Change of pH indicator's pKa value via molecular imprinting.

Chengdu Liang,Michael J Weaver,Sheng Dai

DOI: https://doi.org/10.1039/B203496D

2002-01-01

Abstract:The pKa value of the indicator is significantly changed up to several orders of magnitude by the imprinting synthesis; this fine-tuning of the reactivity for pH indicators via the imprinting synthesis may find novel applications in fabricating pH sensors with tailored pKa values.

What problem does this paper attempt to address?

Change of Ph Indicator’s Pka Value Via Molecular Imprintingelectronic Supplementary Information (ESI) Available: Adsorption Isotherms, Schematic of Experimental Setup, FTIR Spectra of Doped Sol–gel Glasses, SAXS Curves, UV–vis Spectra of TD-MR and Its Protonated Form, Structure of TD-MR, Comparison of Template Environments, SEM Images and Photograph of Imprinted and Nonimprinted Sol–gel Glasses. See Http://Www.rsc.org/suppdata/cc/b2/b203496d/

CD Liang,MJ Weaver,S Dai

DOI: https://doi.org/10.1039/b203496d

IF: 4.9

2002-01-01

Chemical Communications

Abstract:The pK(a) value of the indicator is significantly changed up to several orders of magnitude by the imprinting synthesis; this fine-tuning of the reactivity for pH indicators via the imprinting synthesis may find novel applications in fabricating pH sensors with tailored pK(a) values.
Progress in Fluorescent Molecular Imprinting Polymer Sensors

Huiyun Wang,Yunling Gao,Kejian Yao

DOI: https://doi.org/10.14159/j.cnki.0441-3776.2010.05.017

2010-01-01

Abstract:Molecular imprinting technique is a borderline subject which combines the advantages of the subjects of high polymer chemistry, analytical chemistry and science of material. Molecular imprinting technique is a novel technique based on mimicking specification of antibody-antigen. The study of fluorescent molecular imprinting polymer sensors is a significant direction in the development of current sensors with a bright prospect. Fluorescent molecular imprinting polymer sensors combine the recognition ability and predetermined selectivity of molecular imprinting polymers with the high sensitivity of fluorescence analysis. This review summarizes the progress of fluorescent molecular imprinting polymer sensors in recent years. The mechanism of preparation, methods for monitoring binding sites and applications on organic small molecules and ions of fluorescent molecular imprinting polymer sensors are described in detail. Additionally, the development trend of fluorescent molecular imprinting polymer sensors is also discussed.
Molecular imprinting in chemical sensors and sensor arrays

Xinghui XU,Yunling GAO,Kejian YAO

DOI: https://doi.org/10.3969/j.issn.1000-6613.2013.12.019

2013-01-01

Abstract:Molecularly imprinted polymers (MIPs),as one of the most attractive research topics,offer unique advantages,such as high selectivity,predefined recognition properties,ease of preparation, low-cost production. The recent developments in the field of MIPs-based chemical sensors and sensor arrays are reviewed. The individual sensors with high selectivity,including electrochemical sensors, photochemical sensors and quality sensitive sensors are presented. Sensor arrays based on cross-reactivity of MIPs show limited application. Specifically,photochemical sensor arrays are discussed. The future development of MIPs-based sensors and sensor arrays would be guided by the understanding of imprinting process. MIPs-based sensors and sensor arrays chould show potential application in various fields,such as food analysis,drug control and environmental monitoring.
Molecular imprinting polymer coated BAW bio-mimic sensor for direct determination of epinephrine

Chengdu Liang,Hui Peng,Anhong Zhou,Lihua Nie,Shouzhuo Yao

DOI: https://doi.org/10.1016/S0003-2670(00)00845-X

IF: 6.911

2000-01-01

Analytica Chimica Acta

Abstract:A bio-mimic bulk acoustic wave (BAW) sensor was fabricated by coating it with the epinephrine template molecular imprinting polymer (MIP). This sensor exhibited high selectivity and sensitive response to epinephrine. A linear relationship between 5.0×10−8 and 2.0×10−5M was revealed. The detection limit was 2.0×10−8M. Recoveries were 93.2–108.7%. Influencing factors were investigated in detail and optimized. Analytical applications of this bio-mimic sensor were performed.
Study of a molecular imprinting polymer coated BAW bio-mimic sensor and its application to the determination of caffeine in human serum and urine.

