Electrical, enzymatic graphene biosensing of 5-aminosalicylic acid.

Pratima Labroo,Yue Cui

DOI: https://doi.org/10.1039/c3an36660j

2013-01-01

Abstract:We present an electrical biosensing of 5-aminosalicylic acid (5-ASA) based on a peroxidase-immobilized graphene sensor on a microfluidic paper. The sensor shows a sensitive detection range from 0.5 to 20 μM and a total measuring time of 2 min with a simple fabrication procedure.

What problem does this paper attempt to address?

Development of glucose biosensors based on nanostructured graphene-conducting polyaniline composite.

Xue Feng,Huijun Cheng,Yiwen Pan,Hao Zheng

DOI: https://doi.org/10.1016/j.bios.2015.03.046

IF: 12.545

2015-01-01

Biosensors and Bioelectronics

Abstract:A biosensor was fabricated by immobilizing glucose oxidase (GOD) into nanostructured graphene (GRA)-conducting polyaniline (PANI) nanocomposite, which was based on electrochemical polymerization of aniline in GRA synthesized by using electrochemical expansion of graphite in propylene carbonate electrolyte. Scanning electron spectroscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to characterize the morphology and performance of the as-prepared biosensor, respectively. Amperometric measurements were carried out to optimize test conditions (pH and applied potential) of the biosensor. Under the optimal conditions, the biosensor showed a linear range from 10.0μM to 1.48mM (R2=0.9988) with a sensitivity of 22.1μAmM−1cm−2, and a detection limit of 2.769μM (S/N=3). The apparent Michaelis–Menten constant (KMa) was estimated to be 3.26mM. The interference from glycine (Gly), D-galactose (D-Gal), urea (Urea), L-phenylalanine (L-Phe), ascorbic acid (AA), and L-tyrosine (L-Tyr) was also investigated. The results indicated that the biosensor exhibit high sensitivity and superior selectivity, providing a hopeful candidate for glucose biosensing.
Fabrication of iron tin oxide/tin oxide intertwined graphitic carbon nitride hybrid composite electrocatalyst for electrochemical detection of 5-aminosalicylic acid in human urine and pharmaceutical tablet samples

Sivakumar Musuvadhi Babulal,Lakshmipriya Musuvadhi Babulal,Shen-Ming Chen,Chelladurai Karuppiah,Chun-Chen Yang

DOI: https://doi.org/10.1016/j.jtice.2023.104837

IF: 5.477

2023-04-04

Journal of the Taiwan Institute of Chemical Engineers

Abstract:Highlights • Iron tin oxide/tin oxide nanostructures were synthesized by precipitation approach • A novel hybrid FSO/SO/g-C 3 N 4 composite was obtained by a wet chemical approach. • The synergistic effect between FSO/SO and gC 3 N 4 exhibits enhance electrocatalytic performance. • FSO/SO/g-C 3 N 4 /GCE exhibited good recoveries resulting in the detection of 5-ASA. Background 5-Aminosalicylic acid (5-ASA) is known as a cornerstone in the treatment of inflammatory bowel diseases, to prevent the synthesis of cytokines and inflammatory mediators. However, an overdose of this drug is a rare and unique condition in patients and can lead to kidney failure. Therefore, a rapidly sensitive method is needed for the monitoring of 5-ASA. Methods we synthesized novel iron tin oxide/tin oxide (FeSnO 3 /SnO 2 , FSO/SO) nanostructures via a facile precipitation method. Further, the FSO/SO intertwined two-dimensional (2D) graphitic carbon nitride (g-C 3 N 4 ) hybrid composite electrocatalyst was developed by the wet-chemical process. The proposed materials were characterized by XRD, Raman, XPS, FESEM, TEM and TGA. Further, the glassy carbon electrode (GCE) modified with FSO/SO/g-C 3 N 4 was revealed to sensitive detection of 5-ASA in PBS (pH-7) by CV, LSV and DPV methods. Significant findings The surface modification of FSO/SO/g-C 3 N 4 /GCE can enhance the synergistic action of different dimensional active catalysts. The limit of detection (LOD=3σ/S) proposed sensor was found to be 0.00625 μM and 0.0075 μM via LSV and DPV methods, also the calculated sensitivity has 3.428 μA μM −1 cm −2 and 2.857 μA μM −1 cm −2 respectively. The developed sensor demonstrated outstanding feasibility test results for detecting 5-ASA in samples of human urine and mesalamine tablet using the DPV method. Graphical Download : Download high-res image (221KB) Download : Download full-size image

