Abstract:SUMMARY Rotigotine was formulated as extendedrelease implants in this study to achieve CDS for the treatment of PD. The rotigotine-PLGA implants were prepared in two types: hot-melt extrusion implant (HMEI) and in situ forming implant (ISFI). In vivo study of rotigotine HMEI on rats showed a 40-day sustained release with a lag phase which indicated a good potential in clinic application. And ISFI displayed only a 10-day release with high initial burst release. INTRODUCTION Levodopa induced dyskinesias (LID) is a common and troublesome motor complication faced with chronic levodopa therapy in Parkinson’s disease (PD) [1] . Substantial evidence has indicated a relationship between non-physiological or pulsatile stimulation of striatal dopamine receptors and LID in PD. Therefore, continuous dopaminergic stimulation (CDS) has become the focus of the treatment strategy for PD which can prevent the development of dyskinesia and received considerable attention for treatment of PD. However, the currently available CDS treatment options, such as duodenal infusion of L-DOPA (Duodopa®) and rotigotine transdermal delivery system (Neupro®), are associated with disadvantages of poor compliance, high cost or varied efficacy [2] . It is crucial to develop a more convenient and practical means to achieve CDS for the treatment of PD. Rotigotine is a nonergoline agonist of dopamine D3/D2/D1 receptors for the therapy of PD [3] . The present study was designed to prepare a long-acting injection of rotigotine-PLGA implants to provide an alternative of CDS drug delivery. EXPERIMENTAL METHODS The extrusion process was performed with a HAAKE MiniCTW co-rotating twin-screw extruder. Rotigotine and polymer powder blends were manually fed into the preheated barrel. The operating temperature was maintained at 60105°C and the residence time of the materials in the extruder was approximately 0-10 min. Then a 1 mm cylindrical die was used. The produced extrudate was rod-shaped and about 1 mm in diameter. The polymer solutions were prepared by dissolving PLGA in appropriate amounts of DMSO in a vial under intermittent vortexing at room temperature. Designed portion of rotigotine were added to be dissolved just before the in vitro and in vivo experiment. The drug loading of implants was determined by HPLC and the in vitro release was carried out according to orbital shaking bath method. Three replicates of each implant type in separate vials of phosphate-buffered saline on a shaker (37°C, 50 rpm). Samples of 8mL were withdrawn at intervals and replaced with fresh media. The samples were analyzed by HPLC. The external and internal morphology of implants was characterized by the optical microscopic observation and SEM morphology study. Pharmacokinetics evaluation was carried out on rats. A dose of 10 mg/kg rotigotine of HMEI or ISFI was administered subcutaneously. Blood sample were collected pre-dose and at post-dose time points. The samples obtained were immediately centrifuged at 3000 rpm and the plasma was stored at −20°C before analyzed by

Effect of palmitic acid on the characteristics and release profiles of rotigotine-loaded microspheres.

Studying spatial drug distribution in golf ball-shaped microspheres to understand drug release

Study on pramipexole dihydrochloride sustained-release tablets

Preparation of rotigotine-loaded microspheres and its pharmacokinetics in rats

Preparation and characterization of sustained-release rotigotine film-forming gel

Preparation, characterization and in vitro release properties of ibuprofen-loaded microspheres based on polylactide, poly(ε-caprolactone) and their copolymers

Lower irritation microemulsion-based rotigotine gel: formulation optimization and in vitro and in vivo studies

Preparation, Characterization And In Vitro Release Properties Of Ibuprofen-Loaded Microspheres Based On Polylactide, Poly(Epsilon-Caprolactone) And Their Copolymers

Modulating Drug Release from Short Poly(ethylene Glycol) Block Initiated Poly(L-lactide) Di-block Copolymers

Preparation of Rotigotine-Loaded Microspheres and Their Combination Use with L-DOPA to Modify Dyskinesias in 6-Ohda-lesioned Rats

Mechanistic Evaluation of the Opposite Effects on Initial Burst Induced by Two Similar Hydrophilic Additives from Octreotide Acetate Loaded PLGA Microspheres.

Effect of mPEG-PLGA on Drug Crystallinity and Release of Long-Acting Injection Microspheres: In Vitro and In Vivo Perspectives

Development of implants for sustained release of rotigotine to achieve CDS for the treatment of PD

Modulation of Release Rates of Risperidone Loaded Microspheres by Mg(OH)_2

The use of polymorphic state modifiers in solid lipid microparticles: The role of structural modifications on drug release performance

Using Polymers as Crystal Inhibitors to Prevent the Crystallization of the Rotigotine Patch

Effect of drug-polymer interaction on the release characteristics of methacrylic acid copolymer microcapsules containing theophylline

Effect of Bases with Different Solubility on the Release Behavior of Risperidone Loaded Plga Microspheres

Effects Of Gut Microbiota And Ingredient-Ingredient Interaction On The Pharmacokinetic Properties Of Rotundic Acid And Pedunculoside

Preparation of Chlorogenic Acid Loaded Bioadhesive Microspheres and Its Release Profile in Vitro

Effects of Formulation Parameters on Encapsulation Efficiency and Release Behavior of Risperidone Poly(d,l-Lactide-co-glycolide) Microsphere.