Abstract:When the local heat flux exceeds specified flux limit, tungsten PFC surfaces can be damaged, which is not acceptable for a reliable reactor operations. The divertor PFCs are typically designed for a specific heat flux limit usually assuming an average steady-state heat flux which is typically 5–10 MW/m 2 . However, in addition to steady-state heat flux, fusion reactor divertor PFCs could experience transient heat fluxes such as ELMs and/or other magnetic reconnection events which can deposit large transient heat fluxes onto the divertor PFCs. The transient divertor heat flux could be significantly larger than the steady-state heat flux which could damage the solid PFC surfaces. The divertor heat flux can be subjected to additional complications such as the uncertainties in the the divertor strike point heat flux projection. Moreover, there are additional experimental observations of non-axisymmetric power flux which can occur under non-axisymmetric magnetic perturbations. The liquid lithium (LL) PFCs is more resilient against such transient heat fluxes as they could evaporate LL as needed and the lost LL can be then replenished afterward. In this paper, we analyze a case for a transient divertor heat pulse of 1 MJ in 10 ms for a ITER-size reactor. This is a small perturbation (~ 0.1%) to the expected plasma stored energy compared to the previously analyzed case of 20 MJ heat pulse. Even with this relatively modest heat pulse, the LL surface undergoes ~ 100 °C temperature rise. However, the resulting LL surface heating without rapid cooldown mechanism could lead to excessive LL evaporation continuing well after the transient heat flux resulting in a significant Li injection of ~ 0.6 mol in about a 200 ms period. This amount of Li injection could cause plasma dilution and performance degradation. On the other hand, an active Li injection capability if optimized could prevent the LL surface temperature rise and thus reducing subsequent Li evaporation into the plasma by a factor of 7 compared to the passive LL PFC case. A crucial tool of active Li injection is a rapid response pellet injector which could inject light impurity pellets before the excessive heat flux could reach the divertor plate causing serious damage. A simple pellet ablation model suggests a favorable pellet deposition profile for smaller ~ 0.1 mm radius pellet with ~ 10–20 m/s velocity. Moreover, if it is possible to inject from the private flux region, the pellet injection efficiency into the high heat flux strike point region can be as high as 80% compared to ~ 50% for the injection from outer radius region. The pellet deposition efficiency can be further improved by designing a shell-pellet which can burst when a certain ablation fraction is reached. A possible implementation technique using an inductive pellet injector with a rapid time response of a few msec is proposed here which can be tested in NSTX-U.

Investigations on Interactions Between the Flowing Liquid Lithium Limiter and Plasmas

Divertor Power Deposition Control and ELM Mitigation with Supersonic Molecular Beam Injection in the EAST Tokamak

Overview of Experimental Results on the HL-2A Tokamak

Overview of Hl-2a Experiment Results

OV / 4-5 1 Overview of Experimental Results on the HL-2 A Tokamak

Present Progress of Plasma Transport Study on HL-2A

OV / 4-3 1 Overview of Experimental Results on HL-2 A

Overview of the Recent Study on ELM Mitigation Physics with Different External Actuators on HL-2A Tokamak

Experiment of a Pump Limiter in the HL-1 Tokamak

Analysis of Lithium Driven Electron Density Peaking in FTU Liquid Lithium Limiter Experiments

Power Balance Investigation in Long-Pulse High-Performance Discharges with ITER-like Tungsten Divertor on EAST

Deuterium retention in co-deposition with lithium in Magnum-PSI: experimental analysis and comparison with SOLPS-ITER

I-mode plasma confinement improvement by real-time lithium injection and its classification on EAST Tokamak

Influence of hydrogen content in tokamak scrape-off-layer on performance of lithium divertor

Density Limits Investigation and High Density Operation in EAST Tokamak

A comparative study of the effects of liquid lithium and tin as DEMO divertor targets on the heat loads and SOL properties

Active Lithium Injection for a Real Time Control of the Divertor Heat Flux for Fusion Devices

Predictive modeling of a lithium vapor box divertor in NSTX-U using SOLPS-ITER

The design of 3D-printing liquid lithium divertor target plate and its interaction with high-density plasma

Enhancement of Tokamak Fusion Test Reactor Performance by Lithium Conditioning