Abstract:Three novel NFAs named BTP‐2O, BTP‐O‐S, and BTP‐2S with chalcogen containing branched chains are developed for efficient organic solar cells. The champion power conversion efficiency (PCE) reaches 17.3% for PM6:BTP‐O‐S‐based devices. Additionally, the o‐xylene processed PM6:BTP‐O‐S‐based devices also exhibit a PCE of 17.10%. This work demonstrates that the chalcogen containing branched chain engineering provides effective access to high‐performance OSCs by well‐balanced between VOC and JSC, alleviating voltage loss, and enhancing the FF. The elaborate balance between the open‐circuit voltage (VOC) and the short‐circuit current density (JSC) is critical to ensure efficient organic solar cells (OSCs). Herein, the chalcogen containing branched chain engineering is employed to address this dilemma. Three novel nonfullerene acceptors (NFAs), named BTP‐2O, BTP‐O‐S, and BTP‐2S, featuring different peripheral chalcogen containing branched chains are synthesized. Compared with symmetric BTP‐2O and BTP‐2S grafting two alkoxy or alkylthio branched chains, the asymmetric BTP‐O‐S grafting one alkoxy and one alkylthio branched chains shows mediate absorption range, applicable miscibility, and favorable crystallinity. Benefiting from the enhanced π–π stacking and charge transport, an optimal power conversion efficiency (PCE) of 17.3% is obtained for the PM6:BTP‐O‐S‐based devices, with a good balance between VOC (0.912 V) and JSC (24.5 mA cm−2), and a high fill factor (FF) of 0.775, which is much higher than those of BTP‐2O (16.1%) and BTP‐2S‐based (16.4%) devices. Such a result represents one of the highest efficiencies among the binary OSCs with VOC surpassing 0.9 V. Moreover, the BTP‐O‐S‐based devices fabricated by using green solvent yield a satisfactory PCE of 17.1%. This work highlights the synergistic effect of alkoxy and alkylthio branched chains for high‐performance OSCs by alleviating voltage loss and enhancing FF.

Enhancement in Open Circuit Voltage Through A Cascade-Type Energy Band Structure

Single-layered organic photovoltaics with double cascading charge transport pathways: 18% efficiencies

Open Circuit Voltage Enhancement Due To Reduced Dark Current In Small Molecule Photovoltaic Cells

Higher open circuit voltage caused by chlorinated polymers endows improved efficiency of binary organic solar cell

Improvement of the efficiency of CuPc/C60-based photovoltaic cells using a multistepped structure

Enabling low voltage losses and high photocurrent in fullerene-free organic photovoltaics

Single‐Junction Organic Photovoltaic Cell with 19% Efficiency

Quaternary Blends with Double Cascading Charge Transport Pathways Reaching 17.40% Efficiency in Single-Layered Organic Photovoltaics

Simultaneous Improvement of Efficiency and Stability of Organic Photovoltaic Cells by using a Cross‐Linkable Fullerene Derivative

Enhanced open-circuit voltage of two side chain conjugated polythiophene derivatives blended with indene-C60 bisadduct

Nonfullerene Tandem Organic Solar Cells with High Open‐Circuit Voltage of 1.97 V

Optimizing Molecular Crystallinity and Suppressing Electron‐Phonon Coupling in Completely Non‐fused Ring Electron Acceptors for Organic Solar Cells

Enhanced efficiency of organic solar cells through trans-cinnamic acid doped cathode interface layer

Desired open-circuit voltage increase enables efficiencies approaching 19% in symmetric-asymmetric molecule ternary organic photovoltaics

High Open-Circuit Voltage Organic Solar Cells with 19.2% Efficiency Enabled by Synergistic Side-Chain Engineering

Achieving over 11% Power Conversion Efficiency in PffBT4T-2OD-based Ternary Polymer Solar Cells with Enhanced Open-Circuit-voltage and Suppressed Charge Recombination

High‐Efficiency Organic Solar Cells Enabled by Chalcogen Containing Branched Chain Engineering: Balancing Short‐Circuit Current and Open‐Circuit Voltage, Enhancing Fill Factor

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

Boosting Organic Photovoltaic Performance over 11% Efficiency with Photoconductive Fullerene Interfacial Modifier

Enhancement of All-Polymer Solar Cells by Addition of a Chlorinated Polymer and Formation of an Energy Cascade in a Nonhalogenated Solvent

Simultaneously Decreasing the Bandgap and V oc Loss in Efficient Ternary Organic Solar Cells