engineering, chemical
Graphene-Based Flexible Sensors for Simultaneous Detection of Ascorbic Acid, Dopamine, and Uric Acid

Shuaishuai Meng,Yaming Liu,Li Wang,Xixi Ji,Yun Chen,Tingting Zheng,Jie Yu,Huanhuan Feng

DOI: https://doi.org/10.3389/fbioe.2021.726071

IF: 5.7

2021-09-20

Frontiers in Bioengineering and Biotechnology

Abstract:Many diseases are closely related to abnormal concentrations of ascorbic acid (AA), dopamine (DA), and uric acid (UA). Therefore, the detection of these small molecules is significant for monitoring life metabolism and healthy states. Electrochemical detection has been widely used to detect small molecules due to its good selectivity, high sensitivity, and good economics. Fabrication and application are two sides of the coin, and we cannot give up one for the other. Graphene (GN) is a very suitable material for electrochemical sensing due to its excellent catalytic performance and large specific surface area. It possesses many excellent properties but cannot hold itself alone due to its nanoscale thickness. Herein, we have fabricated three-dimensional (3D) GN nanosheets (GNSs) on flexible carbon cloth (CC) by thermal chemical vapor deposition (CVD). The GNSs/CC can successfully detect AA, DA, and UA simultaneously. We find that these GNSs/CC sensors show good performance with 7 h CVD modification. The linear ranges of AA, DA, and UA are 0.02–0.1, 0.0005–0.02, and 0.0005–0.02 mM, respectively. The detection sensitivity rates of AA, DA, and UA are 5,470, 60,500, and 64,000 μA mM −1 cm −2 , respectively. Our GNSs/CC flexible sensors can be successfully applied in the human serum for UA detection. The result matches with commercial sensors very well.

multidisciplinary sciences
Facile Assembly of Graphene on Anion Exchange Resin Microspheres for Electrochemical Sensing and Biosensing.

Shijun Sheng,Shuang Liu,Luyan Zhang,Gang Chen

DOI: https://doi.org/10.1002/asia.201200745

2012-01-01

Abstract:Graphene sheets were assembled on anion exchange resin (AER) microspheres based on the electrostatic interactions between graphene oxide and AER and subsequent chemical reduction. The prepared graphene-coated AER microspheres were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. They were then embedded in the bores of pipette tips to fabricate disposable electrodes for electrochemical sensing. The workability and performance of the novel electrodes were examined by analyzing the electrochemical behavior of the electrodes for the sensing of ascorbic acid, dopamine, uric acid, acetaminophen, aniline, and glucose by cyclic voltammetry and amperometry. The advantages of the electrodes include ease of fabrication, low cost, pronounced electrocatalytic activity, and rapid response. Thus, they hold great promise for a wide range of applications.
Bio-agent free electrochemical detection of Salicylic acid

