters and hole-poor nonferromagnetic matrix. The former is dominated by the ferromagnetic double exchange interaction between Co 3+ and Co 4+ , and the latter is dominated by the antiferromagnetic (AF) superexchange interaction between Co 3+ and Co 3+ . Furthermore, the ferromagnetic clusters are embedded in the nonferromagnetic matrix, and the competition between the ferromagnetic and the antiferromagnetic interactions along with the randomness lead to spin glass (SG) states. With increasing the x , the ferromagnetic double-exchange interaction is enhanced, and these ferromagnetic clusters eventually coalesce, leading to the appearance of the cluster glass phase with short range ferromagnetic ordering ( x m < x < 0.50). According to this phase diagram, our sample La 0.6 Sr 0.4 CoO 3− δ should belong to the cluster glass phase. In fact, this coexistence of two phases has been experimental confirmed by Kuhns et al. [8] . In manganites, it is known that this kind of phase coexistence always leads the internal friction peak [24,25] . Thus, it is highly possible that the peak of P0 may originate from the phase separation. With the substitution of Fe ions for Co ions in La 0.6 Sr 0.4 Co 1− x Fe x O 3 , some different low frequency mechanical behaviors are observed. Figs. 4 and 5 show the results of the samples ( x = 0.1, 0.2), respectively. It can be seen that the peaks of P2, P3 and P4 still exist at the corresponding temperature range. But the peaks of P0 and P1 cannot be readily found. With increasing the Fe content, the peak of P2 is disappeared. The curves of Q −1 ( T ) and M ( T ) for the samples ( x = 0.3, 0.5 and 0.8) are, respectively, shown in Figs. 6–8 . Three compositions exhibit the similar low-frequency mechanical behaviors. Only one peak is readily observed, and at high temperature side of this peak, an obvious abnormity is found, which suggests the existence of another peak. Compared with the curves in Figs. 2–5 , the former corresponds to the peak of P3, and the latter is related to the peak of P4. Compared with the peaks of P0 and P1, the other three peaks (P2, P3 and P4) are much broader in the curves of Q −1 ( T ), implying they have a fully different origin. As we known, it has been reported that LaCoO 3 -based perovskites exhibit a nonlinear stress–strain relationship and inelastic deformation behavior [11–17] . For our investigated La 0.6 Sr 0.4 Co 1− x Fe x O 3 system, at high temperature, the lattice structure of La 0.6 Sr 0.4 Co 1− x Fe x O 3 system is cubic symmetry. When decreasing temperature to a critical point (for La 0.6 Sr 0.4 CoO 3 , about 673 K [29] ), the system undergoes a transition from cubic to rhombohedral symmetry, driven by rotation of the Co(Fe)O 6 -octahedra about one of the cubic three-fold symmetry axis. Due to the choice of four equivalent triad axes, transformation twin domains can be formed, which have been confirmed by the transmission electron microscopy [14] . The combination of structure changes and the appearance of transformation twins result in a rapid softening in modulus even in small applied forces. Low-frequency internal friction measurement on La 1− x Sr x FeO 3 has demonstrated this point [20,21] . The inelastic deformation of LaCo(Fe)O 3 based perovskites may associated with the structure phase transition and the appearance of transformation twins. In many ferroelectric ceramics, the motion of the domain walls leads to the relaxation internal friction peaks [27,28] . Thus, the similar feature may be response to the three peaks (P2–P4) in our samples. The domain forms during phase transition, and when the temperature is high enough, thermal energy is sufficient to allow these domain walls to move under small applied forces. This is accompanied by an increase in Q −1 (P4 peak), as energy is dissipated by moving domain walls against the force exerted by lattice defects. Moreover, Peierls force associated with moving a wall of finite thickness through a discrete lattice may also contribute small part to this peak [27] . With the temperature decreasing, thermal energy is so low that it is not enough to overcome the interactions between oxygen vacancies and domain walls. Thus these domain walls become immobile. This freezing of the domain walls is anelastic and would lead to the pronounced resonance peak [20,21] . This phenomenon is very similar to those of LaAlO 3 [30] and Ca 1− x Sr x TiO 3 [31] reported by Harrison. In fact, in the LaCoO 3 -based perovskites, different types of domains have been confirmed by the in situ TEM measurement, such as short parallel domains oriented at 180° to each other and long domains [14] . Upon heating, the 180° domains are found to be the most unstable and mobile, but other long domains are still stable. Therefore, it is suggested that the peaks of P2 and P3 may originate from the movement of the different domain walls. Since the ionic radius of Fe ions is larger than that of Co ions, its substitution involves a tilting of the octahedron and increases the distortion of the perovskite cell. It is known that the formation of the transformation twins and domain originates