Plasmon Enhanced Dye-Sensitized Solar Cells Using Nanoparticles of Different Geometries and Materials

Qi Xu,Fang Liu,Yidong Huang

2014-01-01

Abstract:Plasmonic dye sensitized solar cells with three sorts of nanoparticles are investigated. By utilizing nanoparticles of different geometries and metals, optical and electrical improvement is demonstrated whilst the efficiency is significantly boosted over 30%.

What problem does this paper attempt to address?

Efficiency Enhancement of Organic Solar Cells by Using Shape‐Dependent Broadband Plasmonic Absorption in Metallic Nanoparticles

xuanhua li,wallace c h choy,haifei lu,wei e i sha,a h p ho

DOI: https://doi.org/10.1002/adfm.201202476

IF: 19

2013-01-01

Advanced Functional Materials

Abstract:It is been widely reported that plasmonic effects in metallic nanomaterials can enhance light trapping in organix solar cells (OSCs). However, typical nanoparticles (NP) of high quality (i.e., mono-dispersive) only possess a single resonant absorption peak, which inevitably limits the power conversion efficiency (PCE) enhancement to a narrow spectral range. Broadband plasmonic absorption is obviously highly desirable. In this paper, a combination of Ag nanomaterials of different shapes, including nanoparticles and nanoprisms, is proposed for this purpose. The nanomaterials are synthesized using a simple wet chemical method. Theoretical and experimental studies show that the origin of the observed PCE enhancement is the simultaneous excitation of many plasmonic low- and high-order resonances modes, which are material-, shape-, size-, and polarization-dependent. Particularly for the Ag nanoprisms studied here, the high-order resonances result in higher contribution than low-order resonances to the absorption enhancement of OSCs through an improved overlap with the active material absorption spectrum. With the incorporation of the mixed nanomaterials into the active layer, a wide-band absorption improvement is demonstrated and the short-circuit photocurrent density (Jsc) improves by 17.91%. Finally, PCE is enhanced by 19.44% as compared to pre-optimized control OSCs. These results suggest a new approach to achieve higher overall enhancement through improving broadband absorption.
Influence of Geometry of Metallic Nanoparticles on Absorption of Thin-Film Organic Solar Cells: A Critical Examination.

Long Qian Cao,Zi He,Wei E. I. Sha,Ru-Shan Chen

DOI: https://doi.org/10.1109/access.2020.3014817

IF: 3.9

2020-01-01

IEEE Access

Abstract:Well-engineered light trapping designs will significantly improve power conversion efficiency of thin-film organic solar cells. Recently, metallic nanoparticles (NPs) have been widely used to concentrate sunlight in the active layer of OSCs. To critically examine the influence of geometry of metallic NPs on absorption of OSCs, the parallel finite-element method is applied to simulate the near-field multiple scattering effects in plasmonic NPs incorporated OSCs. The geometry-varied NPs including nano-cone, nano-inverted-cone, nano-cylinder, and nano-cuboid are systematically investigated. Furthermore, the absorption enhancement from the dielectric silicon NPs and perfectly reflecting NPs are also comprehensively offered. Compared to the off-plasmon resonance case, the absorption enhancement factor is higher for on-plasmon resonance case. However, the absorption of organic active material near plasmon resonance weakly contributes to exciton generation. Moreover, the height-dependent Fabry-Perot mode plays a key role in the light trapping off the plasmon resonance. Additionally, the tapered structure of the silver nano-cone, which leads to the best absorption enhancement of 3 at the wavelength of 680 nm, since it can reduce unwanted reflection loss and achieve broadband plasmonic resonance simultaneously.
Dual Plasmonic Nanostructures for High Performance Inverted Organic Solar Cells.

Xuanhua Li,Wallace C. H. Choy,Lijun Huo,Fengxian Xie,Wei E. I. Sha,Baofu Ding,Xia Guo,Yongfang Li,Jianhui Hou,Jingbi You,Yang

DOI: https://doi.org/10.1002/adma.201200120

IF: 29.4

2012-01-01

Advanced Materials

Abstract:Dual plasmonic metallic nanostructures in organic solar cells are demonstrated by simultaneously incorporating gold nanoparticles (NPs) into the active layer and fabricating the silver nanograting electrode by means of a vacuum-assisted nanoimprinting method. Apart from the waveguide modes and diffraction, hybridized surface plasmonic resonances (SPRs, from the Ag nanograting) and localized plasmonic resonances (LPRs, from the Au NPs) are simultaneously introduced to successfully achieve a high power conversion efficiency (PCE). Detailed facts of importance to specialist readers are published as "Supporting Information". Such documents are peer-reviewed, but not copy-edited or typeset. They are made available as submitted by the authors. Please note: The publisher is not responsible for the content or functionality of any supporting information supplied by the authors. Any queries (other than missing content) should be directed to the corresponding author for the article.
Plasmonic Nanoparticles Enhanced Dye-Sensitized Solar Cells