Bhuwan Kashyap,Ratnesh Kumar

DOI: https://doi.org/10.1109/sensors43011.2019.8956497

2019-10-01

Abstract:Salicylic acid is an important chemical used in various industries including pharmaceutical, cosmetic, food and agriculture. It is a key phytohormone responsible for initiating and regulating defense mechanisms against biotic as well as environmental stress in plants. It is a major component of Aspirin, a common anti-inflammatory, anti-pyretic and analgesic drug whose overusage and mis-dosage can lead to various health problems in humans. In this work, a novel electro-reduced graphene oxide modified screen printed carbon electrode electrochemical sensor has been presented for the detection of salicylic acid based on its electro-oxidation. The proposed device offers an inexpensive, sensitive, selective, quick responding, rapid and easy to fabricate sensor to salicylic acid measurement with excellent performance. The proposed sensor is capable of measuring concentrations from 2 to 512 µM with a maximum sensitivity of 600 µA/mM/cm2 with high (piece-wise) linearity, and was used to determine salicylic acid level in fresh orange juice with 99% accuracy.
Performance Enhancement of SPR Biosensor Using Graphene–MoS2 Hybrid Structure

Haoyuan Cai,Mengwei Wang,Zhuohui Wu,Jing Liu,Xiaoping Wang

DOI: https://doi.org/10.3390/nano12132219

IF: 5.3

2022-01-01

Nanomaterials

Abstract:We investigate a high-sensitivity surface plasmon resonance (SPR) biosensor consisting of a Au layer, four-layer MoS2, and monolayer graphene. The numerical simulations, by the transfer matrix method (TMM), demonstrate the sensor has a maximum sensitivity of 282°/RIU, which is approximately 2 times greater than the conventional Au-based SPR sensor. The finite difference time domain (FDTD) indicates that the presence of MoS2 film generates a strong surface electric field and enhances the sensitivity of the proposed SPR sensor. In addition, the influence of the number of MoS2 layers on the sensitivity of the proposed sensor is investigated by simulations and experiments. In the experiment, MoS2 and graphene films are transferred on the Au-based substrate by the PMMA-based wet transfer method, and the fabricated samples are characterized by Raman spectroscopy. Furthermore, the fabricated sensors with the Kretschmann configuration are used to detect okadaic acid (OA). The okadaic acid–bovine serum albumin bioconjugate (OA-BSA) is immobilized on the graphene layer of the sensors to develop a competitive inhibition immunoassay. The results show that the sensor has a very low limit of detection (LOD) of 1.18 ng/mL for OA, which is about 22.6 times lower than that of a conventional Au biosensor. We believe that such a high-sensitivity SPR biosensor has potential applications for clinical diagnosis and immunoassays.
An Electrochemical Immunosensor Based on SPA and rGO-PEI-Ag-Nf for the Detection of Arsanilic Acid

Yanwei Wang,Dongdong Ma,Gaiping Zhang,Xuannian Wang,Jingming Zhou,Yumei Chen,Xiaojuan You,Chao Liang,Yanhua Qi,Yuya Li,Aiping Wang

DOI: https://doi.org/10.3390/molecules27010172

IF: 4.6

2021-12-28

Molecules

Abstract:A sensitive electrochemical immunosensor was prepared for rapid detection of ASA based on arsanilic acid (ASA) monoclonal antibody with high affinity. In the preparation of nanomaterials, polyethyleneimine (PEI) improved the stability of the solution and acted as a reducing agent to generate reduced graphene oxide (rGO) with relatively strong conductivity, thereby promoting the transfer of electrons. The dual conductivity of rGO and silver nanoparticles (AgNPs) improved the sensitivity of the sensor. The synthesis of nanomaterials were confirmed by UV-Vis spectroscopy, X-ray diffraction, transmission electron microscopy and scanning electron microscopy. In the optimal experiment conditions, the sensor could achieve the detection range of 0.50–500 ng mL−1 and the limit of detection (LOD) of 0.38 ng mL−1 (S/N = 3). Moreover, the sensor exhibited excellent specificity and acceptable stability, suggesting that the proposed sensor possessed a good potential in ASA detection. Thus, the as-prepared biosensor may be a potential way for detecting other antibiotics in meat and animal-derived foods.

chemistry, multidisciplinary,biochemistry & molecular biology
Electrochemical ascorbic acid sensor based on DMF-exfoliated graphene

