Air-guiding photonic bandgap fiber with improved triangular air-silica photonic crystal cladding

M. Yan,P. Shum

DOI: https://doi.org/10.48550/arXiv.physics/0510225

2005-10-25

Optics

Abstract:We introduce a small-core air-guiding photonic crystal fiber whose cladding is made of improved air-silica photonic crystal with non-circular air holes placed in triangular lattice. The fiber achieves un-disturbed bandgap guidance over 350nm wavelength range.

What problem does this paper attempt to address?

Submicron and Nano-Diameter Silica Wires for Optical Wave Guiding

LM Tong,RR Gattass,JY Lou,JB Ashcom,MY Shen,E Mazur

DOI: https://doi.org/10.1117/12.481726

2002-01-01

Abstract:Based on the exact solutions of Maxwell's equations, we have studied the basic theoretical properties of submicron and nano-diameter air-cladding silica-wire waveguides. The single-mode condition and the modal field of the fundamental modes have been obtained. Silica wires with diameters of 100-1000nm and lengths ranging from hundreds of micrometer to over 1 millimeter have been fabricated. SEM examination shows that these wires have uniform diameters and smooth surfaces, which are favorable for optical wave guiding. Light has been sent into these wires by optical coupling, and guiding light through a bent wire has also been demonstrated. These wires are promising for assembling photonic devices on a micron or submicron scale.
Silica Nanofibers and Subwavelength-Diameter Fibers

Limin Tong,Eric Mazur

DOI: https://doi.org/10.1016/b978-012369406-5/50013-8

2007-01-01

Abstract:Air-clad silica nanofibers, named for their submicrometer diameters, have a large core–cladding index contrast for efficient optical confinement. For single-mode operation, these fibers are usually thinner than the wavelength of the light they carry and are therefore also called sub wavelength-diameter fibers. The small diameter of a nanofiber and the large core–cladding index contrast yield a number of interesting optical properties such as tight optical confinement, large evanescent fields, strong field enhancement, and large waveguide dispersions. A few techniques can be used to fabricate silica nanowires or nanofibers such as photo or electron beam lithography, chemical growth, and taper drawing of optical fibers. The taper-drawing method exhibits simplicity in fabrication and also the ability to fabricate nanofibers with extraordinary diameter uniformities, atomic-level surface smoothness, and long length that are difficult to achieve by any other means. The nanofibers obtained with the two-step taper-drawing techniques consist of three parts—a millimeters-long taper that is connected to the starting microfiber, a uniform nanofiber with a length up to tens of millimeters, and an abruptly tapered end that is usually several to tens of micrometers in length.
Mid-infrared dual-cladding photonic crystal fiber with high birefringence and high nonlinearity

Zhiwei Shen,Keyao Li,Chunhua Jia,Hongzhi Jia

DOI: https://doi.org/10.1007/s10043-020-00596-7

IF: 1.2

2020-05-08

Optical Review

Abstract:We propose two mid-infrared photonic crystal fibers with an elliptical As2S3 core and a dual-cladding structure with high birefringence and high nonlinearity. The cladding filling material is silica and the core material is As2S3. The full vector finite-element method is used to study the birefringence, and nonlinear coefficient of the structure in the 3–5 μm band. The Simulation results show that the birefringence of the two structures can reach a maximum of 0.2169, and the nonlinear coefficient can reach a maximum of 3763.42 W−1/km. From these characteristics, it is concluded that the proposed structure will be ideal for mid-infrared fiber sensing, precision optics and nonlinear optics.

optics
Band structure of photonic crystal fibers with silica rings in triangular lattice