C Liang,H Peng,X Bao,L Nie,S Yao

DOI: https://doi.org/10.1039/a905112k

1999-01-01

Abstract:A bio-mimic bulk acoustic wave (BAW) sensor was fabricated by coating the caffeine (CAF) template molecular imprinting polymer (MIP). This sensor exhibited high selectivity and a sensitive mass response to CAF. The response range of the sensor was between 5.0 x 10(-9) and 1.0 x 10(-4) M with a detection limit of 5.0 x 10(-9) M at pH 8.0. Recoveries were 96.1-105.6%. Influencing factors were investigated in detail and optimized. When employed to detect real samples, the proposed method proved to be a convenient method with the advantages of high sensitivity, good selectivity and ease of handling.
On-line monitoring of the dopamine-based molecular imprinting processes for protein templates with the assistance of a fluorescent indicator

Yibin Liu,Huaisyuan Xie,Xinyi Li,Ying Sun,Zhiwei Zhu,Meiping Zhao

DOI: https://doi.org/10.1007/s00604-022-05221-9

IF: 5.7

2022-03-09

Microchimica Acta

Abstract:On-line monitoring of the dopamine (DA)-based molecular imprinting processes over Fe3O4@SiO2-NH2 nanoparticles (SiMNPs) is reported by using a real-time quantitative PCR machine. Taking advantages of the efficient fluorescence quenching capability of polydopamine (PDA) and its high binding affinity to rhodamine B (RhB), we performed molecular imprinting against different proteins with free dopamine as the functional monomer and RhB as a fluorescent indicator. Along with the template molecules, the fluorescent indicators were continuously encapsulated into the PDA layer formed on the surface of the SiMNPs, resulting in immediate quenching of the fluorescence, which can be conveniently monitored in real time. As proteins showed sequence-dependent influences on the oxidation of dopamine and subsequent self-assembly on the surface of the SiMNPs, the observed fluorescence signals clearly indicated the polymerization progress in the presence of the template proteins, allowing precise control of the reaction time for different templates at a given initial concentration. The optimum end point of the reaction was found to be when 90 ± 3% of the templates had been encapsulated into the polymer, which offered the highest imprinting factor and selectivity. We applied the approach to prepare a primary PDA-based surface imprinted polymer for a multifunctional protein apurinic/apyrimidinic endonuclease/redox effector factor 1 (APE1). After further introduction of 3-hydroxyphenylboronic acid to the interfaces between APE1 and PDA, the resultant molecularly imprinted polymers (MIP-II) enabled quantitative isolation APE1 from cell lysate samples. The developed approach will be useful for the quantitative preparation of PDA-based MIPs for precious template proteins with limited input quantity. It is also applicable for further study on the effects of different proteins or peptides on the PDA formation reactions.

chemistry, analytical
Surface Molecular Imprinting on Hybrid SiO2-coated CdTe Nanocrystals for Selective Optosensing of Bisphenol A and Its Optimal Design

Chunxiao Qiu,Youhong Xing,Wenming Yang,Zhiping Zhou,Yingchun Wang,Hong Liu,Wanzhen Xu

