Abstract:To bring the potential power of the capacitively coupled contactless conductivity detection ((CD)-D-4) technique to full play and extend the application fields of (CD)-D-4, our previous work has developed a (CD)-D-4 sensor which is suitable for conductivity detection of electrolyte solution in industrial fields (Sensors and Actuators A 213 (2014) 1-8). With the introduction of series resonance principle, the (CD)-D-4 sensor can overcome the influence of coupling capacitances on conductivity measurement. By a specific design of shield configuration, the (CD)-D-4 sensor can overcome the influence of stray capacitances and the environment interference in industrial fields. Although the measurement performance of the (CD)-D-4 sensor is satisfactory and it is suitable for the conductivity detection in industrial fields, the input-output characteristic of the (CD)-D-4 sensor is non-monotonic, which may limit the practical applications of the (CD)-D-4 sensor. To overcome this drawback, an improved (CD)-D-4 sensor for conductivity detection in industrial fields has been developed. The basic conductivity measurement method (the series resonance principle) and the shield configuration of the improved (CD)-D-4 sensor are the same as those of the (CD)-D-4 sensor in our previous work. However, the measurement circuit of the detection path of the improved (CD)-D-4 sensor has been optimized. The one-inductor design has been replaced by a two-inductor design. With this optimization, the input-output characteristic of the improved (CD)-D-4 sensor is theoretically monotonic. Conductivity measurement experiments were carried out on four pipes with inner diameters of 1.8 mm, 3.3 mm, 5.0 mm and 7.6 mm, respectively. The experimental results indicate that the development of the improved (CD)-D-4 sensor is successful. In comparison with the previous (CD)-D-4 sensor, the measurement accuracy of the improved (CD)-D-4 sensor is comparable. But, the improved (CD)-D-4 sensor has the advantages of the monotonic input-output characteristic and the convenience for practical conductivity detection in industrial fields. Meanwhile, it is found that the input-output characteristic of the improved (CD)-D-4 sensor is nonlinear and the sensitivity of the improved (CD)-D-4 sensor decreases with the increase of conductivity. (C) 2015 Elsevier B.V. All rights reserved.

A new on-line insulation diagnostic method for capacitive-type equipment

Online Measurement of Conductivity/permittivity of Fluid by a New Contactless Impedance Sensor.

Icing Thickness Measuring Method with a Capacitance Sensor for Overhead Power Transmission Lines

New Diagnosis Method for Space Charge-dependent Interfacial Electrical Tree in Packaging Insulation Using Current Integrated Charge Measurement

Additional Low Frequency Signal Measurement Method Of Insulation Resistance About Mine Cable

An Improved Capacitively Coupled Contactless Conductivity Detection Sensor for Industrial Applications

Study on On-Line Monitoring of Dielectric Loss Factor for Insulation on Synthetical Relative Idea

Methodology For Increasing Accuracy Of On-Line Insulation Diagnosis

An Online Groundwall and Phase-to-Phase Stator Insulation Monitoring Method for Inverter-Fed Machine.

Measuring the Dissipation Factor of Capacitive Equipment Under Damped AC Voltage

A Noninvasive Interturn Insulation Condition Monitoring Method Based on the Common-Mode Impedance Spectrum of Inverter-Fed Machines

Online Monitoring of Capacitance and Dissipation Factor of Motor Stator Winding Insulation During Accelerated Life Testing

Development of on-line monitoring system for insulation of high voltage electrical equipment

Online Condition Monitoring of Line-end Coils Insulation for Inverter-fed Machine by Switching Oscillation Mode Decomposition

An Improved Online Stator Insulation Monitoring Method Based on Common-Mode Impedance Spectrum Considering the Effect of Aging Position

Online Monitoring for Underground Power Cable Insulation Based on Resonance Frequency Analysis under Chirp Signal Injection

Online Condition Monitoring of Line-End Coil Insulation for Inverter-Fed Machine by Switching Oscillation Mode Decomposition

Comparative Study of Neutral-Voltage-Based and Leakage-Current-Based Online Condition Monitoring Methods for Stator Insulation of Inverter-Fed Machines

An Improved Power Cable Insulation Monitoring Method for Inverter-fed Machines Using Switching Oscillation Damping Feature

Sensor Monitoring and Online Measurement Correction in Electric Capacitance Tomography System

Design of capacitive electrostatic probes for online measurement of surface charge on ±320 kV tri‐post insulators