from the choice of four equivalent triad axes that the octahedral rotation could occur. Thus the tilting of the octahedron may have significant effect on the formation of domain state, leading to the different microstructure. In fact, in the La 0.6 Sr 0.4 FeO 3 , no domains, twins, antiphase boundaries, stacking faults, and other planar defects are observed [19] , which is different to the LaCoO 3 based perovskites. Thus in the higher Fe-doping samples, different mechanical response is observed, and it can be seen that the peak of P2 disappears. However, it should be mentioned that the effect of Fe doping on the formation of the transformation twins and domain is still under discussion. Different conclusions have been drawn through different experimental conditions. For example, recently, the micro-structural evidence of domains in the rhombohedral La 0.58 Sr 0.4 Co 0.2 Fe 0.8 O 3− δ sample is confirmed by the SEM and TEM observations [26] . Thus, more detailed studies are needed to further clarify the nature of the domain walls. 4 Conclusion At most five internal friction peaks are observed depending on Fe content in the La 0.6 Sr0 .4 Co 1− x Fe x O 3− δ perovskites: three are relaxation peaks and two are phase transition type peaks. In addition to the peak of P1 correlated with PM–FM transition, the peak of P0 located below T c is suggested to originate from the phase separation. At higher temperature, the system undergoes a transition from cubic to rhombohedral phase on cooling, accompanied by the formation of transformation twins. These relaxation peaks should be related to the motion of domain walls. The ferroelastic behavior of the Fe-doped La 0.6 Sr 0.4 CoO 3 may associate with the structure transition and the motion of the domain walls. Acknowledgments The research was supported by National Natural Science Foundation of China (Grant Nos. 10574123 and 11004002 ), the Key Program of Scientific Research Fund of Anhui Provincial Education Department (No. KJ2008A018 ) and the doctoral initial funding of Anhui University of Architecture (2008). References [1] C. Zobel M. Kriener D. Bruns J. Baier M. Gruninger T. Lorenz P. Reutler A. Revcolevschi Phys. Rev. B 66 2002 020402(R)-1–4 [2] M. Itoh I. Natori S. Kubota K. Motoya J. Phys. Soc. Jpn. 63 1994 1486 1493 [3] M.A. Senaris-Rodriguez J.B. Goodenough J. Solid State Chem. 118 1995 323 336 [4] M.J.R. Hoch P.L. Kuhns W.G. Moulton A.P. Reyes J. Wu C. Leighton Phys. Rev. B 69 2004 014425-1 014425-7 [5] S. Mukherjee R. Ranganathan P.S. Anilkumar P.A. Joy Phys. Rev. B 54 1996 9262 9274 [6] J. Wu C. Leighton Phys. Rev. B 67 1999 174408-1 174408-16 [7] R. Caciuffo D. Rinaldi G. Barucca J. Mira J. Rivas M.A. Señarís-Rodríguez P.G. Radaelli D. Fiorani J.B. Goodenough Phys. Rev. B 59 1999 1068 1078 [8] P.L. Kuhns M.J.R. Hoch W.G. Moulton A.P. Reyes J. Wu C. Leighton Phys. Rev. Lett. 91 2003 127202-1 127202-4 [9] H.J.M. Bouwmeester Solid State Ionics 82 2003 141 150 [10] A.N. Petrov O.F. Kononchuk A.V. Andreev V.A. Cherepanov P. Kofstad Solid State Ionics 80 1995 189 199 [11] N Orlovskaya K. Kleveland T. Grande M.-A. Einarsrud J. Eur. Ceram. Soc. 20 2000 51 56 [12] K. Kleveland N. Orlovskaya T. Grande A.M.M. Moe M.A. Einarsrud K. Breder G. Gogotsi J. Am. Ceram. Soc. 84 2001 2029 2033 [13] N. Orlovskaya Y. Gogotsi M. Reece B. Cheng I. Gibson Acta Mater. 50 2002 715 723 [14] N. Orlovskaya N. Browning A. Nicholls Acta Mater. 51 2003 5063 5071 [15] P.E. Vullum J. Mastin J. Wright M.A. Einarsrud R. Holmestad T. Grande Acta Mater. 54 2006 2615 2624 [16] N. Orlovskaya D. Steinmetz S. Yarmolenko D. Pai J. Sankar J. Goodenough Phys. Rev. B 72 2005 014122-1 014122-7 [17] S. Faaland T. Grande P.E. Vullum R. Holmestad M.-A. Einarsrud J. Am. Ceram. Soc. 88 2005 726 730 [18] N. Orlovskaya M. Lugovy S. Pathak D. Steinmetz J. Lloyd L. Fegely M. Radovic E.A. Payzant E.L. Curzio L.F. Allard J. Kuebler J. Power Sources 182 2008 230 239 [19] N. Orlovskaya H. Anderson M. Brodnikovskyy M. Lugovy M.J. Reece J. Appl. Phys. 100 2006 026102-1 026102-3 [20] X.S. Wu Y.B. Zuo J.H. Li C.S. Chen W. Liu J. Alloys Compd. 462 2008 432 435 [21] X.S. Wu C.L. Yang Z.J. Chen C.S. Chen W. Liu Acta Phys. Sin. 9 2009 6419 6425 (in Chinese) [22] W.L. Warren K. Vanheusden D. Dimos G.E. Pike B.A. Tuttle J. Am. Ceram. Soc. 79 1996 536 538 [23] X.P. Wang Q.F. Fang Phys. Rev. B 65 2002 064304-1 064304-6 [24] Y.Q. Ma W.H. Song R.L. Zhang J.M. Dai J. Yang J.J. Du Y.P. Sun C.Z. Bi Y.J. Ge X.G. Qiu Phys. Rev. B 69 2004 134404-1 134404-6 [25] W.J. Lu Y.P. Sun B.C. Zhao X.B. Zhu W.H. Song Phys. Rev. B 73 2006 214409-1 214409-6 [26] B.X. Huang J. Malzbender R.W. Steinbrech E. Wessel H.J. Penkalla L. Singheiser J. Membr. Sci. 349 2010 183 188 [27] Y.N. Wang Y.N. Huang H.M. Shen Z.F. Zhang J. Phys. IV 6 Colloque C8, Suppl. to J. Phys. III 1996 505 514 [28] J.A. Bartkowska J. Bluszcz R. Zachariasz J. Milczuk B. Brus J. Phys. IV Fr. 137 2006 19 21 [29] S.R. Wang M. Katsuki M. Dokiya T. Hashimoto Solid State Ionics 159 2003 71 78 [30] R.J. Harrison S.A.T. Redfern Phys. Earth Planet. Int. 134 2002 253 272 [31] R.J. Harrison S.A.T. Redfern J. Street Am. Mineral. 88 2003 574 582