DOI: https://doi.org/10.1016/j.apsusc.2015.03.150

IF: 6.7

2015-01-01

Applied Surface Science

Abstract:Twenty molecular dynamics (MD) simulations of molecular imprinting prepolymerization systems had been performed to optimize the imprinting shell of the fluorescent sensor. The results revealed that the system with a Bisphenol A (BPA): 3-aminopropyltriethoxysilane (APTES): tetraethylorthosilicate (TEOS) mole ratio of 10:15:60 had the most stable template (T)-functional monomer (FM) cluster. Correspondingly, five kinds of imprinted and non-imprinted polymers were synthesized to assess the reliability and validity of the simulation results. Hybrid SiO2-coated CdTe NCs (HS-QD) were synthesized by a simple reflux procedure including a sol-gel reaction that resulted in the formation of a hybrid SiO2 layer with CdS-like clusters on a CdTe core. Based on the optimal component ratio of the prepolymerization system, MIP shells were anchored on the surface of HS-QD to build a fluorescent MIP sensor. A linear relationship between relative fluorescence intensity and the concentration of BPA had been obtained covering the concentration range of 0.05-10 mu mol L-1 with a limit of detection of 6 nmol L-1. The feasibility of the fluorescent sensor was successfully evaluated through the analysis of BPA in river water and milk. The recoveries are above 96.31%, and the relative standard deviation (RSD) ranged from 1.55% to 2.78%. (C) 2015 Elsevier B.V. All rights reserved.
Recent developments in the molecular imprinting of proteins

David E. Hansen

DOI: https://doi.org/10.1016/j.biomaterials.2007.06.017

IF: 14

2007-10-01

Biomaterials

Abstract:Molecular imprinting is an inexpensive method for the rapid fabrication of organic polymeric and inorganic network-structured materials that selectively bind a template molecule--in other words, materials that function as artificial antibodies. Imprints against small-molecule templates have been generated for decades, but attempts to prepare imprints against proteins have, until recently, been far less successful. The field has progressed rapidly, however, and a number of molecular imprints selective for protein ligands have now been reported. Given the enormous potential of replacing the antibodies used in a host of immunoassays with robust and inexpensive receptors, efforts in this area continue to intensify. This review begins with a brief analysis of two naturally occurring protein-ligand complexes, each of which illustrates the specific interactions essential for precise molecular recognition. Key developments--all appearing in 2006 and 2007--in the molecular imprinting of proteins, including many impressive advances, are then discussed.

engineering, biomedical,materials science, biomaterials
A molecular imprinting photoelectrochemical sensor modified by polymer brushes and its detection for BSA

Xin Li,Bing Li,Jie Huang,Haiyan Zhu,Ying Li,Gang Shi

DOI: https://doi.org/10.1016/j.cej.2024.149297

IF: 15.1

2024-02-09

Chemical Engineering Journal

Abstract:Polydopamine (PDA)-based molecular imprinting photoelectrochemical (MIP-PEC) sensor is usually applied to recognize proteins. However, the abundant active functional groups on the PDA surface lead to a non-specific adsorption at the non-imprinted sites, resulting in a decrease in the ability of the MIP-PEC sensor to qualitatively analyze proteins. To solve this problem, in the present work, the polymer brush is specially designed to been grafted onto the PDA imprinted layer of the Si-based photoelectrode and then reduces the probability of non-specific adsorption, improving the specific detection ability. In addition, the Si-based photoelectrode was formed by successively modifying buried junction, nitrogen-doped carbon and TiO 2 on the Si wafer with micropyramid structure, enhancing the photocurrent density of the photoelectrode and improving the detection sensitivity. The experimental results suggest that the specific recognition ability of the MIP-PEC sensor to BSA was significantly improved with an increase of imprinting factor from 5.10 to 7.06. Also, the sensing signals showed a good linearity with BSA concentration in a range of 10 -16 -10 -9 mg·mL −1 , and a limit of detection of 2.203 × 10 -17 mg·mL −1 (S/N = 3). Furthermore, it was also successful to analysis as the template of acetylcholine was used, confirming the universality of this method.

engineering, chemical, environmental
Introducing molecular imprinting onto nanozymes: toward selective catalytic analysis

Zhijian Bu,Lian Huang,Shu Li,Qingzhen Tian,Zheng Tang,Qiaoqiao Diao,Xinyu Chen,Jinjin Liu,Xiangheng Niu

