Abstract:We describe the modeling of magnetoelectric (ME) effect in the plate-type Terfenol-D/PZT laminate composite by introducing a newly proposed interface coupling factor into the equivalent circuit model, aiming at providing a guidance for designing, fabricating and using the ME laminate composite based devices, such as current sensor, magnetic sensor, energy harvester, and wireless energy transfer system. Considering that the strains of the magnetostrictive and piezoelectric layers are not equal in actual operation due to the epoxy resin adhesive bonding condition, the equivalent circuit models of magnetostrictive and piezoelectric layers are created based on the constitutive equation and the equation of motion, respectively. An interface coupling factor k(c) is introduced which physically reflects the strain transfer condition between the magnetostrictive and piezoelectric phases. Specifically, the respective equivalent circuit models of magnetostrictive and piezoelectric layers are combined with an ideal transformer whose turn-ratio is just the interface coupling factor. Furthermore, the theoretical expressions containing k(c) for the longitudinal ME voltage coefficient alpha(v) and the optimum thickness ratio n(optim) to which the maximum ME voltage coefficient corresponds are derived from the modified equivalent circuit model of ME laminate, where the interface coupling factor acts as an ideal transformer. To explore the influence of mechanical load on the interface coupling factor k(c), two sets of weights, i.e., 100 g and 500 g, are placed on the top of the ME laminates, each with the same thickness ratio n in the sample fabrication for comparison. A total of 12 L-T mode plate-type ME laminate samples with different-thickness configurations are fabricated. The interface coupling factors determined from the measured alpha(v) and the DC bias magnetic field H-bias are 0.15 for 500 g pre-mechanical load and 0.10 for 100 g pre-mechanical load, respectively. Furthermore, the measured optimum thickness ratios are 0.57 for k(c) = 0 : 1 5 and 0.50 for k(c) = 0 : 1 0, respectively. Both the measured ME voltage coefficient alpha(v) and optimum thickness ratio containing k(c) agree well with the corresponding theoretical predictions. The relationship between the optimum thickness ratios under two different mechanical loads remains unchanged, i.e., the measured optimum thickness ratio for k(c) = 0 : 1 5 is larger than for k(c) = 0.10. The experimental results verify the reasonability and correctness of the introduction of k(c) in the modified equivalent circuit model. The possible reasons for different interface coupling factors under different loads are also qualitatively discussed in this paper.

Equivalent Circuit for Unloaded Triple-Layer Piezoelectric Cantilevers

Admittance matrix of a symmetrical triple-layer piezoelectric cantilever

Equivalent Circuit Method for Resonant Analysis of Multilayer Piezoelectric-Magnetostrictive Composite Cantilever Structures

Theoretical Analysis of Dynamic Property for Piezoelectric Cantilever Triple-Layer Benders with Large Piezoelectric and Electromechanical Coupling Coefficients

Equivalent circuit with complex physical constants and equivalent-parameters-expressed dissipation factors of piezoelectric materials

A 2D equivalent circuit of piezoelectric ceramic ring for transducer design

Equivalent circuit of piezoelectric resonant disk gyroscope through admittance circle method

Modeling the Piezoelectric Cantilever Resonator with Different Width Layers

Equivalent circuit and optimum design of a multilayer laminated piezoelectric transformer

Research on Effective Electric-Mechanical Coupling Coefficient of Sandwich Type Piezoelectric Ultrasonic Transducer Using Bending Vibration Mode

Analysis of Functionally Graded and Laminated Piezoelectric Cantilever Actuators Subjected to Constant Voltage

Equivalent circuit model for plate type magnetoelectric laminate composite considering an interface coupling factor

Three-dimensional Electromechanical Responses of a Parallel Piezoelectric Bimorph

Nonlinear Equivalent Circuit of High-Power Sandwich Piezoelectric Ultrasonic Transducer

Theoretical modeling of a circular piezoelectric actuator for micro-systems

Establishment Of Actuation Model Of The Three-Layer Structure Piezoelectric Bimorph And Simulation Analysis Based On Analysis Of The Internal Energy

Electro-mechanical analysis of piezoelectric sandwich structure

THREE DIMENSIONAL EXACT ANALYSIS FOR FREE VIBRATION OF SIMPLY SUPPORTED PIEZOELECTRIC COMPOSITE LAMINATES 1)

An Analytical Model for Electrode–ceramic Interaction in Multilayer Piezoelectric Actuators

Electromechanical Analysis of a Piezoelectric Semiconductor Bilayer System with Imperfect Interface

Equivalent Circuit Model of Low-Frequency Magnetoelectric Effect in Disk-Type Terfenol-D/PZT Laminate Composites Considering a New Interface Coupling Factor