Abstract:A series of polyethylene (PE) blends consisting of a linear high density polyethylene (HDPE) and a linear low density polyethylene (LLDPE) with an octane-chain branch density of 120/1000 carbon was prepared at different concentrations. The two components of this set of blends possessed isorefractive indices, thus, making it difficult to detect their liquid–liquid phase separation via scattering techniques. Above the experimentally observed melting temperature of HDPE, Tm = 133 °C, this series of blends can be considered to be in the liquid state. The LLDPE crystallization temperature was below 50 °C; therefore, above 80 °C and below the melting temperature of HDPE, a series of crystalline–amorphous PE blends could be created. A specifically designed two-step isothermal experimental procedure was utilized to monitor the liquid–liquid phase separation of this set of blends. The first step was to quench the system from temperatures of known miscibility and isothermally anneal them at a temperature higher than the equilibrium melting temperature of the HDPE for the purpose of allowing the phase morphology to develop from liquid–liquid phase separation. The second step was to quench the system to a temperature at which the HDPE could rapidly crystallize. The time for developing 50% of the total crystallinity (t1/2) was used to monitor the crystallization kinetics. Because phase separation results in HDPE-rich domains where the crystallization rates are increased, this technique provided an experimental measure to identify the binodal curve of the liquid–liquid phase separation for the system indicated by faster t1/2. The annealing temperature in the first step that exhibits an onset of the decrease in t1/2 is the temperature of the binodal point for that blend composition. In addition, the HDPE-rich domains crystallized to form spherulites which decorate the phase-separated morphology. Therefore, the crystal dispersion indicates whether the phase separation followed a nucleation-and-growth process or a spinodal decomposition process. These crystal-decorated morphologies enabled the spinodal curve to be experimentally determined for the first time in this set of blends.

Melt Miscibility of HDPE/UHMWPE, LDPE/UHMWPE, and LLDPE/UHMWPE Blends Detected by Dynamic Rheometer

Rheological, Thermal, and Morphological Properties of Low-Density Polyethylene/Ultra-High-Molecular-Weight Polyethylene and Linear Low-Density Polyethylene/Ultra-High-Molecular-Weight Polyethylene Blends

Dynamic Rheological Behavior of Hdpe/Uhmwpe Blends

Dissipative Particle Dynamics Study on the Phase Morphologies of the Ultrahigh Molecular Weight Polyethylene/polypropylene/poly(ethylene Glycol) Blends

Anomalous Melt Rheological Properties of Unimodal-MWD HDPE Blends

Effect of composition distribution on miscibility and co-crystallization phenomena in the blends of low density polyethylene with conventional and metallocene-based ethylene–butene copolymers

Rheological Behavior and Mechanical Properties of High‐density Polyethylene Blends with Different Molecular Weights

Investigation on Phase Separation Kinetics of Polyolefin Blends Through Combination of Viscoelasticity and Morphology.

Dissipative Particle Dynamics and Flory−Huggins Theories for Predicting the Rheological Behavior of Ultrahigh Molecular Weight Polyethylene Blends

Study on Rheological Properties and Relaxational Behavior of Poly(dianilinephosphazene)/low-Density Polyethylene Blends

Thermal and Rheological Properties of Polyethylene Blends with Bimodal Molecular Weight Distribution

Probing Liquid‐Liquid Phase Separation of a Polyethylene Blend with Thermal Analysis

Liquid–liquid Phase Separation in a Polyethylene Blend Monitored by Crystallization Kinetics and Crystal-Decorated Phase Morphologies

Rheologically Determined Phase Diagram And Dynamically Investigated Phase Separation Kinetics Of Polyolefin Blends

PHASE SEPARATION IN BIMODAL MOLECULAR WEIGHT HIGH DENSITY POLYETHYLENE WITH DIFFERING BRANCH CONTENTS BY MOLECULAR DYNAMICS AND MESODYN SIMULATION

Ultrasonic characterization of phase morphology of high density polyethylene/polyamide 6 blend melts

Miscibility of HDPE/EPO Blends

Computer simulation studies of the miscibility of poly(3-hydroxybutyrate)-based blends

Thermal, Rheological, Morphological and Mechanical Properties of High Density Polyethylene/ethylene Vinyl Acetate Copolymer (HDPE/EVA) Blends

Study on miscibility of poly(vinyl chloride) and polyepichlorohydrin by viscometric and thermal analysis

Improving the integration of HDPE/UHMWPE blends by high temperature melting and subsequent shear