DOI: https://doi.org/10.1007/s00216-024-05183-2

2024-02-05

Analytical and Bioanalytical Chemistry

Abstract:The discovery of enzyme-like catalytic characteristics in nanomaterials triggers the generation of nanozymes and their multifarious applications. As a class of artificial mimetic enzymes, nanozymes are widely recognized to have better stability and lower cost than natural bio-enzymes, but the lack of catalytic specificity hinders their wider use. To solve the problem, several potential strategies are explored, among which molecular imprinting attracts much attention because of its powerful capacity for creating specific binding cavities as biomimetic receptors. Attractively, introducing molecularly imprinted polymers (MIPs) onto nanozyme surfaces can make an impact on the latter's catalytic activity. As a result, in recent years, MIPs featuring universal fabrication, low cost, and good stability have been intensively integrated with nanozymes for biochemical detection. In this critical review, we first summarize the general fabrication of nanozyme@MIPs, followed by clarifying the potential effects of molecular imprinting on the catalytic performance of nanozymes in terms of selectivity and activity. Typical examples are emphatically discussed to highlight the latest progress of nanozyme@MIPs applied in catalytic analysis. In the end, personal viewpoints on the future directions of nanozyme@MIPs are presented, to provide a reference for studying the interactions between MIPs and nanozymes and attract more efforts to advance this promising area.

chemistry, analytical,biochemical research methods
Molecular imprinting technology for microorganism analysis

Mengfan Jia,Zhong Zhang,Jinhua Li,Xin Ma,Lingxin Chen,Xingbin Yang

DOI: https://doi.org/10.1016/j.trac.2018.07.011

IF: 14.908

2018-09-01

TrAC Trends in Analytical Chemistry

Abstract:Molecular imprinting technology has been widely applied to various fields, owing to unique features of structure predictability, recognition specificity and application universality. Microorganism imprinting has attracted significant interests attributing to the high selectivity, simplicity rapidity, and excellent stability as well as low cost and eco-friendliness. Herein, we purpose to review the recent advances of MIT for microorganism analysis, concerning imprinting methods, analytical detection methods and typical applications. Various imprinting methods including direct and indirect imprinting for microorganism-MIPs preparation are comprehensively summarized. MIPs based biosensors containing fluorescence, electrochemical, piezoelectric and surface plasmon resonance for analytical detection of microorganisms is highlighted. Representative applications of microbiological imprinting are discussed, involving detection and quantification of bacteria, identification of bacterial species, and determination of yeast growth status. Finally, we propose the remaining challenges and future perspectives to accelerate the development and utilization of MIT in microorganism analysis and thereby push forwards microorganism identification and determination.

chemistry, analytical
Enhancement anti-interference ability of photoelectrochemical sensor via differential molecularly imprinting technique demonstrated by dopamine determination

Qi Kang,Qiao Zhang,Lixin Zang,Mengru Zhao,Xiaolan Chen,Dazhong Shen

DOI: https://doi.org/10.1016/j.aca.2020.05.063

2020-08-15

Abstract:Molecularly imprinting polymers (MIPs), as artificial antibodies with high recognition selectivity to template molecules, are widely used in various biosensors. To improve further the selectivity of MIPs-based photoelectrochemical (PEC) biosensors, we report a differential strategy using non-imprinted polymers (NIPs) as the reference. In a proof-to-concept example for the determination of dopamine (DA), MIPs and NIPs membranes were fabricated by electrochemical polymerization of polypyrrole membranes on the surface of graphene quantum dots (GQDs)/TiO2 nanotubes (NTs). The photocurrent difference between the two PEC cells, MIPs@GQDs/TiO2 NTs-Pt and NIPs@GQDs/TiO2 NTs-Pt, was measured as the signal. As the non-specific adsorption of non-template molecules on the outside surface of MIPs and NIPs membranes is similar, the anti-interference ability for the determination of DA is much improved by using differential strategy. In the normal and differential PEC measurement models, 10.0 μM ascorbic acid is equivalent to 3.12 and 0.40 μM DA, respectively. Further, the smaller specific surface area in NIPs membrane was compensated by using a weight factor to correct the residual interference in a modified differential model. By using 10.0 μM ascorbic acid as the balance point, the presence of 10.0 μM H2O2, glutathione, uric acid or glucose is equivalent only to 0.090, 0.061,0.11 or 0.041 μM of DA, respectively, which are about 3-7% of their interference levels in the normal photocurrent model. The differential PEC method was applied in the determination of DA in serum samples in the linear range of 0.05-12.5 μM, with the detection limit of 0.018 μM.
Bioenzyme-induced molecularly imprinted polymers using optimal design of computational chemistry for enhanced specific electrochemical sensing of protocatechuic acid in medicines