Abstract:The longitudinal ultrasonic velocity ( V l ), as well as resistivity has been measured in single-phase polycrystalline La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) at a frequency of 10 MHz, from 20 K to 300 K. It is found that with increasing Mn-doping level, the resistivity increases and the charge ordering transition temperature T CO shifts to lower temperature. For all samples, upon cooling down from 300 K, a substantial softening in V l above T CO and dramatic stiffening below T CO are observed. This abnormal elastic softening above T CO can be described well by the mean-field theory, which indicates that this feature is due to the electron–phonon coupling via the Jahn–Teller effect and this coupling is enhanced with the Mn doping. Below T CO , another softening in V l is observed for x = 0, and weakens with the increasing of Mn content. This character is attributed to the breathing-type distortion of Fe–O octahedron and suggests that the charge disproportionation (CD) transition is suppressed by the Mn substitution. PACS 62.80.+f 71.38.−k 75.30.Kz Keywords Rare earth compounds and compounds Oxide materials Electron–phonon interaction Ultrasonic 1 Introduction The perovskite-type transition-metal oxides have attracted much attention due to their particular structural, electronic and magnetic properties. Besides the well-known colossal magnetoresistance effect (CMR) [1] , another interesting phenomenon is the real-space ordering of charge carriers [2] . Among the charge ordering (CO) systems, La 1/3 Sr 2/3 FeO 3 has attracted considerable attention because its CO accompanies both antiferromagnetic (AFM) spin ordering and charge disproportionation (CD) of 2Fe 4+ → Fe 3+ + Fe 5+ [3,4] . And in its ordering state, a sequence of …Fe 3+ Fe 3+ Fe 5+ Fe 3+ Fe 3+ Fe 5+ … exists along the [1 1 1] direction of the pseudocubic perovskite unit cell [5] . The most novel feature in La 1/3 Sr 2/3 FeO 3 is the high valence state of Fe:Fe 4+ and Fe 5+ . For Fe 4+ (d 4 ), it is isoelectronic with Mn 3+ . From previous works, it has been widely recognized that the Jahn–Teller distortion of Mn 3+ , plays an important role for the CO state in manganites [6] . Thus the similar lattice distortion is expected in La 1/3 Sr 2/3 FeO 3 . And for Fe 5+ , it occupies smaller octahedral sites than Fe 3+ , which would results in the breathing-type distortion of Fe–O octahedron. In fact, the difference of the Fe–O bond lengths was found in the charge disproportionation transition of CaFeO 3 , which is higher than 0.1 Å [7] . However, the existence of these two kinds of lattice distortion in La 1/3 Sr 2/3 FeO 3 is still under discussion. Different conclusions have been drawn through different experimental and theoretical tools, which are summarized as follows. First, no structural changes accompany the CO–CD transition. This point was supported by the neutron powder diffraction results [5] . And unrestricted Hartree–Fock band-structure calculations have also suggested that this charge ordering can be driven by purely electronic interactions [8] . Second, only the breathing-type distortion of Fe–O octahedron exists below T CO . This explanation was based on the fact of the superlattice spots, which have been detected by the transmission electron microscopy below T CO [3] . Ishikawa also confirmed this distortion by the measurement of optical spectroscopy [9] . Third, the lattice distortions are present only above T CO . In 2005, Ghosh et al. indicates this result from the temperature-dependent micro-Raman study [10] . From these works, it can be seen that the physical nature for this threefold CO–CD phase is still controversial. And the attention of researchers was mainly concentrated on the question: whether this transition is accompanied by any lattice distortions? Thus, a detailed revelation of the interplay between the lattice dynamics and the CO–CD transition in La 1/3 Sr 2/3 FeO 3 remains to be resolved and more experimental tools and results are needed. The ultrasonic technique is a sensitive tool for studying the lattice distortion and has been successfully employed to study the CO state in manganites [6] and the CO–CD transition in La 1/3 Sr 2/3 FeO 3 [11,12] . This technique provided new evidence to support the two kinds of lattice distortion in the CO–CD process. However, this conclusion needs more experimental supports. Since the high-valence state of Fe 5+ in La 1/3 Sr 2/3 FeO 3 is stabilized by the strong hybridization with O 2 p bands [9] , its stability is very sensitive to the surrounding environment. So the B-site doping effect is believed to provide important clues to the nature of the CO–CD transition [12] . In this paper, we report our systematic studies of the longitudinal ultrasonic velocity ( V l ) as a function of temperature in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) with an aim to gain more insight into the microscopic origin of CO–CD transition. 