Abstract:Interface failure is common in structures consisting of dissimilar materials. Interface stresses arise due to the mismatch of mechanical properties during processing or usage which often results in fracture. While much progress has been made in understanding the interface fracture in hard materials, relatively little is known about the fracture mechanics of soft matter. A familiar yet challenging example is the drying of a colloidal film.Drying has been exploited as a unique and simple preparation technique for colloidal coatings, such as paint, for thousands of years. As solvent evaporates the suspension undergo a fluid to solid transition far away from equilibrium. Enormous stresses build up during drying that often leads to the failure of thin films. The heterogeneous nature of drying makes it difficult to understand the mechanics because the composition and properties vary dramatically in space and time.By utilizing and improving "traction force microscopy" used in cell biology to measure the force generated by crawling cells, we quantify the spatial distribution of all three components of stress at the interface between drying colloidal films and their substrates. Particularly, we apply this approach to image stresses and strain near the tip of interface and in-plane cracks. With this technique, we are able to better understand the evolution of mechanical properties and fracture mechanics.We recently reported the stresses and deformation profile near the tip of an interface crack between the drying colloidal coating and the elastomer substrate and measured the stress intensity factor [I]. Both normal and in-plane stresses on the interface were carefully measured using the deformation of elastomer substrate. Furthermore, the local strain of drying colloidal films can also be measured by analyzing the displacements of tracer particles inside the films. Our goal is to correlate the stresses on the interface and the strain of drying films near the interface so that we can establish the constitutive relationships which are left largely unknown for drying colloidal films.Using the same technique, we are also studying drying and cracking films consisting of other colloidal particles, such as corn starch. Drying starch suspension is a nice and simple model system to study the fracture dynamics and mechanics. We coat a thin layer of starch-water mixture on our elastomer substrate. It gradually solidifies and forms a nice cracking pattern while deforming the elastomer substrate underneath it. Fig. I shows one region of cracks in dried corn starch, superimposed with substrate deformation field, from which the distribution of stresses on the interface can be calculated using the solution we presented in [1]. In addition, the relatively larger size of starch particles will enable us to resolve the microstructure of the dried films and understand the effect of particle properties on the drying and cracking behaviors of colloidal films.Our technique is quite general and can be applied in studying other phenomenon involving interface mechanics such as adhesion, and is particularly valuable for materials with spatially and temporally heterogeneous mechanical properties. It can be adapted to measure interface stresses over a wide dynamic range by changing the elastic modulus of the elastomer substrate.

Surface wrinkling and cracking dynamics in the drying of colloidal droplets

Pattern Transition and Sluggish Cracking of Colloidal Droplet Deposition with Polymer Additives

Drying-Induced Cracks in Thin Film Fabricated from Colloidal Dispersions

Drying crack patterns of sessile drops with tuned contact line

Surface Roughness Induced Cracks of the Deposition Film from Drying Colloidal Suspension

Crack densification in drying colloidal suspensions

Dewetting of Polymer Films with Built-In Topographical Defects

Interplay of Consolidation Fronts and Cracks in Drying Colloidal Coatings and Its Application in Controlling Crack Pattern Formation.

Role of evaporation rate on the particle organization and crack patterns obtained by drying a colloidal layer

Cracking to Curling Transition in Drying Colloidal Films

Surface patterns in drying films of silica colloidal dispersions

Eliminating cracking during drying

Formation Mechanism of Radial and Circular Cracks Promoted by Delamination in Drying Silica Colloidal Deposits

Rupturing of Polymer Films with Rubbing-Induced Surface Defects

Pattern Formation Mechanism Via Evaporation of Colloidal Droplet Containing Ptfe Particles and Nacl

Polymer-Mediated Crack Suppression in Deposit of Nanoellipsoids

Suppression of cracking in drying colloidal suspensions with chain-like particles

Tuning Crack Pattern by Phase Separation in the Drying of Binary Colloid–polymer Suspension

Imaging Interface Stress and Strain in Heterogeneous Films

Drying-induced stresses in poroelastic drops on rigid substrates

Imaging stress and strain in the fracture of drying colloidal films