Donglei Fu,Junjie Deng,Bowen Zhang,Cheng Chen,Caihong Lv,Houbin Li,Xinghai Liu

DOI: https://doi.org/10.1016/j.snb.2023.134153

2023-06-30

Abstract:The sensitive and selective determination of the active ingredient in medicines has become an inescapable challenge in the sensing field. With the concerns above, an electrochemical sensor has been designed based on theoretically optimized bioenzyme-induced molecularly imprinted polymers (MIPs) for the specific determination of protocatechuic acid (PA) for the first time. In detail, the LaFeO 3 nanosphere is employed as the carrier to support bovine hemoglobin (BHb) and biomimetic enzyme Au nanoparticles , which can decompose hydrogen peroxide to generate hydroxyl radicals. These hydroxyl radicals can initiate polymerization to afford the optimized MIPs. More importantly, density functional theory based on computational chemistry is utilized to deduce the optimal functional monomer, resulting in the best recognition effect. Subsequently, the pre-fabricated electrochemical sensor based on LaFeO 3 @ could achieve the specific determination of PA with a wide linear detection range of 0.2 μM to 1000 μM and the limit of detection of 55 nM. Meanwhile, the specific recognition of PA in traditional Chinese medicines such as hibiscus has been also accomplished with satisfactory recoveries, foreboding that the LaFeO 3 @ is indeed a suitable candidate for monitoring medication safety.

chemistry, analytical,electrochemistry,instruments & instrumentation
Novel Superparamagnetic Core-Shell Molecular Imprinting Microspheres Towards High Selective Sensing.

Guiying Jin,Wei Li,Shaoning Yu,Youyuan Peng,Jilie Kong

DOI: https://doi.org/10.1039/b802120a

2008-01-01

The Analyst

Abstract:Novel superparamagnetic core-shell imprinting microspheres (MCSIMs) were synthesized using magnetite microspheres with 350 nm diameter and 70 nm thickness silica gel to form core-shell Fe3O4/SiO2 composite for template phenylephrine (Phen) recognition and high efficiency separation. Compared to the previous imprinting recognition, the main advantage of this strategy lies in two aspects: one is the high stability and monodispersity of the MCSIMs structure, the other is the use of superparamagnetic Fe3O4/SiO2 microspheres as an immobilization matrix and separation tool, thus greatly simplifying time-consuming washing steps. The affinity and selectivity of the MCSIMs were monitored by QCM and electrochemistry measurements. Imprinting microspheres have a remarkable affinity to Phen over that of structurally related molecules, including DA, EP, Phe and Tyr. The relative binding selectivity for different analytes estimated from amperometric signals was Phen : DA : EP = 40 : 5 : 1. The MCSIMs sensor showed a high sensitivity (400 mu A mM(-1)), short response time (reaching 98% within 10 s), and broad linear response range from 1 mu M to 0.1 mM and low detection limit (0.1 mM). Additionally, the results of control experiments showed that only negligible signal was obtained for non-imprinting microspheres. This could be reasonably attributed to the unique surface pores, charges and especially the nature of the functional groups inside MCSIMs cavities.
Programmable hierarchical photonic crystal arrays activated by post-hydrolysis for highly sensitive biochemical pH sensing

