Abstract:The 2195 Al-Cu-Li alloy is widely utilized in the aerospace industry due to its lightweight nature and high strength. Consequently, gaining a comprehensive understanding of techniques to enhance its microstructural and mechanical properties is crucial for the consistent production of reliable and high-strength aerospace components. In this investigation, a pristine 2195 industrial ingot was subject to three distinct forging pretreatments: PT1, which involved a direct three upsetting and three stretching (3U3S) process; PT2, which combined double stage homogenization (DH) with 3U3S; and PT3, which involved DH along with six upsetting and six stretching (6U6S). Subsequent warm deformation and T8 aging treatment were applied to the pretreated forgings. The microstructure evolution during the processes and the final mechanical properties in three orthogonal dimensions were examined. The findings revealed that the combination of DH and multi-dimensional forging (MDF) facilitated the dissolution of non-equilibrium phases to a greater extent. Consequently, the main strengthening phase transformed from the T 1 + δ` phase observed in PT1 to the denser T1 + little θ` phase observed in PT2 and PT3 after T8 aging treatment. Notably, the tensile strength and yield strength of PT2 and PT3 specimens increased by 20-30 MPa in all three directions. Moreover, the MDF process accelerated the recrystallization behavior from PT1 to PT3, resulting in a gradual reduction in the average grain size of the pretreated samples from 356 μm to 186 μm. Following warm forging and T8 aging, the grains exhibited a finer and equiaxed structure. Additionally, the coarse phase was identified as the primary source of transgranular cracking. The coarse phases within the matrix became more homogeneous and finer from PT1 to PT3, with a gradual decrease in their area fraction. On the fracture surfaces, the aggregation of coarse phases diminished. Consequently, the elongation in the z-direction improved, and the elongation anisotropy and standard deviation decreased in all three directions for PT3 specimens. The findings presented in this study provide valuable insights into the high-performance manufacturing of Al-Cu-Li alloys.

The effect of strain on dynamic recrystallization of PM Ti–45Al–10Nb intermetallics during isothermal forging

Unexpected Dynamic Recrystallization Behavior of Ti-7Cu Alloy in Semi-Solid State

Study of pre-precipitated 8 phase promoting deformation twinning and recrystallization behavior of Inconel 718 superalloy during hot compression

Microstructure simulation and experiment investigation of dynamic recrystallization for ultra high strength steel during hot forging

The Effect of the Forging Process on the Microstructure and Mechanical Properties of a New Low-Cost Ti-5Al-1.5Mo-1.8Fe Alloy

Microstructure evolution and dynamic softening behavior of as-forged Ti-43Al-9V-Y-0.2Y alloy under different deformation parameters

Effect of Multidirectional Isothermal Forging on Microstructure and Mechanical Properties in Ti-6Al-4V Alloy

Dynamic precipitation and its effect on microstructure of 2195 Al–Li alloy during medium/high temperature deformation

Dynamic recrystallization mechanism and improved mechanical properties of a near α high temperature titanium alloy processed by severe plastic deformation

Dynamic Recrystallization Behaviour of Nb-Ti Microalloyed Steels

Influence of Forging Temperature on the Microstructures and Mechanical Properties of a Multi-Directionally Forged Al–Cu–Li Alloy

Dynamic recrystallization mechanisms of as‐extruded GH4151 alloy during hot deformation

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Improvement on high-temperature tensile strength and ductility of selective electron beam melting TiAl alloys via small-strain forging

Dynamic recrystallization and hot processing map of Ti-48Al-2Cr-2Nb alloy during the hot deformation

Effect of Pass Strain on the Microstructure, Texture and Mechanical Properties of AZ31 Magnesium Alloy Fabricated by High Strain Rate Multiple Forging

Microstructural Variation and a Physical Mechanism Model for a Ti-55511 Alloy during Double-Stage Hot Deformation with Stepped Strain Rates in the β Region

Effects of Stress‐Aging Pretreatment on Hot Deformation Behavior and Microstructure Evolution of a Ni–Cr–Nb–Mo–Ti Alloy

Microstructure and deformation mechanism of dissimilar titanium alloy Ti600/Ti22Al25Nb weld joints strengthened by isothermal forging

Dynamic Recrystallization Behavior of Fe–20Cr–30Ni–0.6Nb–2Al–Mo Alloy

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation