Abstract:The aim of this study was to develop new materials with adsorbent properties that can be used for the adsorption recovery of Au(III) from aqueous solutions. To achieve this result, it is necessary to obtain inexpensive adsorbent materials in a granular form. Concomitantly, these materials must have a high adsorption capacity and selectivity. Other desired properties of these materials include a higher physical resistance, insolubility in water, and materials that can be regenerated or reused. Among the methods applied for the separation, purification, and preconcentration of platinum-group metal ions, adsorption is recognised as one of the most promising methods because of its simplicity, high efficiency, and wide availability. The studies were carried out using three supports: cellulose (CE), chitosan (Chi), and diatomea earth (Diat). These supports were functionalised by impregnation with extractants, using the ultrasound method. The extractants are environmentally friendly and relatively cheap amino acids, which contain in their structure pendant groups with nitrogen and sulphur heteroatoms (aspartic acid—Asp, l-glutamic acid—Glu, valine—Val, DL-cysteine—Cys, or serine—Ser). After preliminary testing from 75 synthesised materials, CE-Cys was chosen for the further recovery of Au(III) ions from aqueous solutions. To highlight the morphology and the functionalisation of the material, we physicochemically characterised the obtained material. Therefore, the analysis of the specific surface and porosity showed that the CE-Cys material has a specific surface of 4.6 m2/g, with a porosity of about 3 nm. The FT-IR analysis showed the presence, at a wavelength of 3340 cm−1, of the specific NH bond vibration for cysteine. At the same time, pHpZc was determined to be 2.8. The kinetic, thermodynamic, and equilibrium studies showed that the pseudo-second-order kinetic model best describes the adsorption process of Au(III) ions on the CE-Cys material. A maximum adsorption capacity of 12.18 mg per gram of the adsorbent material was achieved. It was established that the CE-Cys material can be reused five times with a good recovery degree.

Selective adsorption and recovery of Au(III) from three kinds of acidic systems by persimmon residual based bio-sorbent: a method for gold recycling from e-wastes.

Effective and Selective Recovery of Au(III) from WPCBs Using Quaternary Phosphonium Adsorbent Synthesized by Adjusting Steric Hindrance

Adsorptive recovery of Au(III) from aqueous solution using crosslinked polyethyleneimine resins

Efficient and selective capture of Au(III) from PCBs by pentaethylenehexamine-modified chloromethylated polystyrene beads

Selectivity of modified pomegranate peel for gold, platinum, and palladium: Adsorption behavior, mechanism, and recovery

Highly efficient gold recovery from electronic waste through employing 3D printed Polyethylenimine/graphene oxide/calcium alginate multilevel Macroporous adsorbent

Immobilization of ionic liquids onto chloromethylated polystyrene as a strategy for highly efficient and selective recovery of Au(III) from gold slag and PCBs

Selective Recovery of Gold from Electronic Circuit Board Waste with Pyrogallol-Formaldehyde Polymer

Highly Efficient and Selective Gold Recovery Based on Hypercross-Linking and Polyamine-Functionalized Porous Organic Polymers

Constructing a cationic pyridine for the highly selective and efficient recovery of gold from waste printed circuit boards

Selective and highly efficient recovery of Au(III) by poly(ethylene sulfide)-functionalized UiO-66-NH2: Characterization and mechanisms

Chitosan-thioglycolic acid composite cross-linked with glutaraldehyde for selective recovery of Au(III) ions from e-waste leachate via reduction-coupled adsorption and incineration

Gold recovery from printed circuit board waste using coal gasification slag

Highly efficient and selective recovery of Au(III) by cellulose microspheres bearing nucleobase and their applications in gold slag treatment

Efficient and Selective Recovery of Au(III) from Aqueous Solution by Functionalized UiO-67 Materials: Cooperative Effects of Diamino-Functionalization and Charge Modulation

Synthesis of Some Eco-Friendly Materials for Gold Recovery

Optimal CDMA: Fundamentals, developments, and applications

Design and preparation of novel functional resin D301-g-polyvinylimidazole for recovering Au(III) from aqueous solution

Selective recovery of gold from dilute aqua regia leachate of waste printed circuit board by thiol-modified garlic peel

Highly effective and selective adsorption of Au(III) from aqueous solution by poly(ethylene sulfide) functionalized chitosan: Kinetics, isothermal adsorption and thermodynamics

Recycling gold from printed circuit boards gold-plated layer of waste mobile phones in “mild aqua regia” system