Abstract:To achieve high-quality friction stir welding (FSW) of the rocket fuel tank, experiments of FSW 18 mm thick 2219 aluminum alloy are carried out, the microstructure and mechanical properties of the joints are studied, and the influence law of the tool rotation speed on microstructure, microhardness and tensile strength of the welded joints are explored. The welding speed used in the experiment is 100 mm/min, and the tool rotation speed is 350 r/min, 400 r/min and 450 r/min, respectively. The microstructure of the weldments is analyzed by optical microscopy and scanning electron microscopy. The mechanical properties are measured by tensile tests and Brinell hardness, and it is found that the mechanical properties of the joint first increased and then decreased with the increase of the tool rotation speed. Due to the uneven temperature distribution along the thickness direction of the weldment, the crystal grains in the nugget zone (NZ) are small equiaxed crystals as a whole, with different local sizes and shapes. The size of the crystal grains seems relatively large in the upper layer and relatively small in the bottom layer. As the tool rotation speed increases, so does the heat generation, and thus, the size and degree of the deformation of the crystal grains increase. The defect appears when the tool rotation speed is 450r/min. As the tool rotation speed increases, the tensile strength and microhardness of the joints increase first and then decrease. The maximum tensile strength of the overall weld is 270 MPa. The microhardness shows a trend of ‘‘U’’ distribution, and the hardness in the NZ is slightly higher than that of thermos-mechanically affected zone (TMAZ) and heat-affected zone (HAZ). The fracture location of the joints is the NZ. The fracture mode is ductile fracture. There exist a large number of second phase particles Al 2 Cu in the dimples.

Microstructure Evolution and Mechanical Properties of FSW SA516 Gr.70 Steel Joints at Different Rotation Rates

Effects of Cooling Media on Microstructure and Mechanical Properties in Friction Stir Welded SA516 Gr.70 Cryogenic Steel Joints

Microstructure evolution and high cycle fatigue failure behavior of friction stir-welded Ti–6Al–4V at varying welding speeds

Microstructure and mechanical properties of FSW medium thickness 2219 aluminum alloy

Effects of Rotational Speed on the Microstructure and Mechanical Properties of 2198-T8 Al-Li Alloy Processed by Friction Spot Welding

Effect of Tool Speed on Microstructure Evolution and Mechanical Properties of Friction Stir Welded Joints of Al-Mg-Si Alloy with High Cu Content

Effect of the Rotation Speed during Friction Stir Welding on the Microstructure and Corrosion Resistance of SAF 2707 Hyper Duplex Stainless Steel

Mechanical Properties and Fracture Behavior of the Refill Friction Stir Spot Welding Dissimilar Aluminum Alloy Joints

Effect of Rotational Velocity on Mechanical and Corrosion Properties of Friction Stir-Welded SUS301L Stainless Steel

Improving microstructural and mechanical properties of dissimilar friction stir welded AZ61/AZ40 joint

Evolution of Strengthening Precipitates During Friction Stir Welding of Al-Zn and Al-Cu Alloys

Microstructure and mechanical properties of friction-stir-welded high-Mg-alloyed Al–Mg alloy plates at different rotating rates

Effect of rotation speed on microstructure and mechanical properties of refill friction stir spot welded 6061-T6 aluminum alloy

Effect of Low Welding and Rotational Speed on Microstructure and Mechanical Behaviour of Friction Stir Welded AZ31-AA6061-T6

Microstructure and abnormal mechanical properties under the coupling effect of strain and temperature for friction-stir-welded joints of Al-Mg-Si alloy

Microstructure and Tensile Strength of AA6082 T-joints by Corner Stationary Shoulder Friction Stir Welding: Effect of Tool Rotation Speed

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Inter-relationship between microstructure evolution and mechanical properties in inertia friction welded 8630 low-alloy steel

Effect of rotation speed on microstructure and mechanical properties of bobbin tool friction stir welded AZ61 magnesium alloy

Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

Microstructure and Mechanical Properties of Ultrahigh‐Speed Friction‐Stir‐Welded Joints of in Situ Al3Zr Particle‐Reinforced Aluminum Matrix Composite Sheets