Qi Xu,Fang Liu,Weisi Meng,Yidong Huang

DOI: https://doi.org/10.1364/oe.20.00a898

2013-01-01

Abstract:We present an investigation on introducing core-shell Au@PVP nanoparticles (NPs) into dye-sensitized solar cells. As a novel core-shell NPs structure, Au@PVP present not only the chemical stability to iodide/triiodide electrolyte, but also the adhesiveness to dye molecules, which could help to localize most of dye molecules around plasmonic NPs, hence increasing the optical absorption consequently the power conversion efficiency (PCE) of the device. We obtain a PCE enhancement of 30% from 3.3% to 4.3% with incorporation of Au@PVP NPs. Moreover, the device performance with different concentration of Au@PVP NPs from 0 to 12.5 wt% has been studied, and we draw the conclusion that the performance of DSCs could be well improved through enhancing the light absorption by local surface plasmon (LSP) effect from Au@PVP NPs with an optimized concentration.
Broadband Plasmonic Enhancement of High-Efficiency Dye-Sensitized Solar Cells by Incorporating Au@Ag@SiO2 Core-Shell Nanocuboids.

Zhiyong Bao,Nianqing Fu,Yongqiang Qin,Jun Lv,Yan Wang,Jijun He,Yidong Hou,Chenyi Jiao,Dongchu Chen,Yucheng Wu,Ji-Yan Dai

DOI: https://doi.org/10.1021/acsami.9b16245

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:The introduction of plasmonic additives is a promissing approach to boost the efficiency of dye-sensitized solar cell (DSSC) since it may improve the light harvesting of a solar cell. Herein, we design broadband and strong plasmonic absorption Au@Ag@SiO2 nanocuboides (GSS NCs) as nanophotonic inclusions to achieve plasmon-enhanced DSSCs. These multiple resonances absorption arising from GSS NCs can be readily adjusted by altering their structures to complementarily match the absorption spectrum of the dyes, especially in weak absorption zones. By subtly regulating the position of nanophotonic inclusions in the photoanodes, not only the plasmonic near-field enhancement but also far-field light-scattering could be adequately developed to promote the light harvest and thus the efficiency of DSSCs. The resulting solar cells yield an average efficiency of 10.34%, with a champion value of 10.58%. The electromagnetic simulations are consistent with the experimental observations, further corroborating the synergistic effect of plasmonics improvement in these DSSCs.
Phthalocyanine-silver Nanoparticle Structures for Plasmon-Enhanced Dye-Sensitized Solar Cells

Rahim Ghadari,Alireza Sabri,Paria-Sadat Saei,Fan-Tai Kong,Helder M. Marques

DOI: https://doi.org/10.1016/j.solener.2020.01.053

IF: 7.188

2020-01-01

Solar Energy

Abstract:The localized surface plasmon resonance of silver nanoparticles (Ag NPs) was examined to improve the performance of phthalocyanine (MTXPc) in the plasmon-enhanced phthalocyanine-sensitized solar cells. When MTXPc dyes directly conjugated to Ag NPs (MTXPc-AgNPs) were used to sensitize solar cells, both of short-circuit current density (J(SC)) and open-circuit voltage (V-OC) of phthalocyanine-sensitized solar cells were significantly increased. In the case of MTXPc conjugated to Ag@ZIF-8 (MTXPc-Ag@ZIF-8), slightly increasing in the J(SC) compared to alone MTXPc are observable but their V-OC are significantly greater than alone MTXPc. Increasing in the J(SC) and V-OC of the MTXPc-AgNPs and MTXPc-Ag@ZIF-8 lead to improve the performance of phthalocyanine in plasmon-enhanced phthalocyanine-sensitized solar cells compared to alone MTXPc. Also, the examination of the effect of the carboxyl- and sulfonyl-anchored dye (ZnTCPc-AgNPs and ZnTSPc-AgNPs, respectively) in conjunction with plasmonic NPs on the performance of DSSCs showed that ZnTCPc-AgNPs and ZnTSPc-AgNPs perform significantly better than their unsubstituted analogues. The studying the effect of the metal in the central cavity of phthalocyanine using zinc, manganese, iron, cobalt, and nickel showed that the metal in the central cavity of phthalocyanine has the critical role toward the photovoltaic performance of the plasmon-enhanced phthalocyanine-sensitized solar cells.
Optics–electrics Highways: Plasmonic Silver Nanowires@tio2 Core–shell Nanocomposites for Enhanced Dye-Sensitized Solar Cells Performance