Gareth P. Keeley,Arlene O'Neill,Niall McEvoy,Nikos Peltekis,Jonathan N. Coleman,Georg S. Duesberg

DOI: https://doi.org/10.1039/c0jm01527j

2010-01-01

Journal of Materials Chemistry

Abstract:This paper describes the electron transfer properties of graphene nano-sheets (GNSs) immobilised on pyrolysed photoresist film (PPF) electrodes. The former are produced by the dispersion and exfoliation of graphite in dimethylformamide, and they are characterised using transmission electron microscopy, scanning electron microscopy and Raman spectroscopy. Cyclic voltammetry and electrochemical impedance spectroscopy are used to quantify the effect of the GNSs on electrochemical surface area and on electron transfer kinetics. Compelling evidence is reported in relation to the importance of edge-plane sites and defects in the promotion of electron transfer at carbon nanostructures. A novel ascorbic acid (vitamin C) sensor is presented based on the PPF/GNS system, which is effective in the range 0.4 to 6.0 mM, with a 0.12 mM detection limit. The selectivity of the sensor is demonstrated using a commercially available vitamin C supplement. This is the first report of the electrochemical properties of graphene nano-sheets produced using liquid-phase exfoliation, and it will serve as an important benchmark in the development of inexpensive graphene-based electrodes with high surface area and electro-catalytic activity.
Graphene quantum dots mediated acrylamide biosensing

Shatrughan Aafria,Minakshi Sharma

DOI: https://doi.org/10.1016/j.microc.2024.110956

IF: 5.304

2024-06-15

Microchemical Journal

Abstract:Acrylamide (AA) is an unwanted food processing contaminant produced during cooking at high temperatures through the Maillard reaction between asparagine and reducing sugars or reactive carbonyls. In humans, it causes significant neurotoxicity, genotoxicity, and possible carcinogenicity. AA is categorized as a 'Group 2A' carcinogen by the International Agency for Research on Cancer (IARC). Bread, biscuits, and potato crisps are examples of foods heavy in starch that contain significant quantities of AA. Consequently, the detrimental effects of AA on human health make determining its quantitative content a crucial matter. Here, by immobilizing Hemoglobin nanoparticles (HbNPs) onto graphene quantum dots (GQDs) decorated pencil graphite (PG) electrode, we have developed a highly sensitive electrochemical biosensor for the detection of AA. Using cyclic voltammetry (CV), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS), the developed working electrode (HbNPs/GQDs/PG) was examined at different stages of its preparation. The ideal pH and temperature for the fabricated biosensor were 5.0 and 35 °C, respectively and the biosensor demonstrated an acceptable level of selectivity, sensitivity, and stability along with a broad linear range (10 nM to 120 nM) and a low detection limit of 2.70 nM. The suggested strategy made use of less costly raw materials to ensure that it should be both effective and environmentally friendly. The sensor was effectively used to measure the amounts of AA in potato crisp samples.

chemistry, analytical
Computationally Optimized Graphene-Based Electrochemical Sensor with Enhanced Signal Stability for the Determination of the Antimicrobial Agent 9-aminoacridine

Martin N. Saad,Hoda Allah M. Marzouk,Sawsan M Amer,Ibrahim M. El-Sherbiny,Amr M. Mahmoud