Donghui Kou,Tan Shi,Lei Li,Shufen Zhang,Wei Ma

DOI: https://doi.org/10.1016/j.cej.2023.142176

IF: 15.1

2023-05-01

Chemical Engineering Journal

Abstract:Water is closely linked with our life and pH monitoring is of great significance to biochemistry, environment and industry. Herein, utilizing a controllable post-hydrolysis modification strategy, multilayered photonic crystal based pH sensors consist of mesoporous TiO2 and partially hydrolyzed poly(acrylamide-N,N’-methylene bis(acrylamide)) (P(AM-MBA)) layers are proposed. Varying pH from 4.0 to 8.5, the portable sensor transforms its color from violet to red with a linearly increased wavelength of 199 nm as the stopband generates ∼7 nm shift per 0.1 pH unit. The sensor exhibits repeatable response to pH change with a short sensing time of 0.8 s. Through goal-directed molecular regulations by the post-hydrolysis strategy, innovative dot-matrix sensor arrays with multiple sensing elements are created and present distinct color difference maps under diverse pH circumstances. And color based radar maps and PCA analysis greatly promote the detection accuracy and reliability. The dot-matrix sensors provide convenience for color-blind crowd and are applicable for use in human perspirations, suggesting promising potential in clinical applications. Furthermore, quartz crystal microbalance studies reveal the effect of the molecular regulation involving functional group and segment structure modifications on the sensing performance of the polymer based photonic materials, showcasing high reference values for future polymer-related researches.

engineering, chemical, environmental
Molecular imprinting of hemispherical pore-structured thin films via colloidal lithography for gaseous formaldehyde Gravimetric sensing

Jin Chul Yang,Suck Won Hong,Sangheon Jeon,Woon Ik Park,Myunghwan Byun,Jinyoung Park

DOI: https://doi.org/10.1016/j.apsusc.2021.151161

IF: 6.7

2021-12-01

Applied Surface Science

Abstract:In this study, formaldehyde (HCHO)-imprinted hemispherical pore-patterned thin films, consisting of poly(2-(trifluoromethyl)acrylic acid–co–ethylene glycol dimethacrylate–co–styrene) (poly(TFMAA–co–EGDMA–co–ST)), were fabricated using the design of molecularly imprinted polymers (MIPs) and a subsequent lithographic micro/nanoimprinting method to amplify HCHO sensing signals in quartz crystal microbalance (QCM) sensors. Its molecular imprinting condition was optimized by controlling the added amount of a ST monomer in a MIP precursor solution. From the resonant frequency change with respect to HCHO adsorption, the imprinting factor of the porous MIP film was calculated to have a value of 2.38 and the sensitivity (0.132 mg g−1 ppm−1) of the porous MIP film exhibited markedly improved characteristics with respect to the porous non-imprinted polymer (NIP) film (0.05 mg g−1 ppm−1). The selectivity of the MIP-QCM sensors for the detection of HCHO was examined in the presence of other analogous toxic gases such as hydrogen chloride and hydrogen fluoride. The HCHO-absorbed porous MIP film had higher selective features with selectivity coefficients (k* ≈ 3.83 (HCl) and 4.46 (HF)) than porous NIP films (k* ≈ 1.53 (HCl) and 2.20 (HF)). Moreover, the relative selectivity of the porous MIP film appeared to be 2.03–2.5, which was higher than those of the planar MIP film (1.70–1.73).