Qin-Ling Zhou,Xing-Qiang Lu,Dan-Ping Chen,Cong-Shan Zhu,Jian-Rong Qiu

DOI: https://doi.org/10.1016/j.optcom.2006.06.026

IF: 2.4

2006-01-01

Optics Communications

Abstract:The characteristics of the cladding band structure of air-core photonic crystal fibers with silica rings in triangular lattice are investigated by using a standard plane wave method. The numerical results show that light can be localized in the air core by the photonic band gaps of the fiber. By increasing the air-filling fraction, the band gap edges of the low frequency photonic band gaps shift to shorter wavelength, whereas the band gap width decreases linearly. In order to make a specified light fall in the low frequency band gaps of the fiber, the interplay of the silica ring spacing and the air-filling fraction is also analyzed. It shows that the silica ring spacing increases monotonously when the air-filling fraction is increased, and the spacing range increases exponentially. This type fiber might have potential in infrared light transmission.
Rectangular Porous-Core Photonic-Crystal Fiber With Ultra-Low Flattened Dispersion and High Birefringence for Terahertz Transmission

Yani Zhang,Xin Jing,Dun Qiao,Lu Xue

DOI: https://doi.org/10.3389/fphy.2020.00370

IF: 3.718

2020-10-08

Frontiers in Physics

Abstract:We propose a novel porous-core photonic crystal fiber (PCF) consisting of asymmetrical rectangular air holes in the core and six-ring hexagonal lattice circular air holes in the cladding for achieving low-loss polarization terahertz transmission in a wide frequency range. By assuming TOPAS as the host material, the finite element method (FEM) is used to investigate its properties. The near-zero flattened dispersion of −0.01±0.02 ps/THz/cm is achieved over a frequency range of 1.0–2.0 THz, as well as a high birefringence of 7.1 × 10<sup>−2</sup> which can be useful for polarization-maintaining applications. Also, critical parameters such as mode field distribution, effective material loss, confinement loss, and effective mode area are discussed in detail. Further, fabrication possibilities are discussed briefly by comparing recent work on similar waveguide structures.<strong>OCIS Codes:</strong> 040.2235 (Far infrared or terahertz), 060.4005 (Micro-structured fibers), 060.2420 (Fibers, polarization-maintaining), 160.5470 (Polymers).

physics, multidisciplinary
Simultaneously Achieving a Large Negative Dispersion and a High Birefringence Over Er and Tm Dual Gain Bands in a Square Lattice Photonic Crystal Fiber

Yong Soo Lee,Chung Ghiu Lee,Faouzi Bahloul,Soeun Kim,Kyunghwan Oh

DOI: https://doi.org/10.1109/jlt.2019.2891756

IF: 4.7

2019-02-15

Journal of Lightwave Technology

Abstract:We proposed a novel photonic crystal fiber composed of a double-cladding square lattice that could be used in dual-band, Er and Tm optical gain bands, simultaneously supporting a large negative dispersion and a high birefringence. We theoretically investigated the light guiding property through the proposed photonic crystal fiber by using a vectorial finite-element method with a perfectly matched layer. By optimizing the structural parameters, we obtained an ultra-large negative dispersion of 20,186 ps(nmkm) and a very high birefringence of 9.27 103 at the wavelength of 1.55 m in the Er gain band and a very large negative dispersion of 8,067 ps(nmkm) and a high birefringence of 1.0 103 at the wavelength of 1.87 m in the Tm band. We further discussed the roles of waveguide parameters on the chromatic dispersion, its slope, and the birefringence of the fiber as well as the mode field diameter. The proposed fiber could be directly applied for dual-band dispersion and polarization control in fiber laser cavities as well as optical communications and sensors in the dual bands.

engineering, electrical & electronic,optics,telecommunications
Bandgap guidance in hybrid chalcogenide-silica photonic crystal fibers

Nicolai Granzow,Patrick Uebel,Markus A Schmidt,Andrey S Tverjanovich,Lothar Wondraczek,Philip St J Russell