DOI: https://doi.org/10.1149/1945-7111/ad8522

IF: 3.9

2024-10-11

Journal of The Electrochemical Society

Abstract:A hydrophobic aryl diazonium salt has been synthesized from 3,5-bis(trifluoromethyl)aniline and utilized to covalently modify graphene nanoplatelets and carbon nanotubes. The modified nanomaterials were applied on a screen-printed electrode/ion sensing membrane interface resulting in reduced potential drift to 100 μV/h compared to control sensors. Characterization was achieved through X-ray photoelectron spectroscopy. The electrode's response was optimized using response surface methodology and then utilized for determination of 9-Aminoacridine (9-AA) in pharmaceutical gel dosage form and spiked human plasma without prior extraction steps. 9-AA is a fluorescent dye with antimicrobial activity that eradicates a range of microorganisms that can cause oral sores or broken skin and it has been recently used as anticancer among other uses as fluorescent dye and pH indicator. Accurate determination of 9-AA could help in adjusting dosages for each application. The optimized sensor was validated per IUPAC guidelines and obtained a wide linearity range from 1.0 × 10–7 M to 1.0 × 10–2 M, correlation coefficient of 0.9997, improved Nernstian slope 59.72, long term stability, and lower limit of detection (9.0 × 10–8 M). Furthermore, Analytical Eco-scale and AGREE methods were utilized to evaluate the presented method's greenness.

electrochemistry,materials science, coatings & films
Self-Reduction of Bimetallic Nanoparticles on Flexible Mxene-Graphene Electrodes for Simultaneous Detection of Ascorbic Acid, Dopamine, and Uric Acid

Ying Wang,Peng Zhao,Bo Gao,Min Yuan,Jiabing Yu,Zeping Wang,Xianping Chen

DOI: https://doi.org/10.2139/ssrn.4163714

2022-01-01

SSRN Electronic Journal

Abstract:Three-dimensional (3D) porous laser-scribed graphene (LSG) is potential electrode material for flexible electrochemical sensor own to its high-efficiency preparation and low cost. However, the growth of nanoparticles usually depends on reducers or harsh conditions, which limit the application in flexible biosensor. To solve this drawback, we applied 2D MXene nanosheets to functionalize 3D LSG sheets with a C-O-Ti covalent crosslink and obtain an LSG-MXene hybrid scaffold. We synthesized the shape-controlled Au-Pd bimetallic nanoparticles on the surface of LSG-MXene by a self-reduction process at room temperature in 6 minutes to enhance its catalytic performance. As a proof of concept, the obtained hybrid nanocomposite can assess Ascorbic Acid (AA,10-1600 μM), Dopamine (DA,12-240 μM), and Uric Acid (UA, 8-800 μM). The fabricated sensor exhibited a low detection limit (S/N = 3) of 3 μM AA, 0.13 μM DA, and 1.47 μM UA. Furthermore, the Au-Pd/MXene/LSG was successfully applied to determine AA, DA, and UA in urine samples with satisfactory. Predictable, these outstanding performance sensors have great potential in terms of flexible and wearable electronics.

English Else
A Hydrothermal Synthesis of Graphene Quantum Dots Modified Carbon Paste Electrode as an Efficient Electro Sensor Towards L-Ascorbic Acid

S. Durairaj,R. Kulandaivelu

DOI: https://doi.org/10.14233/AJCHEM.2019.21809

2019-05-25

Asian Journal of Chemistry

Abstract:The tremendous electronic assets of graphene, with its charge carriers parroting relativistic graphene quantum dots and its potential in numerous applications, have ensured a hasty evolution of interest in this ground-breaking material. The graphene quantum dots, in the size range of 1-5 nm, showed 0 D morphology, which exists with few atomic layers of wideness and have zigzag edge structure. Herein, We report on electrochemical behaviour of graphene quantum dots modified electrode that hold edges and basal plane content, accelerated the anodic peak current with a sensitivity of about 0.68 mA mM–1 and offers 1.4 times higher sensitivity towards the oxidation of ascorbic acid.