Hua Dong,Zhaoxin Wu,Fan Lu,Yucui Gao,Ahmed El-Shafei,Bo Jiao,Shuya Ning,Xun Hou

DOI: https://doi.org/10.1016/j.nanoen.2014.09.011

IF: 17.6

2014-01-01

Nano Energy

Abstract:In this article, the unique bristled silver nanowires@TiO2 core shell nanostructure (AgNW@TiO2) is introduced into the TiO2 photoanode and applied to assemble dye-sensitized solar cells (DSSCs). The effects of the "optics-electrics highways" composites on the photovoltaic and photocatalytic behaviors of DSSCs are investigated in detail. Experiment research and FDTD simulation indicate that both the localized surface plasmon resonance (LSPR) and plasmonic waveguide effect could enhance light harvesting efficiency. By electrical properties and electrochemical analysis, it is demonstrated that the AgNW@TiO2 significantly accelerates electron transport as well as reduces recombination, then the charge collection efficiency of DSSCs is improved. The composite-modified DSSC exhibits the best performance with the power conversion efficiency of 8.84% which is superior to that of the free-modified DSSC with the PCE of 6.16%. (C) 2014 Elsevier Ltd. All rights reserved.
Plasmonic Ag@Oxide Nanoprisms for Enhanced Performance of Organic Solar Cells

Peng Du,Pengtao Jing,Di Li,Yinghui Cao,Zhenyu Liu,Zaicheng Sun

DOI: https://doi.org/10.1002/smll.201402757

IF: 13.3

2015-01-01

Small

Abstract:Localized surface plasmon resonance (LSPR), light scattering, and lowering the series resistance of noble metal nanoparticles (NPs) provide positive effect on the performance of photovoltaic device. However, the exciton recombination on the noble metal NPs accompanying above influences will deteriorate the performance of device. In this report, surface-modified Ag@oxide (TiO2 or SiO2 ) nanoprisms with 1-2 nm shell thickness are developed. The thin film composed of P3HT/Ag@oxides and P3HT:PCBM/Ag@oxides is investigated by absorption, photoluminescence (PL), and transient absorption spectroscopy. The results show a significant absorption, PL enhancement, and long-lived photogenerated polaron in the P3HT/Ag@TiO2 film, indicating the increase of photogenerated exciton population by LSPR of Ag nanoprisms. In the case of P3HT/Ag nanoprisms, partial PL quench and relatively short-lived photogenerated polaron are observed. That indicates that the oxides layer can effectively avoid the exciton recombination. When the Ag@oxide nanoprisms are introduced into the active layer of P3HT:PCBM photovoltaic devices, about 31% of power conversion efficiency enhancement is obtained relative to the reference cell. All these results indicate that Ag@oxides can enhance the performance of the cell, at the same time the ultrathin oxide shell prevents from the exciton recombination.
Preparation and Enhanced Properties of Dye-Sensitized Solar Cells by Surface Plasmon Resonance of Ag Nanoparticles in Nanocomposite Photoanode

Kaimo Guo,Meiya Li,Xiaoli Fang,Xiaolian Liu,Bobby Sebo,Yongdan Zhu,Zhongqiang Hu,Xingzhong Zhao

DOI: https://doi.org/10.1016/j.jpowsour.2012.12.079

IF: 9.2

2013-01-01

Journal of Power Sources

Abstract:A series of TiO2 photoanodes with differing amounts of Ag nanoparticles (NPs) on TiO2 in core-shell form (Ag@TiO2) are prepared and used to make a series of dye-sensitized solar cells (DSSCs). The influence of different amounts of Ag-NPs on the structure and performance of the DSSCs is investigated. Studies indicate that the short-circuit current density (J(sc)), open-circuit voltage (V-oc), charge lifetime and dark current of DSSCs containing Ag-NPs are significantly improved. The best performance is achieved in the DSSCs with 0.15 wt% Ag-NPs additions, with the maximum J(sc) of 10.19 mA cm(-2), highest V-oc of 698 mV and best photoelectric conversion efficiency of 5.33%, significantly superior to that of the DSSCs with pure TiO2 photoanodes. The increase of J(sc) is attributed to the enhanced dye light absorption in strength and spectral range due to the surface plasmon resonance of Ag-NPs in photoanode, while the increase of V-oc may be related to the more negative level of the quasi-Fermi energy of Ag-TiO2 composite system resulting from the added Ag. (C) 2012 Elsevier B.V. All rights reserved.
Plasmon-Enhanced Cell Efficiency in Hybrid Solar Cell Based on CdS Nanorod and Poly (3-Hexythiophene)

