Abstract:Abstract A water extraction device that takes water from air in dry area is proposed. This device is designed to meet domestic water demand in remote rural areas, where the climate is dry and fresh water is scarce. The device can be driven effectively by low-temperature waste heat and has the characteristics of large daily water production, low energy consumption per unit of water and high water quality. Because the moisture content of air in dry area is very low, the effect of direct condensation is limited. Solid adsorbent is able to adsorb water vapor from air at a low temperature and release water vapor at under high temperature, which can be used for water extracting from air. To improve its performance under dry circumstances, the key technical point of this device is to use solid adsorbent to collect water vapor from other air to raise its dew point temperature, and then use high temperature cold source to condense water vapor from it. In this paper, configurations of the solid adsorption are proposed, which can be driven with low regeneration temperature under the same humidity increasing amount. This device uses multi-stage desiccant wheels to realize humid increasing. Desiccant wheel can be driven with high temperature to take water vapor from dehumidification air and release water vapor to regeneration air. The multi-stage configuration is good for the reduction of regeneration temperature, making applications of low temperature waste heat form heat pumps possible. Then, influencing factors of water extracting rate are analyzed. The influencing of regeneration temperature, humid reduction amount of the humidified air and cooling and heating systems, etc., are analyzed. Last, air handling processes considering cold and heat sources are recommended to reduce energy consumption. The heat pump driven scenarios are discussed in particular. Through optimization, the water extracting rate can be increased and energy consumption per unit of water can be reduced. At present, this paper only studies air water extracting processes and thermal processes, and does not involve structure of the device, water purification and power consumption of fans, etc.

Lowering the regeneration temperature of a rotary wheel dehumidification system using exergy analysis

Analysis of a Hybrid System of Adiabatic Absorption two-stage Liquid Desiccant and CO2 Transcritical Cycles

Irreversible Processes and Performance Improvement of Desiccant Wheel Dehumidification and Cooling Systems Using Exergy

Exergy destruction comparison of facial area ratio on dehumidification performance of the rotary desiccant wheel system under conventional and deep dehumidification

Performance investigation and exergy analysis of air-handling processes using liquid desiccant and a desiccant wheel

Experimental Investigation and Effectiveness Analysis of a Desiccant Wheel Dehumidification System with Low Air Humidity

Influence of the Number of Stages on the Heat Source Temperature of Desiccant Wheel Dehumidification Systems Using Exergy Analysis

Performance Investigation and Exergy Analysis of Two-Stage Desiccant Wheel Systems

Experimental and numerical study on low temperature regeneration desiccant wheel: Parameter analysis with a comprehensive energy index

A Simulation Study of Heat and Mass Transfer in A Honeycombed Rotary Desiccant Dehumidifier

Performance evaluation of a rotary dehumidifier with molecular sieve desiccant using coupled regeneration mode: Experimental Investigation

Optimization of a rotary desiccant wheel for enthalpy recovery of air-conditioning in a humid hospitality environment

Enhancing Exergy Performance: Addressing Air Parameters Nonuniformity at the Outlet Cross-Section in Desiccant Wheel Air-Conditioning

Exergy analysis of dehumidification systems: A comparison between the condensing dehumidification and the desiccant wheel dehumidification

Exergy Analysis and Performance Improvement of Liquid-Desiccant Deep-Dehumidification System: an Engineering Case Study

Numerical investigation and comparison on energy performance and exergy destruction of cascading deep dehumidification systems with dehumidification amount exceeding 95%

Thermodynamic analysis of desiccant wheel coupled to high-temperature heat pump system

Experimental Investigation of Precooling Desiccant-Wheel Air-Conditioning System in a High-Temperature and High-Humidity Environment

Performance Optimization of a Heat Pump Driven Liquid Desiccant Dehumidification System Using Exergy Analysis

Heat and Mass Transfer Analysis and Performance Comparison for Different Solid Dehumidification Methods

Performance Evaluations of Extracting Water From Dry Air Using Multi-Stage Desiccant Wheels and Vapor Compression Cycle