Abstract:The study of impedance matching between a transducer and its working medium is an important part of acoustic transducer design. The traditional quarter wavelength matching (Q-matching) scheme is not suitable for broadband capacitive micromachined ultrasonic transducers. To mitigate this issue, a 0–3 composite broadband matching layer based on polydimethylsiloxane (PDMS) substrate/TiO2 particles is designed to achieve electrical insulation and efficient acoustic energy transfer of underwater capacitive micromachined ultrasonic transducer (CMUT) devices. In this work, the coherent potential approximation model is used to analyze the properties of 0–3 composite materials. Samples are prepared for performance testing to determine the proportion of TiO2 particles that enable the 0–3 composite materials to have the same longitudinal acoustic impedance as water. The CMUT device is packaged by a spin coating and pouring process, and its performance tests are carried out. The experimental results show that the central frequency of the transducer remains at 1.74 MHz, the −6 dB fractional bandwidth increases from 97.3% to 100.3%, the 3 dB directional main beam width increases from 8.3°to 10.3°, the side lobes decrease significantly, and the device has good reception sensitivity. These values imply that the 0–3 composite material has good matching performance, and this matching scheme has the advantages of high efficiency and wide bandwidth. This broadband matching method endows CMUTs with great advantages in underwater detection systems, and it facilitates underwater ultrasonic imaging of CMUT.

Characterization of Ultra-Thin Quarter-Wavelength Matching Layers of High Frequency Ultrasonic Transducers

Tunable high acoustic impedance alumina epoxy composite matching for high frequency ultrasound transducer

Simultaneous Thickness, Velocity, Density, and Attenuation Measurement of a Thin Layer by Time-Resolved Acoustic Microscopy

Simultaneous Measurement of Elastic Moduli, Attenuation, Density, and Thickness of a Layer by Ultrasonic Spectroscopy Using Point-Focus Transducer

Simultaneously Measuring Thickness, Density, Velocity and Attenuation of Thin Layers Using V(z,t) Data from Time-Resolved Acoustic Microscopy.

Surface Wave Transducer for Ultrasonic Nondestructive Testing of Polymer Components

Anodic Aluminum Oxide-Epoxy Composite Acoustic Matching Layers for Ultrasonic Transducer Application.

Simultaneous Measurement of Local Longitudinal and Transverse Wave Velocities, Attenuation, Density, and Thickness of Films by Using Point-Focus Ultrasonic Spectroscopy

A Novel Technique for the Measurement of the Acoustic Properties of a Thin Linear-Viscoelastic Layer Using a Planar Ultrasonic Transducer

The study of matching layers for high-end ultrasonic transducers

Broadband Gradient Impedance Matching Using an Acoustic Metamaterial for Ultrasonic Transducers

Towards Experimental Perfectly-Matched Layers With Ultra-Thin Metamaterial Surfaces

Research and Fabrication of High-Frequency Broadband and Omnidirectional Transmitting Transducer

Micromechanical Piezoelectric Micromachined Ultrasonic Transducer array package enhancement with integrated frontliners

Fabrication and Modeling of Matching System for Air-Coupled Transducer

Optimized Backing Layers Design for High Frequency Broad Bandwidth Ultrasonic Transducer

Optimized Design of High-Temperature Resistant Air-Coupled Ultrasonic Transducer (ACUT) Based on Single Acoustic Matching Layer

Development of interdigital transducer sensors for non-destructive characterization of thin films using high frequency Rayleigh waves

Novel multi-layer-composites design for ultrasonic transducer applications

Simulation of Layer Thickness Measurement in Thin Multi-Layered Material by Variable-Focus Laser Ultrasonic Testing

Research on Broadband Matching Method for Capacitive Micromachined Ultrasonic Transducers Based on PDMS/TiO2 Particles