Xinmei Liu,Fengming Fu,Weimin Guo

DOI: https://doi.org/10.4028/www.scientific.net/amr.774-776.753

2013-01-01

Advanced Materials Research

Abstract:A bulk-heterjunction hybrid solar cell based on CdS nanorods as electron acceptor and conjugated polymers P3HT (Poly (3-Hexylthiophene)) as donor was fabricated through solution processing. Plasmon-active silver nanoparticle layers were introduced in the hybrid solar cell. Silver nanoparticle layers were fabricated using thermal evaporation deposition of 10 nm of silver thin layers on indium tin oxide (ITO) substrate followed by annealing. Under the surface plasmon excitation in Ag nanoparticles deposited on a semiconductor surface, increasing optical electrical field inside the photoactive layer led to an increased short circuit current density (Jsc) and improved fill factor (FF) of the cell. Consequently, under AM1.5G illumination (100 mW.cm-2), the plasmon-decorated cell based on CdS-nanorods/P3HT showed a four-times increase of the power conversion efficiency (PCE) compared with the undecorated one.
Enhancing the Efficiency of Solid-State Dye-Sensitized Solar Cells with Plasmonic Back Reflectors

I-Kang Ding,Jia Zhu,Wenshan Cai,Soo-Jin Moon

DOI: https://doi.org/10.1109/pvsc.2011.6186453

2011-01-01

Abstract:Solid-state dye-sensitized solar cells (ss-DSCs) are a type of solar cell that replaces the liquid electrolyte in a conventional DSC with a solid-state hole-transport material. SS-DSCs have already achieved power conversion efficiency over 6%, and they do not have problems with potential leakage and corrosion encountered by liquid electrolyte DSCs. However, current ss-DSCs are limited by both pore filling and electron-hole recombination such that the optimal thickness is around 2 μm, which is far too thin to absorb enough light. We show that the efficiency of ss-DSCs can be greatly enhanced by incorporation of plasmonic back reflectors, which consist of two-dimensional (2D) array of silver nanodomes. The plasmonic back reflectors can be fabricated by nanoimprint lithography. They enhance absorption through excitation of plasmonic modes and increased light scattering. SS-DSCs with plasmonic back reflectors show increased external quantum efficiency, particularly in the long wavelength region of the dye's absorption band. This approach is effective in increasing the efficiencies of ss-DSCs with normal thickness (2 μm) made with both ruthenium-complex sensitizers and strong-absorbing organic sensitizers, and the short-circuit photocurrents increased by 16% and 12%, respectively. They achieve power conversion efficiencies of 3.9% and 5.9%, on par with the world record for the devices with the same dyes. In addition to the device data, results on the theoretical modeling of plasmonic and photonic effects will also be presented.
The Preparation and Improved Properties of Dye-Sensitized Solar Cells by Surface Plasmon Resonace of Ag Nanoparticles

GUO Kaimo,FANG Xiaoli,HU Zhongqiang,LI Meiya

DOI: https://doi.org/10.14188/j.1671-8836.2012.05.002

2012-01-01

Abstract:A series of TiO2 photoanodes doped with different amounts of Ag nanoparticles(NPS) and prepared by the hydrothermal method were used to make a series of dye-sensitised solar cells(DSSCs).The influence of different amounts of Ag NPS on the structure and performance of DSSCs were investigated.Studies indicated that the incorporation of the Ag NPS significantly enhanced the light absorption of dye loaded on surface of TiO2 film and the short-circuit current density(Jsc).When the content of Ag NPS was 0.20%,the DSSC achieved the best performance with the largest short-circuit current of 10.66 mA/cm2,the highest open-circuit voltage of 697 mV and the photoelectric conversion efficiency of 5.59%,significantly superior to the DSSC with no Ag incorporation.The improved performances were attributed to the enhanced light absorption of dye resulted from the surface plasmon resonance of Ag NPS in photoanode.
Coupling Plasmonic Nanoparticles with TiO2 Nanotube Photonic Crystals for Enhanced Dye-Sensitized Solar Cells Performance

