Abstract:INTRODUCTION: sensor setting. A Matlab (Mathworks Inc., MA) code was run to register The plantar metatarsal sites (i.e., five metatarsal heads (MTHs) and the two images according to three non-collinear ink dots marked on the underlying protective fat pads) at the ball of the forefoot are exposed hallux. "MTH template" represents the registered images with minimal to substantial dynamic contact forces during gait. Variations in vertical errors induced due to discrepancy between the target MTH and actual and shear components, including their magnitude and temporal sensor locations as evaluated by Xj and Yj. characteristics, may lead to painful conditions in rheumatoid arthritis and elevated risks of tissue damage in neuropathic foot [1, 2], Despite the fact that these clinical symptoms are often found at the forefoot and localized to metatarsal sites, there is very little evidence of accurate three-dimensional measurement of plantar metatarsal loads. One of the major obstacles is that pressure-shear sensor technology is still far from miniaturization to the point where it could accurately relate force distribution data to specific anatomical sites (e.g., the 2nd MTH) [3]. Gross plantar force pattern, for example, can only be "mapped" onto a specific portion of the foot (e.g., medial, central, and lateral forefoot) [4]. Subtle variations within individual metatarsal site often cannot be Figure 2. Method to create "MTH template" for the 2 MTH targeting. specifically extracted. This study describes the construction of a novel The subject initiated gait from a stationary posture. The right foot was gait platform-type system, and a pilot study to obtain the vertical, positioned over the gait plate with ankle being slightly dorsiflexed to anterior-posterior (AP), and medical-lateral (ML) ground reaction force simulate a heel strike. Data collections began as subjects started to (GRF) components of the foot plantar surface at individual MTH during plantarfiex to late stance and subsequently push-off, further completing barefoot walking. a series of 5 to 6 steps to the end of the 7m walkway at self-sleeted speed. To take measures at the each MTH, the "MTH template" was displayed on a laptop screen to guide the subject with appropriate starting point (i.e., heel-strike position) by direct comparison with the real-time image frames from the FASTCAM system. METHODS: Force sensor design: A customized tactile force sensor that is capable of detecting the forces at three orthogonal directions was specifically designed based on strain-gauge techniques. It has a flat top sensing surface that measures a square contact area of 1.9 X 1.9 cm. Each of the three sensor channels was independently calibrated by using an Instron machine (Model 5848, Canton, MA). Mechanical cross-talk was minimal (less than 0.1%). Measurement errors are less than 2.2%, 3.5%, and 3.7% for direct forces in the vertical, AP and ML axes, respectively.

Wearable Gait Analysis System for Ambulatory Measurement of Kinematics and Kinetics

Wireless Multi-Axial Force Sensing Shoe for Gait Abnormalities Monitoring

Flexible, Wireless, Multifunctional Integrated Electronic System for Daily Wearable Gait Detection

Development of a Non-Contacting Muscular Activity Measurement System for Evaluating Knee Extensors Training in Real-Time

Lower Body Kinematics Monitoring in Running Using Fabric-Based Wearable Sensors and Deep Convolutional Neural Networks

Estimation of ground reaction forces and ankle moment with multiple, low-cost sensors

Performance Evaluation Of Lower Limb Ambulatory Measurement Using Reduced Inertial Measurement Units And 3r Gait Model

Validation of wearable inertial sensor-based gait analysis system for measurement of spatiotemporal parameters and lower extremity joint kinematics in sagittal plane

A gait stability evaluation method based on wearable acceleration sensors

Estimation of Spatial-Temporal Gait Parameters based on the Fusion of Inertial and Film-Pressure Signals

A Fully Wireless Wearable Motion Tracking System with 3D Human Model for Gait Analysis

Inertial Measurement Unit-Based Estimation of Foot Trajectory for Clinical Gait Analysis

SensAA—Design and Verification of a Cloud-Based Wearable Biomechanical Data Acquisition System

A Walking Monitoring Shoe System For Simultaneous Plantar-Force Measurement And Gait-Phase Detection

Algorithm for Gait Parameters Estimation Based on Heel-Mounted Inertial Sensors

Comparing the Ground Reaction Forces, Toe Clearances, and Stride Lengths of Young and Older Adults Using a Novel Shoe Sensor System

GaitTracker: 3D Skeletal Tracking for Gait Analysis Based on Inertial Measurement Units

A Novel Gait Platform for Simultaneous Measurement of Vertical and Shear Force at Local Metatarsal Site in Walking

Inertial Measuring System to Evaluate Gait Parameters and Dynamic Alignments for Lower-Limb Amputation Subjects

Continuous Analysis of Running Mechanics by Means of an Integrated INS/GPS Device

The Development of the "Lab-in-shoe" System Based on an Instrumented Footwear for High-Throughput Analysis of Gait Parameters