DOI: https://doi.org/10.1364/OL.36.002432

2011-07-01

Abstract:We report a hybrid chalcogenide-silica photonic crystal fiber made by pressure-assisted melt-filling of molten glass. Photonic bandgap guidance is obtained at a silica core placed centrally in a hexagonal array of continuous centimeters-long chalcogenide strands with diameters of 1.45 μm. In the passbands of the cladding, when the transmission through the silica core is very weak, the chalcogenide strands light up with distinct modal patterns corresponding to Mie resonances. In the spectral regions between these passbands, strong bandgap guidance is observed, where the silica core transmission loss is 60 dB/cm lower. The pressure-assisted fabrication approach opens up new ways of integrating sophisticated glass-based devices into optical fiber circuitry with potential applications in supercontinuum generation, magneto-optics, wavelength selective devices, and rare-earth-doped amplifiers with high gain per unit length.
Refractive-index guiding single crystal optical fiber with air–solid cladding

Jinmin Ding,Fanchao Meng,Xiaoting Zhao,Lvyun Yang,Xin Wang,Shuqin Lou,Xinzhi Sheng,Ryszard Buczyński,Guangming Tao,Sheng Liang

DOI: https://doi.org/10.1364/ome.427440

2021-08-17

Optical Materials Express

Abstract:Jinmin Ding, Fanchao Meng, Xiaoting Zhao, Lvyun Yang, Xin Wang, Shuqin Lou, Xinzhi Sheng, Ryszard Buczyński, Guangming Tao, Sheng LiangIn this study, a refractive-index guiding single-crystal fiber (SCF) with air–solid cladding was proposed and numerical simulation ... [Opt. Mater. Express 11, 2994-3006 (2021)]

materials science, multidisciplinary,optics
High Transmitting and Coupling Characteristics of Light at the Surface of A Photonic Crystal with A Triangular Lattice of Air Holes

Jun Zhang,Tianbao Yu,Nianhua Liu,Jianyi Yang,Qinghua Liao,Xiaoqing Jiang

DOI: https://doi.org/10.1364/josab.29.000748

2012-01-01

Abstract:We investigate and simulate the light transmitting and coupling characteristics of surface mode waveguides (SMWs) based on photonic crystals (PhCs) with a triangular lattice of air holes. We demonstrate that surface waves can be efficiently propagated and served as a new kind of high-efficiency single-SMW-based filter with broad bandwidth in the outer space of PhCs. We also explore the highly efficient coupling of hetero-SMWs constructed by cascading different truncated surfaces. The coupling efficiency is insensitive to the interface position. (C) 2012 Optical Society of America
A New Method of Modeling Cladding Band Structure of Air-Guiding Photonic Crystal Fibers

Qin-Ling Zhou,Xing-Qiang Lu,Dan-Ping Chen,Cong-Shan Zhu,Jian-Rong Qiu

DOI: https://doi.org/10.1016/j.jnoncrysol.2006.10.081

IF: 4.458

2008-01-01

Journal of Non-Crystalline Solids

Abstract:Cladding band structure of air-guiding photonic crystal fibers with high air-filling fraction is calculated in terms of fiber shape variation. The fundamental photonic band gap dependence on structure parameters, air-filling fraction and spacing, is also investigated. The numerical results show that the band gap edges shift toward longer wavelength as the air-filling fraction is increased, whereas the relative band gap width increases linearly. For a fixed air-filling fraction, the band gap edges with respect to spacing keep constant. With this method, the simulation results agree well with the reported data.
Ultra-low transmission loss (7.7 dB/km at 750 nm) inhibited-coupling guiding hollow-core photonic crystal fibers with a single ring of tubular lattice cladding

