Abstract:To reach their full potential, renewable and intermittent energy sources such as wind and sun need to be coupled with a cost effective energy management system that is able to convert, store, and delivery energy as required. The Daniell element is one of the earliest non-rechargeable batteries. It is based on abundant, cost-effective and environmentally-benign materials and the chemistry relies on reduction of copper at the positive electrode and oxidation of zinc at the negative electrode. Since both electrodes are immersed in different electrolytes, they have to be separated by a porous barrier or a salt-bridge in order to prevent the self-discharge of the battery. However, these separators are not selective and copper ions migrate over time to the negative electrode and deposit on the surface of the zinc electrode which reduces shelf time and makes recharging of the element impossible. In this work, we report on a novel Zinc-Copper battery design which is based on the application of a selective cation exchange membrane in conjunction with an unreactive sodium background electrolyte which acts as a charge shuttle. The membrane is impermeable for the copper (and zinc) ions but allows the sodium ions to migrate between the two half-cells to maintain the electro-neutrality. We first tested the suitability of different zinc-based electrolytes, including zinc sulfate, zinc chloride, and zinc nitrate. At equal electrolyte conductivities, we found a higher potential for the zinc deposition in sulfate electrolytes compared to that in chloride electrolytes. It was also observed that the zinc electrode passivated due to the formation of zinc oxide (ZnO) when operated in a zinc nitrate solution. In terms of the electrodeposition of copper, sulfate and nitrate-based electrolytes showed a nearly equal potential. However, chloride-based copper electrolytes shifted the potential to more negative values due to the stabilization of the monovalent copper ion intermediate. The membrane selectivity was evaluated by monitoring the crossover of copper ions into the zinc half-cell for various concentrations of copper in the copper half-cell. After seven days of open circuit operation, we measured copper concentrations below 10 ppm in the zinc half-cell when there was 0.1 M of copper sulfate in the copper half-cell. When the copper half-cell was filled with 0.5 M copper sulfate, the effect of crossover was evident by a blue tint of the electrolyte and the Zn electrode was covered with a layer of black/red deposit. Hence, we chose a conservative catholyte composition of 0.1 M copper sulfate and 1M sodium sulfate in the battery. We performed discharge measurements where we varied the discharge current density and measured the voltage over time. Discharge continued until a cell voltage of 0 V was reached, which corresponds to a complete consumption of the copper ions in the catholyte. Indeed, it turned out that we utilized only around 3 to 6 % of the zinc electrode and less than 1 % of the copper electrode during discharge. These very low values indicate that the present system could also be favorably-designed as a hybrid redox (flow) battery. Hence, for the current preliminary cell design it is seems reasonable to normalize the current with the mass of the initial copper ion content since it is the limiting electro-active species. At 0.5 mA/cm 2 (421 mA/g), the battery was discharged for around 17 hours before all of the copper ions were consumed resulting in a specific capacity of 763 mAh/g. The theoretical charge content based on the initial copper concentration was 843 mAh/g giving a faradaic yield of 90.5 %. The capacity and faradaic yield of the discharge at 1 mA/cm −2 (842 mA/g) were 583 mAh/g and 69.2 %, respectively. The recharge-ability of the battery was investigated over 100 charge-discharge cycles at a current density of ±0.5 mA/cm 2 . The average capacity was 530 mAh/g while the average exergy efficiency was 74 %. The deviations over the cycle numbers are less than 5 % of the average values. In other words, there was no clear increase or decrease during operation, indicating a steady performance. Afterwards, the zinc electrode was characterized using Energy-dispersive X-ray spectroscopy. Only a very small amount of deposited copper was found, indicating a negligible copper ion cross over. This verifies that the combination of a cost-effective monovalent cation exchange membrane along with an unreactive background electrolyte imparts recharge-ability to the Daniell cell. Figure 1

Re-building Daniell Cell with a Li-ion Exchange Film

Re-imagining the daniell cell: ampere-hour-level rechargeable Zn-Cu batteries

A rechargeable zinc copper battery using a selective cation exchange membrane

A Rechargeable Zinc-Copper Battery Based on the Combination of a Monovalent Cationic Exchange Membrane and an Inert Charge Shuttle

Unravelling rechargeable zinc-copper batteries by a chloride shuttle in a biphasic electrolyte

A Replacement Reaction Enabled Interdigitated Metal/Solid Electrolyte Architecture for Battery Cycling at 20 mA cm<SUP>-2</SUP> and 20 mAh cm<SUP>-2</SUP>

An Innovation: Dendrite Free Quinone Paired with ZnMn2O4 for Zinc Ion Storage

Hail to Daniell Cell: From Electrometallurgy to Electrochemical Energy Storage

One-stone, two birds: One step regeneration of discarded copper foil in zinc battery for dendrite-free lithium deposition current collector

Self-repairing interphase reconstructed in each cycle for highly reversible aqueous zinc batteries

Laminated Zinc-Copper Electrodes as Reversible and Dendrite-Free Anodes for Aqueous Rechargeable Zinc-Ion Batteries

A Lithium‐Ion Pump Based on Piezoelectric Effect for Improved Rechargeability of Lithium Metal Anode

A New Type Rechargeable Lithium Battery Based on a Cu-cathode

Reinforcing the Symmetry of Stripping/plating Behavior via In-situ Interface Construction for Long-lasting Zinc Metal Batteries

Environmentally-Friendly Aqueous Li (or Na)-Ion Battery with Fast Electrode Kinetics and Super-Long Life

Synergetic bifunctional Cu-In alloy interface enables Ah-level Zn metal pouch cells

Realizing a Rechargeable High‐Performance Cu–Zn Battery by Adjusting the Solubility of Cu2+

Highly Reversible Zinc Electrodeposition Enabled by Glutathione-Protected Copper Nanoclusters for Aqueous Zn-Ion Batteries

Redistributing Zinc-Ion Flux by Constructing a Hybrid Conductor Interface for Dendrite-Free Zinc Anode

Regulating electrodeposition morphology in high-capacity aluminium and zinc battery anodes using interfacial metal–substrate bonding

A Bio-inspired Electrolyte with in situ Repair of Zn Surface Crack and Regulation of Zn ion Solvation Chemistry to Enable Long-life and Deep-cycling Zinc Metal Batteries