Materials Science,Chemistry
Fabrication of a salivary amylase electrochemical sensor based on surface confined MWCNTs/β-cyclodextrin/starch architect for dental caries in clinical samples

Hira Asghar,Aqsa Tariq,Ghulam Rasool,Akhtar Hayat

DOI: https://doi.org/10.1016/j.bioelechem.2024.108774

IF: 5.76

Bioelectrochemistry

Abstract:Salivary α-amylase (α-ALS) has drawn attention as a possible bioindicator for dental caries. Herein, combining the synergistic properties of multi-walled carbon nanotubes (MWCNTs), β-cyclodextrin (β-CD) and starch, an electrochemical sensor is constructed employing ferrocene (FCN) as an electrochemical indicator to oversee the progression of the enzymatic catalysis of α-ALS. The method involves a two-step chemical reaction sequence on a screen-printed carbon electrode (SPCE). X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Field emission scanning electron microscope (FE-SEM), and Dynamic light scattering (DLS) were used to characterize the synthesized material, while Static water Contact angle measurements, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) were performed to monitor each step of sensor fabrication. The electrochemical sensor permitted to detect α-ALS within the linear range of 0.5-280 U mL-1, revealing detection (LOD), and quantification (LOQ) values of 0.041 U mL-1, and 0.159 U mL-1, respectively. Remarkably, the sensor demonstrated exceptional specificity and selectivity, effectively discriminating against other interfering substances in saliva. Validation of the method involved analyzing α-ALS levels in artificial saliva with an accuracy range of 97 % to 103 %, as well as in real clinical saliva samples across various age groups.
A Portable Microelectrochemical Sensor Based on Potentiostatic Polarization-Treated and Laser-Induced Graphene for the Simultaneous Determination of Ascorbic Acid, Dopamine, and Uric Acid

Xiaoming Yuan,Xiu-Wen Wu,Shilin Li,Ruwei Liu,Yunhan Ling

DOI: https://doi.org/10.1021/acs.langmuir.4c03269

2024-01-01

Abstract:Maintaining normal biomolecular levels in the human body plays a crucial role in controlling various diseases. In this work, we designed a portable microelectrochemical sensor based on laser-induced graphene (LIG) for the simultaneous determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). A simple electrode surface modification strategy, potentiostatic polarization in an alkali solution, was applied to functionalize the LIG surface with the aim of enhancing the LIG electrocatalytic activity, conductivity, and wettability. After electrochemical pretreatment, the modified electrode displayed significantly enhanced electrocatalytic activity toward AA, DA, and UA, with well-separated characteristic oxidation peaks for each analyte, thus achieving their simultaneous detection without further modification by nanomaterials. Differential pulse voltammetry (DPV) was applied for determining these three analytes. Under optimal conditions, calibration curves were obtained in the ranges 10-5000 μM, 0.1-6000 μM, and 10-8000 nM for AA, DA, and UA, with the detection limits (S/N = 3) of 1.43 μM, 6.83 nM, and 1.07 nM, respectively. The microelectrochemical sensor achieved reliable and satisfactory results in detecting AA, DA, and UA in actual urine samples, demonstrating significant application prospects in human health monitoring and clinical diagnosis.
3D Graphene Foams Decorated by CuO Nanoflowers for Ultrasensitive Ascorbic Acid Detection.

Ye Ma,Minggang Zhao,Bin Cai,Wei Wang,Zhizhen Ye,Jingyun Huang

DOI: https://doi.org/10.1016/j.bios.2014.03.064

2014-01-01

Abstract:When the in vitro research works of biosensing begin to mimic in vivo conditions, some certain three-dimensional (3D) structures of biosensors are needed to accommodate biomolecules, bacteria or even cells to resemble the in vivo 3D environment. To meet this end, a novel method of synthesizing CuO nanoflowers on the 3D graphene foam (GF) was first demonstrated. The 3DGF/CuO nanoflowers composite was used as a monolithic free-standing 3D biosensor for electrochemical detection of ascorbic acid (AA). The 3D conductive structure of the GF is favorable for current collection, mass transport and loading bioactive chemicals. And CuO nanoflowers further increase the active surface area and catalyze the redox of AA. Thus, all these features endows 3DGF/CuO composite with outstanding biosensing properties such as an ultrahigh sensitivity of 2.06 mA mM(-1) cm(-2) to AA at 3 s response time.
Facile Electrochemical Biosensing Platform Based on Laser Induced Graphene/Laccase Electrode for the Effective Determination of Gallic Acid

