Abstract:A novel and simple electroless Ni–Cu–P plating process was used for preparing corrosion-resistant and electromagnetic interference shielding wood-based composite. The effects of CuSO4·5H2O concentration, pH value in the plating solution and operation temperature on the metal deposition, surface resistivity, chemical composition, corrosion resistance and surface morphology of the composite were investigated. The surface morphologies were observed by using scanning electron microscopy and the chemical compositions were analyzed by X-ray energy dispersive spectrometer. The electromagnetic shielding effectiveness (ESE) was measured by spectrum analyzer. The corrosion resistance was evaluated by potentiodynamic corrosion measurement. The results show that metal deposition increases with pH value and temperature increase; however, it decreases with CuSO4·5H2O concentration increase. The corrosion resistance of the plated Ni–Cu–P coatings obviously depends on the total content of Cu and P in the coating. Higher total content of Cu and P leads to higher corrosion resistance. The optimum conditions are as follows: CuSO4·5H2O concentration of 1.0 g/L, pH value of 9.5, and operation temperature of 90 °C. The obtained coating contains 77.41 % Ni, 8.96 % Cu, and 13.63 % P. The wood-based composite exhibits higher corrosion resistance and ESE of around 60 dB in frequencies ranging from 9 kHz to 1.5 GHz. In this paper, a promising process for corrosion-resistant and electromagnetic shielding wood-based composites was developed.

Effect of CuSO4 Content in the Plating Bath on the Properties of Composites from Electroless Plating of Ni-Cu-P on Birch Veneer

Preparation of EMI Shielding and Corrosion-Resistant Composite Based on Electroless Ni-Cu-P Coated Wood

Electromagnetic Shielding Wood-Based Composite from Electroless Plating Corrosion-Resistant Ni–Cu–P Coatings on Fraxinus Mandshurica Veneer

Electromagnetic Interference Shielding Material from Electroless Copper Plating on Birch Veneer

Effect of Temperature on Electrlo se s Deposition of Ni-Cu-P Ternary Alloy on Birch Veneer

Study on Preparation of Electromagnetic Shielding Composite by Electroless Copper Plating on Fraxinus Mandshurica Veneer

Study on Electromagnetic Shielding Wood Ni -P Composite Prepared by Electroless Nickel Plating

Preparation and Characterization of Conductive and Corrosion-Resistant Wood-Based Composite by Electroless Ni–W–P Plating on Birch Veneer

Preparation of Wood-Based Emi Shielding Composite Via A Short Process Electroless Plating

Fabrication of Magnetic and EMI Shielding Wood-Based Composite by Electroless Ni-Fe-P Plating Process

Electroless Copper Plating on Fraxinus Mandshurica Veneer Using Glyoxylic Acid As Reducing Agent

Electromagnetic-shielding, Wood-based Material Created Using a Novel Electroless Copper Plating Process

Preparation of Wood-based Electromagnetic Shielding Composite by Electroless Nickel Plating on Birch Veneer Pretreated with NaBH_4

Electromagnetic Shielding and Corrosion Resistance of Electroless Ni-P and Ni-P-Cu Coatings on Polymer/Carbon Fiber Composites

Preparation of Corrosion-Resistant, EMI Shielding and Magnetic Veneer-Based Composite Via Ni–Fe–P Alloy Deposition

Effect of Cu Content in Electroless Ni-Cu-P Coatings on Their Microstructure and Properties

Electroless copper plating of Fraxinus mandshurica veneer using glyoxylic acid as reducing agent

ELECTROLESS NICKEL PLATING ON CHITOSAN-MODIFIED WOOD VENEER

Fabrication of a hydrophobic, electromagnetic interference shielding and corrosion-resistant wood composite via deposition with Ni–Mo–P alloy coating

Preparation of Electromagnetic Shielding Wood-Metal Composite by Electroless Nickel Plating

Effect of Copper Content on the Properties of Ni–Cu–P Plated Polyester Fabric