Abstract:This study reports the investigation of the morphology of the surface damaged during the laser scribing of glass and the analysis of the corresponding interaction mechanism between the laser and glass. In this study, the soda lime glass of 1.1 mm thick is scribed by an ultraviolet (UV) picosecond laser (Nd:YVO4) by varying laser power, scan speed and number of scans. From the analysis of experimental results, it is found that the surface morphology can be classified as three groups such as swelled surface, wave pattern (either shallow or deep) and groove depending on the accumulated laser energy per unit beam spot. The accumulation of the large laser energy (12–30 × 10−4 J) into the material induces volume meting and local vaporization below the surface without material removal, which makes bubbles inside glass volume and swelled surface through volume expansion. With the decrease of the energy accumulation (4.2–9 × 10−4 J), the surface morphology is changed into shallow wave pattern by slight material removal. With further decrease of the laser energy accumulation (1.4–3 × 10−4 J), either deep wave or groove morphology is obtained due to the increase of the material removal. Under very low laser energy accumulation region (0.3–1.05 × 10−4 J), the groove shape is only formed. In particular, the groove morphology without cracking is successfully produced within the range of 0.3–0.5 × 10−4 J. The threshold laser energy accumulation for surface damage is found to be around 0.25–0.3 × 10−4 J. Below this energy accumulation, modification in the surface morphology doesn’t occur. It is also found that the groove morphology is hard to obtain by even multiple laser scans if it is not well formed by single laser scan. The cracks produced during the scribing process can be characterized with several propagation morphologies. At the region of the relatively low laser energy accumulation, cracks propagating across the scan direction are only generated. However, cracks propagating both across and along the scan direction are found with the increase of the laser energy accumulation. Huge cracks (arc or sinusoidal curve shape) of several millimeters in size are produced under the very large laser energy accumulation.

Mechanism of Bump Formation on Glass Substrates During Laser Texturing

Investigations in the fabrication of surface patterns for wettability modification on a Zr-based bulk metallic glass by nanosecond laser surface texturing

Thermomechanical Coupling in Glassy Polymers: an Effective Temperature Theory

Surface Modification of Roll by Pulsed ND:YAG Laser: Bump Formation Caused by Martensitic Transformation

Research on the influence of laser molten pool flow and evaporation on the bump texture forming of aluminum plate surface

Generalized Model for Laser-Induced Surface Structure in Metallic Glass

Laser micro-texture formation mechanism based on modified heat-mass transfers and hydrodynamic models

Effect of microstructure on thermal field distribution of absorption glass with nanosecond laser-irradiated

Shape- and Size-Controllable Microstructure on Glass Surface Induced by Femtosecond Laser Irradiation.

Morphologies and nonlinear scaling of laser damage on glass surfaces by tightly focused femtosecond pulses

Investigation of the surface morphology in glass scribing with a UV picosecond laser

Targeted Microforming of Borosilicate Glass Induced by a Laser‐Ablation‐Free Process Using Femtosecond Pulses

Mechanisms of damage formation in glass in the process of femtosecond laser drilling

Initial Morphology and Feedback Effects on Laser-Induced Periodic Nanostructuring of Thin-Film Metallic Glasses

Bubble Generation in Germanate Glass Induced by Femtosecond Laser

Characterization of Morphology and Mechanical Properties of Glass Interior Irradiated by Femtosecond Laser

Prediction and Analysis of Borosilicate Glass Surface Deformation Induced by Flame Jet

Damage morphology and mechanism in ablation cutting of thin glass sheets with picosecond pulsed lasers

Laser-induced stress by multi-beam femtosecond pulses in fused silica

Mechanically inspired laser scribing of thin flexible glass

Volumetric glass modification with Gaussian and doughnut-shaped pulses: From localized laser energy absorption to absorption delocalization