Xi Lin,Yuchen Zhou,Zhenfeng Lei,Rui Chen,Wanchun Chen,Xiangying Meng,Yanxia Li

DOI: https://doi.org/10.3390/pr11072048

IF: 3.5

2023-07-10

Processes

Abstract:In this study, a facile electrochemical biosensing platform was fabricated with Laccase (Lac) immobilized on laser-induced graphene (LIG) electrode by glutaraldehyde covalently binding for the effective determination of gallic acid (GA). The patterned graphene for the LIG electrode was prepared by a one-step laser direct writing on the polyimide film in ambient air. The sheet layer and spatial mesh structures of LIG give the prepared LIG electrode a large specific surface area and good conductivity. The oxygen enrichment and good hydrophilicity cause LIG to favor covalent crosslinking with laccase through glutaraldehyde. The electrochemical sensor of GA on the prepared electrode was determined by chronoamperometry. Results show that the current signals of the laccase electrodes had an excellent linear relationship with GA in the concentration range of 0.1–20 mmol/L with a detection limit of 0.07 mmol/L under optimized experimental conditions. The prepared GA sensor with good selectivity, regeneration, and stability can be applied to biological samples such as sweat, urine and serum without needing sample pretreatment.

engineering, chemical
Graphene Oxide/Multiwalled Carbon Nanotubes Composites As an Enhanced Sensing Platform for Voltammetric Determination of Salicylic Acid

Limin Lu,Xiaofei Zhu,Xinlan Qiu,Haohua He,Jingkun Xu,Xiaoqiang Wang

DOI: https://doi.org/10.1016/s1452-3981(23)11026-1

IF: 1.541

2014-01-01

International Journal of Electrochemical Science

Abstract:In this paper, a study of the electrocatalytic oxidation of salicylic acid (SA) at graphene oxide/multiwalled carbon nanotubes (GO/MWCNTs) modified electrode is presented. Compared to GO or MWCNTs electrodes, the electro- oxidation of SA significantly enhanced at the GO/MWCNTs electrode, accounting for the synergistic effect of MWCNTs and GO, in which MWCNTs increased the electronic conductivity and GO provided a large specific surface area to increase the loading amount of SA. Then the GO/MWCNTs electrode was applied for the electrochemical determination of SA in PBS at pH 6.5. Under the optimized conditions, the oxidation peak current was proportional to SA concentration in the range of 0.08 mu M to 150 mu M with a detection limit of 0.03 mu M (S/N = 3). Moreover, the modified electrode showed high selectivity, good stability and reproducibility.
Electrochemical sensor based on nitrogen doped graphene: simultaneous determination of ascorbic acid, dopamine and uric acid.

Zhen-Huan Sheng,Xiao-Qing Zheng,Jian-Yun Xu,Wen-Jing Bao,Feng-Bin Wang,Xing-Hua Xia

DOI: https://doi.org/10.1016/j.bios.2012.01.030

IF: 12.545

2012-01-01

Biosensors and Bioelectronics

Abstract:Nitrogen doped graphene (NG) was prepared by thermally annealing graphite oxide and melamine mixture. After characterization by atomic force microscopy and X-ray photoelectron spectroscopy etc., the electrochemical sensor based on NG was constructed to simultaneously determine small biomolecules such as ascorbic acid (AA), dopamine (DA) and uric acid (UA). Due to its unique structure and properties originating from nitrogen doping, NG shows highly electrocatalytic activity towards the oxidation of AA, DA and UA. The electrochemical sensor shows a wide linear response for AA, DA and UA in the concentration range of 5.0×10−6 to 1.3×10−3M, 5.0×10−7 to 1.7×10−4M and 1.0×10−7 to 2.0×10−5M with detection limit of 2.2×10−6M, 2.5×10−7M and 4.5×10−8M at S/N=3, respectively. These results demonstrate that NG is a promising candidate of advanced electrode material in electrochemical sensing and other electrocatalytic applications.
Electrochemical Sensing Platform Based on Three-Dimensional Holey Graphene for Highly Selective and Ultra-Sensitive Detection of Ascorbic Acid, Uric Acid, and Nitrite