B. Debord,A. Amsanpally,M. Chafer,A. Baz,M. Maurel,J.M Blondy,E. Hugonnot,F. Scol,L. Vincetti,F. Gerome,F. Benabid

DOI: https://doi.org/10.48550/arXiv.1610.01513

2016-10-06

Abstract:The advent of photonic bandgap (PBG) guiding hollow- core photonic crystal fiber (HC-PCF) sparked the hope of guiding light with attenuation below the fundamental silica Rayleigh scattering limit (SRSL) of conventional step-index fibers. Unfortunately, the combination of the strong core-cladding optical-overlap, the surface roughness at the silica cladding struts and the presence of interface-modes limited the lowest reported transmission-loss to 1.2 dB/km at 1550 nm. This hope is recently revived by the introduction of hypocycloid core- contour (i.e. negative curvature) in inhibited-coupling (IC) guiding HC-PCF, and the reduction of their confinement loss to a level that makes them serious contenders for light transmission below the SRSL in UV- VIS-NIR spectral range. Here, we report on several IC guiding HC-PCFs with a hypocycloid core-contour and a cladding structure made of a single ring from a tubular lattice. The fibers guide in the UV-VIS and NIR, and among which we list one with a record transmission loss of 7.7 dB/km at ~750 nm (only a factor ~2 above the SRSL), and a second with an ultra-broad fundamental-band with loss in the range of 10-20 dB/km spanning from 600 to 1200 nm. Both fibers present near-single mode guidance and very low bend loss sensitivity. The results show that the limit in the transmission is set by confinement loss for wavelengths longer than ~1 {\mu}m and by surface- roughness for shorter wavelengths, thus indicating that transmission loss well below the SRSL in the visible is possible with a surface roughness reduction and would open the possibility of the first UV low-loss light- guidance.

Optics
Terahertz Circular Photonic Crystal Fiber

Liang Wang,Dongxiao Yang,Yin Chen,Zhineng Li

DOI: https://doi.org/10.1109/icimw.2006.368451

2006-01-01

Abstract:Terahertz (THz) circular photonic crystal fiber (CPCF) with the similar distribution of air holes as that in variable-size circular photonic crystal in polyethylene material was introduced. Guiding and dispersion properties of the CPCF with different parameters have been accurately computed. Results show that the CPCF is a useful terahertz waveguide which has good ability to confine THz fields, low group-velocity dispersion parameter and low relative dispersion slope. Furthermore, the polyethylene material that is transparent to terahertz wave is inexpensive and easy to operate.
Ultra-large Bandwidth Hollow-Core Guiding in All-Silica Bragg Fibers with Nano-Supports

G Vienne,Y Xu,C Jakobsen,HJ Deyerl,JB Jensen,T Sorensen,TP Hansen,YY Huang,M Terrel,RK Lee,NA Mortensen,J Broeng,H Simonsen,A Bjarklev,A Yariv

DOI: https://doi.org/10.1364/opex.12.003500

IF: 3.8

2004-01-01

Optics Express

Abstract:We demonstrate a new class of hollow-core Bragg fibers that are composed of concentric cylindrical silica rings separated by nanoscale support bridges. We theoretically predict and experimentally observe hollow-core confinement over an octave frequency range. The bandwidth of bandgap guiding in this new class of Bragg fibers exceeds that of other hollow-core fibers reported in the literature. With only three rings of silica cladding layers, these Bragg fibers achieve propagation loss of the order of 1 dB/m.
Quaternary One-Dimensional Photonic Crystal Cladding Hollow-Core Bragg Fiber

Lichao Shi,Wei Zhang,Jie Jin,Yidong Huang,Jiangde Peng

DOI: https://doi.org/10.1364/cleo_si.2011.cthm4

2011-01-01

Abstract:We proposed and fabricated hollow-core Bragg fiber with core Bragg fiber with quaternary one-dimensional photonic crystal cladding. The new cladding increases the design flexibility. The transmission measurements revealed that it guides light mainly by the higher order photonic bandgaps. (C) 2010 Optical Society of America
Polarization maintaining air-core bandgap terahertz fiber

