Abstract:Permanent Magnet-Assisted Synchronous Reluctance Machines (PMASynRM) provide a low-cost alternative to Surface PM Machines due to the use of relatively lower grades of rare-earth (RE) or RE-free magnets, as the performance degradation due to weaker magnets is compensated by the presence of reluctance torque. However, the weaker magnets suffer from a high risk of demagnetization, leading to unreliable motor operation. Using a blend of RE and RE-free magnets has the potential to overcome this issue. This paper proposes to blend different grades of various rare-earth (RE) and rare-earth-free (RE-free) magnets in six different combinations and utilizes them in two-layer and three-layer U-shaped PMASynRM topologies with both eight-pole and six-pole variations. The rotor of the various designs is then optimized using a differential evolution (DE) based optimization algorithm to obtain low-cost designs with reduced RE magnet volume and minimum demagnetization risk. The optimization of each design is also integrated with the evaluation of mechanical stresses in the rotor laminations so as to maintain the stresses below the material yield strength. Furthermore, the various performance metrics, such as toque–speed/power–speed characteristics, demagnetization, and efficiency maps, are evaluated for each of the optimized and mechanically feasible designs. A quantitative comparison of the various optimized designs is also obtained to highlight the various trade-offs. The results indicate the feasibility of meeting the baseline torque requirement across the entire speed range, even with a 100% reduction in RE magnet volume and less than 5% demagnetization risk, while achieving a cost reduction exceeding 50%. Moreover, the two-layer, eight-pole designs exhibit relatively higher performance, whereas the three-layer, eight-pole designs are found to be the most economical option.

Optimization of added permanent magnet amount in synchronous reluctance machines for high performance

Influence of Design Parameters on Output Torque of Novel Doubly-Fed Flux-Switching Permanent Magnet Machines

Comparison of Dual-Stator Permanent Magnet Machines with Different Rotor Topologies

Optimum parameters and maximum torque performances of the synchronous reluctance machine

Optimum Parameters And Maximum Torque Performances Of The Pm-Assisted Synchronous Reluctance Machine

Design and analysis of high power density permanent magnet-assisted synchronous reluctance motor

A Hybrid PM-Assisted SynRM with Ferrite and Rare-Earth Magnets

Electromagnetic Design Optimization Integrated with Mechanical Stress Analysis of PM-Assisted Synchronous Reluctance Machine Topologies Enabled with a Blend of Magnets

Analysis and Design of Synchronous Reluctance Machines Part Ⅻ: Investigation of Permanent Magnet Assisted Synchronous Reluctance Machines

Optimized Design of High Torque Density Permanent Magnet Synchronous Motor with Halbach Magnet

Study on Effect of Permanent Magnet Remanence on High Speed Permanent Magnet Assisted Synchronous Reluctance Machines

Comparative Study on Synchronous Reluctance and PM Machines

Torque Ripple Reduction of a Salient-Pole Permanent Magnet Synchronous Machine with an Advanced Step-Skewed Rotor Design.

Design Optimization with Outer Rotor Interior Permanent Magnet Synchronous Motor with Hybird Permanent Magnet

ANALYSIS OF THE RELATION BETWEEN THE ELECTRO-MAGNETIC PARAMETERS AND THE STRUCTURE OF SYNCHRONOUS RELUCTANCE PERMANENT MAGNETIC MOTORS

Comparative Study Between Doubly Salient PM Machine with New Stator/Rotor-Pole Number Combination and Biased Flux PM Machine

Comparative Analysis of Doubly Fed Flux-Reversal Permanent Magnet Machines with Different PM Arrangements and Consequent-Pole Topologies

Analysis and Optimization of Permanent Magnet-Assisted Synchronous Reluctance Machine Based on Neural Network Fitting

Flux Weakening Control Of Interior Permanent Magnet Synchronous Machine To Improve Torque Performance

Permanent Magnet Synchronous Reluctance Machines with Axially Combined Rotor Structure

Design and Analysis of Permanent Magnet Assisted Switched Reluctance Motor Considering Iron Core Saturation