Zhenfei Chen,Yan Zhang,Jing Zhang,Jian Zhou

DOI: https://doi.org/10.1149/2.1111910jes

IF: 3.9

2019-01-01

Journal of The Electrochemical Society

Abstract:In this paper, three-dimensional holey graphene (3D-HG) was used to fabricate a sensitive electrochemical sensing platform. Three-dimensional holey graphene with a 3D porous network and in-plane nanopores possesses a large surface area and more exposed edge planes, contributing to a remarkable increase of electrochemically active sites and of electron-transfer rate. As a result, the excellent electrocatalytic activities of 3D-HG modified electrode toward ascorbic acid (AA), uric acid (UA), and nitrite oxidation were observed. This sensor showed excellent properties for AA, UA and nitrite detection using differential pulse voltammograms, including low detection limits, wide linear ranges and high sensitivities. Moreover, the applicability of 3D-HG modified electrode was tested in real samples with the good accuracy and satisfying recovery. (C) 2019 The Electrochemical Society.

Electrical, enzymatic graphene biosensing of 5-aminosalicylic acid.

Development of glucose biosensors based on nanostructured graphene-conducting polyaniline composite.

Fabrication of iron tin oxide/tin oxide intertwined graphitic carbon nitride hybrid composite electrocatalyst for electrochemical detection of 5-aminosalicylic acid in human urine and pharmaceutical tablet samples

Graphene-Based Flexible Sensors for Simultaneous Detection of Ascorbic Acid, Dopamine, and Uric Acid

Facile Assembly of Graphene on Anion Exchange Resin Microspheres for Electrochemical Sensing and Biosensing.

Bio-agent free electrochemical detection of Salicylic acid

Performance Enhancement of SPR Biosensor Using Graphene–MoS2 Hybrid Structure

An Electrochemical Immunosensor Based on SPA and rGO-PEI-Ag-Nf for the Detection of Arsanilic Acid

Electrochemical ascorbic acid sensor based on DMF-exfoliated graphene

Graphene quantum dots mediated acrylamide biosensing

Computationally Optimized Graphene-Based Electrochemical Sensor with Enhanced Signal Stability for the Determination of the Antimicrobial Agent 9-aminoacridine

Self-Reduction of Bimetallic Nanoparticles on Flexible Mxene-Graphene Electrodes for Simultaneous Detection of Ascorbic Acid, Dopamine, and Uric Acid

A Hydrothermal Synthesis of Graphene Quantum Dots Modified Carbon Paste Electrode as an Efficient Electro Sensor Towards L-Ascorbic Acid

Fabrication of a salivary amylase electrochemical sensor based on surface confined MWCNTs/β-cyclodextrin/starch architect for dental caries in clinical samples

A Portable Microelectrochemical Sensor Based on Potentiostatic Polarization-Treated and Laser-Induced Graphene for the Simultaneous Determination of Ascorbic Acid, Dopamine, and Uric Acid

3D Graphene Foams Decorated by CuO Nanoflowers for Ultrasensitive Ascorbic Acid Detection.

Facile Electrochemical Biosensing Platform Based on Laser Induced Graphene/Laccase Electrode for the Effective Determination of Gallic Acid

Graphene Oxide/Multiwalled Carbon Nanotubes Composites As an Enhanced Sensing Platform for Voltammetric Determination of Salicylic Acid

Electrochemical sensor based on nitrogen doped graphene: simultaneous determination of ascorbic acid, dopamine and uric acid.

Electrochemical Sensing Platform Based on Three-Dimensional Holey Graphene for Highly Selective and Ultra-Sensitive Detection of Ascorbic Acid, Uric Acid, and Nitrite