Abstract:Abstract During the experiment, pressure-less silver sintering pastes that can sinter using a conventional reflow oven for die-attach applications were developed. This development makes it possible to produce die-attach assemblies in a continuous and high throughput fashion for mass production. Different reflow profiles such as “ramp-up and peak” and “ramp-up and plateau” types were tested and high shear strength joints with no voids were obtained. For each sample, the sintering time was around twelve minutes or less, which is about one order of the magnitude that is presently used for box oven sintering time. Two sintering pastes, A and B, were developed. Paste A has been used to study the relationship between processing conditions (reflow oven sintering temperature and atmosphere such as air vs nitrogen) and the die-attach structures (with varied substrate materials such as copper or active metal brazing (AMB) and surface metallization such as copper, silver, or gold). Under the same combined conditions of sintering temperature, atmosphere, and substrate type, the Ag metalized substrate gave the strongest joint shear strength. In comparison, Au metalized substrate displayed the weakest strength because of the formation of a “depletion layer” as a result of the diffusion of silver on gold surface, leaving behind a weak connection between sintered silver and Ag-Au layer. For the above noble metal metallized surfaces, sintering in air normally results in stronger joint shear strength than that in a nitrogen atmosphere. On the bare Cu metallized surface with nitrogen sintering, increasing the sintering temperature and changing to paste B are two ways to increase joint shear strength. Sintering on an AMB substrate displays around 10Mpa higher shear strength than that on a Cu substrate, indicating the importance of surface morphology. When sintering at 250°C in air, oxygen can help accelerate the inter-diffusion between Cu substrate and sintered Ag and enhance interfacial adhesion, increasing the shear strength. A higher sintering temperature reduces the adhesion due to the formation of large amounts of copper oxide; therefore, control of the optimum temperature range is key to obtaining a strong joint in air.

Performance of silver-glue attachment technology in assembly

Experimental studies on application of silver paste in thermosonic flip-chip bonding

Enhancing Semiconductor Package Reliability through Mechanical Property Optimization of Pressureless Sintering Die Attach Adhesives

Characterization of Low-Temperature Sintered Nanoscale Silver Paste for Attaching Semiconductor Devices

Avoidance of Bonding Pad Contamination Affecting Back-End Assembly Process

Double layered sintered silver die bonding technology with superior mechanical reliability

Emerging Lead-Free, High-Temperature Die-Attach Technology Enabled By Low-Temperature Sintering Of Nanoscale Silver Pastes

Application of Nano Silver Sintering Technique on the Chip Bonding for Flip-Chip and Vertical Light Emitting Diodes

Low Temperature Sintering of Silver Nanoparticle Paste for Electronic Packaging

“Drop-in” Conventional Reflow Oven Sinter-Able Pressure-Less Silver Paste for Die-Attach Assembly Mass Production

Low-Temperature Sintering of Nanoscale Silver Pastes for High-Performance and Highly-Reliable Device Interconnection

Rate-dependent Mechanical Properties of Cured Conductive Adhesives and Drop Impact Behavior of Adhesive Bonding Points in Electronic Interconnection

Thermomechanical Reliability of Low-Temperature Sintered Silver Die-Attachment

SiC Chip Attachment Sintered by Nanosilver Paste and Their Shear Strength Evaluation

Bonding Process of Copper Foam-Silver Composite and Performance Characterization of the Joint

Mechanical and Microstructural Analysis of an Ultra-Flexible Nano-Silver Paste Sintered Joint

A Multilayer Paste Based on Ag Nanoparticles with Cu@Sn for Die Attachment in Power Device Packaging

Performance of Component Interconnection Methods on Direct Write Additive Silver Circuits

Microstructural and Mechanical Evolution of Silver Sintering Die Attach for SiC Power Devices During High Temperature Applications

Large-area Die Attachment and the Surface Finish Effect on Bonding Strength of Joints in High-power Electronics Using a Low-temperature Sinterable Cu Nanoparticle Paste

Joint Analysis and Reliability Test of Epoxy-Based Nano Silver Paste Under Different Pressure-Less Sintering Processes