2 Experimental procedure The polycrystalline samples of La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) were prepared by a solid-state reaction method. Stoichiometric amount of high purity La 2 O 3 , SrCO 3 , MnCO 3 and Fe 2 O 3 powders were well mixed, ground and calcinated at 1100°, 1150°, 1200° in air for 15 h. The final obtained powder was then pressed into pellets at 300 MPa and sintered at 1200° in air for 20 h. The crystal structure was characterized using a Japan Rigaku MAX-RD powder X-ray diffractometer with Cu Kα radiation ( λ = 1.5418 Å) at room temperature. The resistivity was measured by the standard four-probe technique. The longitudinal ultrasonic velocity measurement was performed on the Matec-7700 series by means of a conventional pulsed echo technique. All experiments were taken in a closed-cycle refrigerator during the warm-up from 20 to 300 K at the rate of about 0.25 K/min. Temperature was measured with an Rh–Fe resistance thermometer. The estimated error on temperature is ±0.1 K. The relative change of the longitudinal sound velocity Δ V l /V l min in Fig. 3 was defined according to the following equation: (1) Δ V l V l min = V l − V l min V l min where V l min (m s −1 ) is the minimal longitudinal sound velocity in the temperature range from 20 K to 300 K. 3 Experimental results and discussion The X-ray diffraction patterns of La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) are shown in Fig. 1 . All samples are of single phase with no detectable secondary phases. The diffraction peaks are sharp and can be indexed with the space group R 3 ¯ c in the hexagonal setting, which are consistent with other reports [4] . Fig. 2 (a) exhibits the temperature dependence of resistivity for La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05). All samples show semiconductor-like transport behavior in the whole temperature range, which increases slightly with Mn doping, and exhibit a discernible slope change around the T CO . To study the evolution of CO transition in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 , the d(ln ρ )/d( T −1 ) − T curves were plotted in the Fig. 2 (b). All curves show an abnormal peak, and according to the previous studies, the T CO can be defined as the corresponding peak temperature [13] . It can be seen that with increasing Mn doping level, the CO state becomes unstable: the T CO shifts to lower temperature, and the peak of d(ln ρ )/d( T −1 ) is broadened. Furthermore, the peak value of d(ln ρ )/d( T −1 ) decreases from more than 6000 in the Mn-free sample to about 2000 in x = 0.05 sample. This behavior is due to the substitution of Mn 3+ for Fe 3+ . The doped Mn acts as an impurity, inducing disorder and hindering the establishing of antiferromagnetic charge ordering state. The similar disorder effect has been well discussed in charge-ordered manganites [14] . Fig. 3 shows the temperature dependence of the longitudinal ultrasonic velocity ( V l ) at a frequency of 10 MHz for La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05). In all samples, the V l softens smoothly as the temperature decreasing from 300 K and substantially increases below T CO , which exhibits a valley around T CO . Below 181 K, the V l of La 1/3 Sr 2/3 FeO 3 shows another unexpected softening and resumes normal increase at about 70 K. With Mn doping, this anomaly weakens and finally disappears for x = 0.05. It is well known that in the normal state, the ultrasonic velocity increases with the temperature decreasing. Thus the origin of these two kinds of velocity softening needs explanations. As is known, the charge-ordering transition in La 1/3 Sr 2/3 FeO 3 is accompanied by the AFM transition. Thus, the first consideration of the origin of the ultrasonic anomaly around T CO is the magnetic transition. According to the Landau–Khalatnilov theory, the relative velocity change (Δ V / V ) caused by a typical AFM spin fluctuations is of the order 0.1% [15] . However, in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 , the Δ V / V around T CO is more than 3%, which is much larger than that caused by an AFM phase transition. These results indicate that there is a strong electron–phonon coupling in this system. In fact, the similar phenomenon has been well discussed in charge-ordered manganites on both experimental and theoretical levels [6,16] , which is interpreted by the electron–phonon coupling originated from the Jahn–Teller effect of Mn 3+ . Thus it is reasonable to attribute this ultrasonic anomaly in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 to the similar electron–phonon coupling. However, the question is: which kind of transition-metal ions is Jahn–Teller active? In La 1/3 Sr 2/3 Fe 1− x Mn x O 3 , Mn 3+ is the first candidate for the Jahn–Teller effect. However, in x = 0 sample, no Mn 3+ exist, which suggests that the Mn 3+ could not response to the ultrasonic anomalies in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 alone. Thus the Fe ions should be considered. For Fe ions, the experimental results showed that its valence states are +3 and +4 above T CO [4] . The ground state of Fe 3+ is high-spin t 2g 3 e g 2 with two unpaired electrons filling the e g band, which means Fe 3+ does not necessarily remove the degeneracy to low its symmetry. So it is not Jahn–Teller active. For Fe 4+ , due to its unconventionally high valence, the electronic structure is rather unique. It is isoelectronic with Mn 3+ and its charge-transfer energy Δ is quite negative, which implies that a large amount of charges are transferred via Fe–O bonds from the O 2 p bands to the Fe d orbits. Thus the Fe 4+ state is a mixture of 3d 4 and 3d 5 L [17] , where L denotes a hole in the O 2 p band, and the 3d 4 state may be Jahn–Teller active. To clarify the relationship between the ultrasonic anomaly and Jahn–Teller effect, the ultrasonic velocity data were analyzed by the Jahn–Teller theory, which describes the coupling of the Jahn–Teller ions to the lattice distortion under the mean field approximation. According to this theory, the relationship between the longitudinal modulus C l ( T ) and temperature T ( T > T CO ) can be written as [18] : (2) C l ( T ) = C 0 T − T c 0 T − Θ where C l = DV l 2 [19] , with D is the mass density, C 0 is the elastic modulus in the absence of Jahn–Teller coupling of the lattice with the electronics state of the ions, and the characteristic temperature of T C 0 and Θ can be determined by the ultrasonic measurements of the elastic modulus softening. The Jahn–Teller coupling energy E JT is obtained by the formula [ E JT = T C 0 − Θ ] . Eq. (2) can be used to fit the experimental data of the elastic softening above T CO , and is proven in charge-ordered manganites [20] and R 1/3 Sr 2/3 FeO 3 (R = La, Pr, Gd) [21] . The temperature dependence of C l for La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) is plotted in the inset of Fig. 3 . The open symbols are the experimental data and the solid line is the theoretical result (the values of the T C 0 , Θ, C 0 / C min are 49.55 K, 39.69 K, 1.066 for x = 0 sample, 51.29 K, 38.88 K, 1.090 for x = 0.025 sample, and 53.15 K, 39.69 K, 1.114 for x = 0.05 sample). The good agreement between experiment and theory indicates that the electron–phonon coupling via the Jahn–Teller effect indeed exists in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 samples. And from this theoretical calculation results, it can be seen that the E JT of x = 0, x = 0.025 and x = 0.05 samples are 9.86 K, 12.41 K and 13.46 K respectively. The increase of E JT as Mn content increasing reflects that the coupling of Jahn–Teller effect becomes stronger. Below T CO , another equation can be used to describes the relationship between the C l ( T ) and temperature T ( T < T CO ) [18] , which is already applied to the charge-ordered manganites [14] . However, in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 system, the CD transition occurs below T CO , and the interplay among different valence states of iron (Fe 3+ , Fe 4+ , Fe 5+ ) makes this quantitative equation invalid. Thus, to prove that the hardening of V l below T CO also originates from the Jahn–Teller effect, two theoretical qualitative results are applied to the La 1/3 Sr 2/3 Fe 1− x Mn x O 3 samples. First, based on the