Guobin Ren,Xia Yu,Yandong Gong,Juanjuan Hu,Ping Shum,Guanghui Wang

DOI: https://doi.org/10.1145/1509315.1509325

2008-01-01

Abstract:We proposed a novel polarization maintaining air-core bandgap polymer fiber for terahertz (THz) wave guiding. The periodic arrangement of square holes with round corners in cladding offers bandgap effect for mode guiding. The guiding properties including transmission bandwidth, numerical aperture, phase-index birefringence, modal absorption loss and bend loss are systematically investigated. Numerical simulations show that the bandgap effect repels the modal power from the absorbent background polymers, resulting in a significant suppression of absorption loss of polymers by a factor of more than 25. The phase-index birefringence of the proposed THz fiber is on the order of 10-3.
High Birefringence and Low Loss Circular Air-Holes Photonic Crystal Fiber Using Complex Unit Cells in Cladding

Tzong-Jer Yang,Lin-Fang Shen,Yuan-Fong Chau,Ming-Je Sung,Daru Chen,Din Ping Tsai

DOI: https://doi.org/10.1016/j.optcom.2008.05.008

IF: 2.4

2008-01-01

Optics Communications

Abstract:We propose a high birefringence and low loss index-guiding photonic crystal fiber (PCF) using the complex unit cells in cladding by the finite-element method. Results show that the birefringence and confinement loss in such PCF fiber is determined not only by the whole cladding asymmetry but also the shape of the PCF core. The maximal modal birefringence and lowest confinement loss of our proposed structures at the excitation wavelength of λ=1550nm can be achieved at 8.7×10−3 and 5.27×10−5dB/km, respectively.
Material effects in airguiding photonic bandgap fibers

Jesper Laegsgaard,Niels Asger Mortensen,Jesper Riishede,Anders Bjarklev

DOI: https://doi.org/10.48550/arXiv.physics/0307079

2003-07-16

Optics

Abstract:The waveguiding properties of two silica-based airguiding photonic bandgap fiber designs are investigated with special emphasis on material effects. The nonlinear coefficients are found to be 1-2 orders of magnitude smaller than those obtained in index-guiding microstructured fibers with large mode areas. The material dispersion of silica makes a significant contribution to the total chromatic dispersion although less than 10% of the field energy is located in the silica regions of the fibers. These findings suggest that dispersion engineering through the choice of base material may be a possibility in this type of fibers.
Solid Photonic Bandgap Fibres and Applications

J. C. Knight,F. Luan,G. J. Pearce,A. Wang,T. A. Birks,D. M. Bird

DOI: https://doi.org/10.1143/JJAP.45.6059

2006-01-01

Abstract:We report on the development of optical fibres which guide light in a solid core using a photonic bandgap effect. The photonic bandgap cladding consists of a two-dimensional array of isolated high-index regions in a lower-index matrix, with a relatively low index contrast. The core is one or more unit cells of the matrix material without the inclusions. The frequency bands for. photonic bandgap guidance can be predicted by considering the cut-off frequencies of the guided modes of the high-index rods in the cladding using the weakly-guiding approximation. We demonstrate the basic properties of such fibres and their use as a wavelength-selective element in a fibre laser cavity.
Photonic-crystal slabs with a triangular lattice of triangular holes investigated using a guided-mode expansion method