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Synthetic Mechanism of Molecular Imprinting at the Solid Phase

Todd Cowen,Enrico Stefanucci,Elena Piletska,Giovanna Marrazza,Francesco Canfarotta,Sergey A. Piletsky

DOI: https://doi.org/10.1021/acs.macromol.9b01913

IF: 5.5

2020-02-12

Macromolecules

Abstract:The standard mechanism of molecular imprinting centers on the formation of a monomer–template complex in the prepolymerization mixture which remains trapped in the polymeric network following polymerization in the presence of a cross-linker. The release of the template leaves behind a binding site with functional groups "frozen" in a conformation complementary to the structure of the template and its analogues. Herein, we discuss the limitations of this model and present an alternative, in which imprinting is a result of dynamic interactions among the template, monomers, oligomers, and growing polymers in a solution. As a model, we have chosen the solid-phase synthesis of molecularly imprinted polymer (MIP) nanoparticles. Evidence is provided from the surface plasmon resonance-based binding analysis of MIP and "protoparticles", literature sources, and theoretical considerations. We conclude that the alternative mechanism may explain some behavioral inconsistency of the conventional model, including the impact of temperature, cross-linking, and computational molecular models, and describe some possibilities for improvement in MIP affinity and selectivity.

polymer science
Rational design of molecularly imprinted photonic films assisted by chemometrics

Dan Xu,Wei Zhu,Yin Jiang,Xuesong Li,Weina Li,Jiecheng Cui,Jinxiang Yin,Guangtao Li

DOI: https://doi.org/10.1039/c2jm32833j

2012-01-01

Journal of Materials Chemistry

Abstract:Molecularly imprinted photonic polymer (photonic MIP) film can be prepared based on the combination of colloidal-crystal templating and molecular imprinting techniques. This kind of film is an ideal sensing material due to its distinct advantages such as high selectivity, rapid response and signal self-reporting. However, for the successful formation of this kind of sensing material, with high selectivity towards the imprinted molecules, a highly ordered and interconnected 3D macroporous structure, and a visually perceptible color change like pH-paper, each fabrication is strongly dependent on the determination of the main factors and an arduous process of preparation. In this work, the rational design of molecularly imprinted photonic film was realized by using response surface methodology (RSM) based on central composite design (CCD). Design of experiments following CCD allows selected factors to be changed systematically and simultaneously, thus reducing the number of experiments necessary. 20 photonic MIPs with different ratios of monomer : crosslinker : solvent were synthesized and their sensing properties were checked. Data were analyzed using analysis of variance (ANOVA). A second-order polynomial model was used for predicting the response. This model revealed that the crosslinker was dominant in the performance of photonic MIPs, and also allowed the optimum polymer composition to be predicted. Creatinine was used as the model analyte. Under the predicted optimum conditions, a sensor for the convenient detection of creatinine was fabricated with high sensitivity, quick response, and good stability. This also testifies to the fact that the RSM approach is appropriate to investigate the interactive effect of the selected factors and optimize polymerization recipes with a limited number of experiments. It is anticipated that this method opens a way to the efficient fabrication of photonic MIPs.
Molecular Imprinting Using a Functional Chain Transfer Agent

Phonlakrit Muang-Non,K Fremielle Lim,Anthony Katselas,Clovia I Holdsworth

DOI: https://doi.org/10.3390/molecules27041162

IF: 4.6

2022-02-09

Molecules

Abstract:This study demonstrates the feasibility of molecular imprinting using a functional chain transfer agent sans a functional monomer. Ethylene glycol dimethacrylate (EGDMA)-based MIPs were synthesised in the presence of thioglycolic acid (TGA) possessing a carboxylic acid group, capable of interacting with the chosen test template R,S-(±)-propranolol (PNL) and a labile S-H bond to facilitate an efficient chain transfer reaction. Quantitative 1H NMR measurements showed high PNL and TGA incorporation within the MIP, indicating an efficient chain transfer process and a favourable interaction between PNL and TGA. TGA-50, with the lowest amount of CTA, showed the largest imprinting effect and an imprinting factor (IF) of 2.1. The addition of MAA to the formulation improved the binding capacity of PNL to the MIP but also increased NIP binding, resulting in a slightly decreased IF of 1.5. The Kd for the high-affinity sites of the TGA/MAA MIP were found to be two times lower (10 ± 1 μM) than that for the high-affinity sites of the TGA-only MIPs, suggesting that the incorporation of the functional monomer MAA increases the affinity towards the PNL template. Selectivity studies, cross-reactivity as well as binary competitive and displacement assays showed the TGA-based MIPs to be highly selective towards PNL against pindolol and slightly competitive against atenolol. The morphologies of the polymers were shown to be affected by the concentration of the TGA, transforming into discrete macrospheres (from small aggregates) at a higher TGA concentration.
De Novo Construction of pKa‐Tunable Xanthene Molecules for pH Sensitive Fluorescence Navigation

