Abstract:Lithium-sulphur (Li-S) battery, with the high theoretical capacity density (~1675 mAh g-1) and energy density (~2600 Wh kg-1) as well as the easy access and non-toxic of raw materials, demonstrates a promising prospect among the high energy storage systems for electric vehicles (EVs) and portable electronic devices. However, several issues must be handled before its commercial application. Differing from traditional lithium-ion batteries, intermediate polysulfides generate and dissolve in the organic electrolyte during the discharge process of lithium-sulfur batteries. The dissolved polysulfides, shuttling between the cathode and anode, lower the utilization of sulfur. However, the dissolution of polysulfide in a lithium-sulfur battery is highly dependent on the sulfur/electrolyte loading. Thus an appropriate dosage of electrolyte will build a concentration gradient, which will limit the dissolution of polysfulfides. Herein, a lithium-sulfur cell with a high initial discharge capacity of 1053 mAh g-1 at a high rate of 1 C and an ultralow decay rate of 0.049 %/per cycle during 1000 cycles was obtained by using CNT-sulfur cathode and suppressing polysulfide shuttle to a shuttle factor of 0.02 by matching the sulfur/electrolyte loading[1]. Beyond the issue of polysulfide shuttle, Li-S battery is always with low practical energy density because sulfur has a low electrical conductivity (5×10-30 S cm-1 at 25 oC) and extra conductive network is highly required. Generally, the addition of conductive materials will neutralize the advantage in high energy density of Li-S battery. Herein, we employed CNTs to build the unblocked conductive skeleton and room-temperature, one-step ball-milling treatment of aligned CNTs and sulfur was applied to obtain high sulfur content of 90%. The 90% sulfur loading cathode exhibited a superior density of 1.98 g cm-3 (2.07 g cm-3 for sulfur), which greatly increases the volumetric energy density of lithium-sulfur battery[2]. To improve the areal density of sulfur in the cathode further, a 3D Al foam was employed as the long-range conductive matrix. The combination of 3D Al foam with CNT frameworks not only exhibits long-/short-range scaffolds as electron pathways through hierarchical point-line-plate contact, but also offers vast void space to accommodate huge amount of active materials and interconnected channels with short diffusion pathways and low resistance. A high sulfur loading of 7.0 mg cm-2 (based on the surface area of the electrode) was available with a discharge capacity of 6.02 mAh cm-2 (860 mAh g-1) at a current density of 1.17 mA cm-2 (167 mA g-1). Based on the total weight of the cell, a super high energy density of 367 Wh kg-1 was achieved, which is much higher than the cell with routine Al foil current collectors[3]. Reference [1]Cheng X-B, Huang J-Q, Peng H-J et al., Journal of Power Sources. 2014, 253: 263-268. [2]Cheng X-B, Huang J-Q, Zhang Q et al., Nano Energy, 2014, 4: 65–72. [3]Cheng X-B, Peng H-J, Huang J-Q et al., Journal of Power Sources. 2014, 261: 264-270.

Nitrogen, Sulfur-Codoped Graphene Sponge As Electroactive Carbon Interlayer for High-Energy and -Power Lithium–sulfur Batteries

Optimized Sulfur-Loading in Nitrogen-Doped Porous Carbon for High-Capacity Cathode of Lithium–sulfur Batteries

Efficient Polysulfide Barrier of a Graphene Aerogel–carbon Nanofibers–ni Network for High-Energy-density Lithium–sulfur Batteries with Ultrahigh Sulfur Content

Encapsulating Sulfur into a Gel-Derived Nitrogen-Doped Mesoporous and Microporous Carbon Sponge for High-Performance Lithium-Sulfur Batteries

Dual‐Confined Flexible Sulfur Cathodes Encapsulated in Nitrogen‐Doped Double‐Shelled Hollow Carbon Spheres and Wrapped with Graphene for Li–S Batteries

3D Dual-Confined Sulfur Encapsulated in Porous Carbon Nanosheets and Wrapped with Graphene Aerogels As A Cathode for Advanced Lithium Sulfur Batteries

Nitrogen Doped Carbon Nanosheets Encapsulated in Situ Generated Sulfur Enable High Capacity and Superior Rate Cathode for Li-S Batteries

Hierarchical Nanostructured Carbon/Sulfur Hybrid Cathode for High-Performance Lithium-Sulfur Battery

Stabilizing Sulfur Cathodes Using Nitrogen-Doped Graphene As a Chemical Immobilizer for Li S Batteries

Carbon-nanotube/sulfur Cathode with In-Situ Assembled Si3N4/graphene Interlayer for High-Rate and Long Cycling-Life Lithium-Sulfur Batteries

Self-assembled N-graphene nanohollows enabling ultrahigh energy density cathode for Li-S batteries

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

Nitrogen-doped microporous carbon with narrow pore size distribution as sulfur host to encapsulate small sulfur molecules for highly stable lithium-sulfur batteries

Liquid-phase Exfoliated-Graphene-supporting Nanostructural Sulfur As High-Performance Lithium–sulfur Batteries Cathode

Horizontally Aligned Lamellar Porous Graphene/nickel Composite for High Volumetric Capacity Lithium-Sulfur Batteries

Carbon/Sulfur Aerogel with Adequate Mesoporous Channels as Robust Polysulfide Confinement Matrix for Highly Stable Lithium–Sulfur Battery

Long-life Li/polysulphide batteries with high sulphur loading enabled by lightweight three-dimensional nitrogen/sulphur-codoped graphene sponge

Ultraﬁne Nanosulfur Particles Sandwiched in Little Oxygen-functionalized Graphene Layers as Cathodes for High Rate and Long-life Lithium-Sulfur Batteries.

Strong Lithium Polysulfide Chemisorption on Electroactive Sites of Nitrogen-Doped Carbon Enables High-Performance Lithium-Sulfur Battery Cathodes

High Sulfur Loading Composite Wrapped By 3d Nitrogen-Doped Graphene As A Cathode Material For Lithium-Sulfur Batteries

Encapsulating Sulfur into Carbon Nanotube Framework for Robust Lithium-Sulfur Batteries