Hamiltonian of small Jahn–Teller polarons with strong electron–phonon coupling, Min et al. found that in manganites, the CO interaction induces the softening of V l above T CO and the hardening below T CO [16] , which is proven in the charge-ordered manganites [6,14] . Their calculation result is qualitatively similar to our observation. Second, from earlier studies in manganites, the relative stiffening of the ultrasonic velocity can be viewed as a scale of the development of the Jahn–Teller effect [6] . And this conclusion was proved in the in the low Sr-doping La 1− x Sr x FeO 3 [22] , which corresponds to the short-range charge ordering state of Fe 3+ and Fe 4+ . So if the Jahn–Teller effect indeed exists in the La 1/3 Sr 2/3 Fe 1− x Mn x O 3 samples during the CO transition, the increase of E JT as Mn content increasing according to the Eq. (2) would lead to more sound velocity increase below T CO . This prediction was proven from the Fig. 3 . It can be seen that the relative stiffening of V l below T CO indeed becomes larger with increasing Mn content. For example, the relative stiffening change of V l in x = 0 sample is only 3%, while it reaches more than 5% in x = 0.05 sample. Based on the upper discussions, it can be seen that the hardening of V l below T CO in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 samples is consistent with the qualitative theories, which implies that it may also originate from the Jahn–Teller effect. It is worth mentioned that both the quantitative calculation of the elastic softening above T CO and qualitative analysis of the velocity hardening below T CO show that with the Mn content increasing, the E JT increases. This behavior is probably due to the following two reasons. On the one hand, the Mn 3+ is also Jahn–Teller active. Furthermore, the Jahn–Teller effect of Mn 3+ is much more than that of Fe 4+ . For example, in La 1/3 Sr 2/3 MnO 3 , the relative ultrasonic stiffening change is more than 15% [11] , and in some charge ordered manganites, the resulting structure change can be detected by the XRD measurement [23] . So its doping would enhance the Jahn–Teller effect. On the other hand, the doped Mn ion acts as an impurity, making the Fe 5+ unstable. It is known that the charge disproportionation of 2Fe 4+ → Fe 3+ + Fe 5+ occurs below T CO , and this transition decreases the content of high-spin Fe 4+ . For Fe 5+ , due to its unconventionally high valence, it is stabilized via the strong p – d hybridization between oxygen 2 p σ and Fe 3 d e g states. From the earlier studies, it is known that the electronegativity of Mn (1.55) is smaller than that of Fe (1.83). So the substitution of Mn increases the electronegativity difference between B-site ion and oxygen, and increases the ionic characteristic of the B–O bond. This feature results in the shift of the intermediate oxygen towards Mn 3+ and weakens the hybridization between O 2− and Fe 5+ , which makes the Fe 5+ unstable. Thus the Mn doping would suppress the CD transition and more Fe 4+ would exist below T CO , which leads to the more velocity stiffening. If this deduction is true, this suppression would also decrease the fraction of Fe 5+ below T CO and weaken the breathing-type distortion. To verify this prediction, we focus on the ultrasonic behavior of La 1/3 Sr 2/3 Fe 1− x Mn x O 3 below T CO in Fig. 3 . Below T CO , another unexpected softening in V l of La 1/3 Sr 2/3 FeO 3 was observed. From previous reports, it is known that this velocity softening below T CO originates from the breathing type distortion [11,20] . This distortion arises from the fact that Fe 5+ cations will occupy smaller octahedral sites than Fe 3+ cations, and was confirmed by the measurements of transmission electron microscopy [3] and optical spectroscopy [9] . So if the Mn doping indeed suppresses the charge disproportionation in La 1/3 Sr 2/3 FeO 3 , this breathing-type distortion would be weakened. For example, in La 1/3 Sr 2/3 Fe 1− x Co x O 3 , the softening in V l below T CO weakens with the Co doping [12] . Accompanying this variation, the Mössbauer spectroscopy measurement indicates that the fraction of Fe 5+ decreases from 33% in La 1/3 Sr 2/3 FeO 3 at 20 K [4] to 17% in La 1/3 Sr 2/3 Fe 0.85 Co 0.15 O 3 at 15 K [24] . From Fig. 3 , it can be seen that the ultrasonic softening below T CO weakens with the Mn doping and finally disappears at x = 0.05. This feature is consistent with our analysis and implies that the Mn doping indeed suppress the CD transition. However, the Mössbauer spectroscopy results would be valuable to further clarify the evolution of this transition. Based on the upper discussions, it can be seen that the Mn doping not only enhances the Jahn–Teller effect, but also suppresses the CD transition. Both these effects lead to more sound velocity increasing below T CO . 