Li‐Na Zhang,Shan‐Yong Chen,Lei Shi,Xiao‐Yun Ran,Hong Zhang,Huiyeon Moon,Yubin Lee,Xiao‐Qi Yu,Jong Seung Kim,Kun Li

DOI: https://doi.org/10.1002/adfm.202412595

IF: 19

2024-09-01

Advanced Functional Materials

Abstract:A novel strategy to develop multicolor and pKa‐tunable xanthene‐based probes with narrow acid‐base transition ranges is constructed by introducing electron‐rich pyridine as ingenious proton catcher, which is successful used for rapid and high‐contrast imaging of the distal metastatic tumor and fluorescence‐guided surgery. pH is spatiotemporal variable dynamically in physiological and pathological processes, and the tiny pH changes can result completely different physiological processes. However, the major drawbacks of conventional pH‐activatable probes are their large acid‐base transition width and the challenge to adjust their pKa suitable for various application. In response to these issues, a novel approach is proposed to realize sensitive response and a general strategy to construct a multicolor and pKa‐tunable xanthene‐based platform. In these probes, the narrowest acid‐base transition range is just 1 pH units, achieved by introducing the electron‐rich pyridine as ingenious proton catcher. Especially, Si‐4Py owns near‐infrared (NIR) signal and pKa of 5.56, which is successfully used for the rapid and high‐contrast imaging of distal metastatic tumors. This has significant implications for guiding surgeons in the removal of these tumors and ultimately improve patient outcomes. Additional, the sustainably innovative strategy proposed by this work can serve as effective reference in pH probe development.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology

Change of pH indicator's pKa value via molecular imprinting.

Progress in Fluorescent Molecular Imprinting Polymer Sensors

Molecular imprinting in chemical sensors and sensor arrays

Molecular imprinting polymer coated BAW bio-mimic sensor for direct determination of epinephrine

Study of a molecular imprinting polymer coated BAW bio-mimic sensor and its application to the determination of caffeine in human serum and urine.

On-line monitoring of the dopamine-based molecular imprinting processes for protein templates with the assistance of a fluorescent indicator

Surface Molecular Imprinting on Hybrid SiO2-coated CdTe Nanocrystals for Selective Optosensing of Bisphenol A and Its Optimal Design

Recent developments in the molecular imprinting of proteins

A molecular imprinting photoelectrochemical sensor modified by polymer brushes and its detection for BSA

Introducing molecular imprinting onto nanozymes: toward selective catalytic analysis

Molecular imprinting technology for microorganism analysis

Enhancement anti-interference ability of photoelectrochemical sensor via differential molecularly imprinting technique demonstrated by dopamine determination

Bioenzyme-induced molecularly imprinted polymers using optimal design of computational chemistry for enhanced specific electrochemical sensing of protocatechuic acid in medicines

Novel Superparamagnetic Core-Shell Molecular Imprinting Microspheres Towards High Selective Sensing.

Programmable hierarchical photonic crystal arrays activated by post-hydrolysis for highly sensitive biochemical pH sensing

Molecular imprinting of hemispherical pore-structured thin films via colloidal lithography for gaseous formaldehyde Gravimetric sensing

Synthetic Mechanism of Molecular Imprinting at the Solid Phase

Rational design of molecularly imprinted photonic films assisted by chemometrics

Molecular Imprinting Using a Functional Chain Transfer Agent

De Novo Construction of pKa‐Tunable Xanthene Molecules for pH Sensitive Fluorescence Navigation