L. C. Andreani,D. Gerace

DOI: https://doi.org/10.48550/arXiv.0706.0395

2007-06-04

Soft Condensed Matter

Abstract:According to a recent proposal [S. Takayama et al., Appl. Phys. Lett. 87, 061107 (2005)], the triangular lattice of triangular air holes may allow to achieve a complete photonic band gap in two-dimensional photonic crystal slabs. In this work we present a systematic theoretical study of this photonic lattice in a high-index membrane, and a comparison with the conventional triangular lattice of circular holes, by means of the guided-mode expansion method whose detailed formulation is described here. Photonic mode dispersion below and above the light line, gap maps, and intrinsic diffraction losses of quasi-guided modes are calculated for the periodic lattice as well as for line- and point-defects defined therein. The main results are summarized as follows: (i) the triangular lattice of triangular holes does indeed have a complete photonic band gap for the fundamental guided mode, but the useful region is generally limited by the presence of second-order waveguide modes; (ii) the lattice may support the usual photonic band gap for even modes (quasi-TE polarization) and several band gaps for odd modes (quasi-TM polarization), which could be tuned in order to achieve doubly-resonant frequency conversion between an even mode at the fundamental frequency and an odd mode at the second-harmonic frequency; (iii) diffraction losses of quasi-guided modes in the triangular lattices with circular and triangular holes, and in line-defect waveguides or point-defect cavities based on these geometries, are comparable. The results point to the interest of the triangular lattice of triangular holes for nonlinear optics, and show the usefulness of the guided-mode expansion method for calculating photonic band dispersion and diffraction losses, especially for higher-lying photonic modes.
Design and analysis of properties of the photonic crystal fibers with chalcogenide glass hollow core

Wenbin Wu

DOI: https://doi.org/10.1117/12.3026937

2024-05-06

Abstract:In the context of photonic crystal fibers used in the field of communication. In this paper, a new design of the photonic crystal fibers is designed and proposed. The analysis of the band-gap of gallium lanthanum suphide glass hollow core photonic crystal fiber is conducted using the plane wave expanding method. Furthermore, the properties of confinement loss and velocity dispersion of the waveguide groups of this kind of fiber are investigated using multiple methods. It is discovered that a band gap of 0.15μm in the mid-infrared band is present in this fiber, and the diameter of the cladding air hole has a significant impact on the confinement loss and the waveguide group velocity dispersion. Last but not the least, we got the confinement loss measures 0.0169dB/m at a wavelength of 2.7μm. This PCF is suitable for research in the mid-infrared wavelength range. This design has great application significance in the fields of fiber optics and optical communication of infrared band.

Materials Science,Engineering,Physics

Air-guiding photonic bandgap fiber with improved triangular air-silica photonic crystal cladding

Submicron and Nano-Diameter Silica Wires for Optical Wave Guiding

Silica Nanofibers and Subwavelength-Diameter Fibers

Mid-infrared dual-cladding photonic crystal fiber with high birefringence and high nonlinearity

Band structure of photonic crystal fibers with silica rings in triangular lattice

Rectangular Porous-Core Photonic-Crystal Fiber With Ultra-Low Flattened Dispersion and High Birefringence for Terahertz Transmission

Simultaneously Achieving a Large Negative Dispersion and a High Birefringence Over Er and Tm Dual Gain Bands in a Square Lattice Photonic Crystal Fiber

Bandgap guidance in hybrid chalcogenide-silica photonic crystal fibers

Refractive-index guiding single crystal optical fiber with air–solid cladding

High Transmitting and Coupling Characteristics of Light at the Surface of A Photonic Crystal with A Triangular Lattice of Air Holes

A New Method of Modeling Cladding Band Structure of Air-Guiding Photonic Crystal Fibers

Ultra-low transmission loss (7.7 dB/km at 750 nm) inhibited-coupling guiding hollow-core photonic crystal fibers with a single ring of tubular lattice cladding

Terahertz Circular Photonic Crystal Fiber

Ultra-large Bandwidth Hollow-Core Guiding in All-Silica Bragg Fibers with Nano-Supports

Quaternary One-Dimensional Photonic Crystal Cladding Hollow-Core Bragg Fiber

Polarization maintaining air-core bandgap terahertz fiber

High Birefringence and Low Loss Circular Air-Holes Photonic Crystal Fiber Using Complex Unit Cells in Cladding

Material effects in airguiding photonic bandgap fibers

Solid Photonic Bandgap Fibres and Applications

Photonic-crystal slabs with a triangular lattice of triangular holes investigated using a guided-mode expansion method

Design and analysis of properties of the photonic crystal fibers with chalcogenide glass hollow core