4 Conclusion In conclusion, we have systemically studied the ultrasonic properties of polycrystalline La 1/3 Sr 2/3 Fe 1− x Mn x O 3 ( x = 0, 0.025, 0.05) to clarify the Mn doping effect on the CO–CD transitions. It is found that the Mn substitution increases the resistivity and T CO shifts to lower temperature. Dramatic softening in V l above T CO is observed in all samples, which can be described well by the mean-field theory. Below T CO , another softening in V l is observed for x = 0, and weakens as the Mn content increases. These results indicate that two kinds of lattice distortion exist in La 1/3 Sr 2/3 Fe 1− x Mn x O 3 samples. The first is the distortion arising from the Jahn–Teller effect of high-spin Fe 4+ , which is present around T CO and leads to the softening in V l above T CO and the stiffening below T CO . When the CD transition occurs, the Fe 4+ gradually changed to Fe 3+ and Fe 5+ , and the Jahn–Teller type distortion was replaced by the breathing-type distortion, which results in another softening in V l at low temperature. With the Mn doping, the E JT increases and the charge disproportionation transition is suppressed. The former increases the velocity stiffening below T CO , and the latter weakens the ultrasonic softening at low temperature. These results are helpful to understand the relationship between the electron–phonon interaction and the CO–CD transitions. Acknowledgments This work was supported by the National Natural Science Foundation of China (No. 10774136 and No. 11004002 ) and the Key Program of Scientific Research Fund of Anhui Provincial Education Department (No. KJ2008A018 ). References [1] R. von Helmolt J. Wecker B. Holzapfel L. Schultz K. Samwer Phys. Rev. Lett. 71 1993 2331 2333 [2] C.N.R. Rao B. Raveau Colossal Magnetoresistance, Charge Ordering and Related Properties of Manganese Oxides 1998 World Scientific Singapore [3] J.Q. Li Y. Matsui S.K. Park Y. Tokura Phys. Rev. Lett. 79 1997 297 300 [4] J.B. Yang X.D. Zhou Z. Chu W.M. Hikal Q. Cai J.C. Ho D.C. Kundaliya W.B. Yelon W.J. James H.U. Anderson H.H. Hamdeh S.K. Malik J. Phys.: Condens. Matter 15 2003 5093 5102 [5] P.D. Battle T.C. Gibb P. Lightfoot J. Solid State Chem. 84 1990 271 279 [6] R.K. Zheng G. Li Y. Yang A.N. Tang W. Wang T. Qian X.G. Li Phys. Rev. B 70 2004 014408 014414 [7] P.M. Woodward D.E. Cox E. Moshopoulou A.W. Sleight S. Morimoto Phys. Rev. B 62 2000 844 855 [8] J. Matsuno T. Mizokawa A. Fujimori K. Mamiya Y. Takeda S. Kawasaki M. Takano Phys. Rev. B 60 1999 4605 4608 [9] S.K. Park T. Ishikawa Y. Tokura J.Q. Li Y. Matsui Phys. Rev. B 60 1999 10788 10795 [10] S. Ghosh N. Kamaraju M. Seto A. Fujimori Y. Takeda S. Ishiwata S. Kawasaki M. Azuma M. Takano A.K. Sood Phys. Rev. B 71 2005 245110 245116 [11] H. Kong C. Zhu Appl. Phys. Lett. 88 2006 041920 041922 [12] H. Kong Y. Liu C. Zhu J. Alloys Compd. 429 2007 60 63 [13] A.P. Ramirez P. Schiffer S.-W. Cheong C.H. Chen W. Bao T.T.M. Palstra P.L. Gammel D.J. Bishop B. Zegarski Phys. Rev. Lett. 76 1996 3188 3191 [14] H.-D. Zhou G. Li H. Chen R.-K. Zheng X.-J. Fan X.-G. Li J. Phys.: Condens. Matter 13 2001 6195 6202 [15] D. Berlincourt H. Jaffe Phys. Rev. 111 1958 143 148 [16] B.I. Min J.D. Lee S.J. Youn J. Magn. Magn. Mater. 171 1998 881 883 [17] M. Abbate F.M.F. de Groot J.C. Fuggle A. Fujimori O. Strebel F. Lopez M. Domke G. Kaindl G.A. Sawatzky M. Takano Y. Takeda H. Eisaki S. Uchida Phys. Rev. B 46 1992 4511 4519 [18] R.L. Melcher W.P. Maston R.N. Thurston Physical Acoustics vol. 12 1970 Academic New York 1 21 [19] M. Cankurtaran G.A. Saunders K.C. Goretta R.B. Poeppel Phys. Rev. B 46 1992 1157 1165 [20] T. Qian R.K. Zheng T. Zhang T.F. Zhou W.B. Wu X.G. Li Phys. Rev. B 72 2005 024432 024438 [21] H. Kong C. Zhu Europhys. Lett. 86 2009 54001 54005 [22] H. Kong C. Zhu J. Phys.: Condens. Matter 20 2008 115211 115214 [23] X.-G. Li H. Chen C.F. Zhu H.D. Zhou R.K. Zheng J.H. Zhang L. Chen Appl. Phys. Lett. 76 2000 1173 1175 [24] P. Adler S. Ghosh Solid State Sci. 5 2003 445 450

Dynamic Jahn–Teller distortion and oxygen vacancies in (La 1−x Pr x ) 1/3 Sr 2/3 FeO 3−δ investigated by mechanical spectroscopy

Anisotropic and Nonlinear Thermal and Chemical Expansion of La1–xSrxFeO3−δ (x = 0.3, 0.4, 0.5) Perovskite Materials

Charge Ordering Transition in (la, Pr) 1/3 Sr 2/3 FeO 3− Δ with Different Oxygen Concentration Investigated by Mechanical Spectroscopy

Anisotropic Chemical Expansion Of La1-Xsrxcoo3-Delta

Oxygen Vacancies and Their Effects on Tilting Transition in Perovskite (la1−xprx)1/3sr2/3feo3−δ Investigated by Mechanical Spectroscopy

Phase Transitions in La0.5Sr0.5FeO3−δ Investigated by Mechanical Spectrum

Charge order suppression in oxygen nonstoichiometric La 1/3Sr2/3FeO3-δ

Lattice effect on charge and magnetic ordering in La1/3 Sr2/3 FeO3−δ investigated by mechanical spectroscopy

Ultrasonic signature of Jahn–Teller effect in La1/3Sr2/3Co1−xFexO3 perovskites

Variation of ultrasonic behaviors in R<sub>1/3</sub>Sr<sub>2/3</sub>FeO<sub>3</sub>(R=La, Pr, Gd)

Complex Charge Ordering Phenomena in La1−xSrxFeO3−δ Investigated by Mechanical Spectroscopy

Charge Ordering Correlated Ultrasonic Anomalies in La1/3Sr2/3Fe1−xCrxO3 Perovskites

Lattice effect on charge and magnetic ordering in La <sub>1/3</sub> Sr <sub>2/3</sub> FeO <sub> 3− <i>δ</i> </sub> investigated by mechanical spectroscopy

Investigation on the low-frequency mechanical properties of La0.6Sr0.4Co1−xFexO3−δ materials

The Mn-doping effect on the charge ordering state of La1/3Sr2/3FeO3

Phase Transformations of Perovskite La0.64(Ba1−x Ca X )0.36feo3−δ Investigated by Mechanical Spectroscopy

Ultrasonic Anomalies in La1/3Sr2/3Fe1−xCoxO3 Perovskites

A-Site Ordering and Its Effect on Tilting Transition in Perovskite La0.75sr0.25feo3-Delta Investigated by Mechanical Spectroscopy

Ultrasonic study of La1/3Sr2/3Mn1-xFexO3 (x=0, 0.05)

Charge Disproportionation in La1-xCaxFeO3−δ (x = 0.4 and 0.5) Investigated by Mechanical Spectroscopy

Ultrasonic study on charge ordering in La1/3Sr2/3Fe0.95 Cr0.05O3