Min Guo,Jia Chen,Jun Zhang,Haijun Su,Lin Liu,Nianqing Fu,Keyu Xie

DOI: https://doi.org/10.1016/j.electacta.2018.01.039

IF: 6.6

2018-01-01

Electrochimica Acta

Abstract:In order to break through the limit of low power conversion efficiency (PCE) of dye-sensitized solar cell (DSSC) with single photon management architecture in photoanode, herein, we propose a novel architecture, composed of a TiO2 nanotube photonic crystal (TiO2 NTPC) layer and in-suit deposited Au plasmonic nanoparticles (Au NPs), as photoanode for DSSC applications. The designed photoanode is expected to significantly increase the light harvesting in DSSCs, due to the synergistic effect of the photonic crystal (PC) effect originates from TiO2 NTPC and the surface plasmon resonance (SPR) effect from Au NPs. This synergistic effect of the newly designed photoanode and its functionality in DSSCs are discussed by both experimental and simulated results. Moreover, when the SPR band of Au NPs has been tailored to best match with the bandgap of TiO2 NTPC, the maximum enhancement in power conversion efficiency (PCE, 44.7%), which exceeds the sum enhancement producing by coupling individual TiO2 NTPC (22.1%) or Au NPs (18.0%), has been achieved by introducing the designed Au NPs/TiO2 NTPC photoanode, yielding a PCE of 5.63% in the NT-based DSSCs. The work presented here provides new insights into the design and application of SPR/PC coupling architectures for high efficient light management and synergistically enhanced light harvesting in photovoltaic devices.
Plasmonic Enhancement of Au Nanoparticle–Embedded Single-Crystalline ZnO Nanowire Dye-Sensitized Solar Cells

mingyen lu,chenyu tsai,hsuehan chen,yating liang,kuoping chen,silvija gradecak,shangjr gwo,lihjuann chen

DOI: https://doi.org/10.1016/j.nanoen.2015.12.026

IF: 17.6

2016-01-01

Nano Energy

Abstract:This paper describes the enhanced efficiency of dye-sensitized solar cells (DSSCs) incorporating Au nanoparticle–embedded single-crystalline ZnO nanowire (Au NPs@ZnO NW) arrays. We fabricated these Au NPs@ZnO NW arrays through sequential hydrothermal ZnO growth, with the Au NPs deposited in between the two ZnO growth processes. Interestingly, despite the presence of embedded Au NPs, the ZnO NWs exhibited continuously matched periodic atomic arrangements across the ZnO NW core and shells, indicating that they were single-crystalline. The surface plasmon resonance peaks of the Au NPs on the ZnO NW arrays and of the Au NPs@ZnO NW arrays appeared near 526 and 574nm, respectively; the red-shift of the latter signal confirmed the embedded geometry of the Au NPs in the ZnO NW arrays. Photovoltaic measurements of the Au NPs@ZnO NW DSSCs revealed enhancements in efficiency that depended on the lengths of the ZnO NWs in the arrays; these efficiencies were all greater than those of corresponding ZnO NW–only DSSCs by at least 20%. In accordance with the geometry of our devices and the improved dye absorption within them, it appears that the near-field localized surface plasmon of the Au NPs in the ZnO NWs was the principal factor governing the enhanced power conversion efficiency.
Plasmonic dye-sensitized solar cells through collapsible gold nanofingers

Wenruo Fang,Pan Hu,Zhenqiu Wu,Youfeng Xiao,Yunxia Sui,Dalong Pan,Guangxu Su,Mingwei Zhu,Peng Zhan,Fanxin Liu,Wei Wu

DOI: https://doi.org/10.1088/1361-6528/ac04d2

IF: 3.5

2021-06-09

Nanotechnology

Abstract:Plasmonic nanostructures are successfully demonstrated in solar cells due to their broad spectra-selective resonance in the range of ultraviolet to near-infrared, and thus light absorption can be mostly improved and power conversion efficiency (PCE) further. Here, we demonstrate plasmonic dye-sensitized solar cells (DSSCs) using collapsible Au nanofingers to build photoanode to enhance light absorption. In this plasmonic DSSCs, by balancing local field enhancement due to gap-plasmon resonance and dye fluorescence quenching, the optimal gap size in collapsed Au/Al2O3/Au nanofingers is designed by twice the Al2O3 thickness and then deposited a TiO2 layer as photoanode. The results show that the PCE of DSSCs is mostly improved as compared to DSSCs with photoanode of Au/Al2O3/TiO2 films, which can be ascribed to the coupled local field enhancement within the sub-nanometer gaps. In addition, fluorescence of dyes on plasmonic nanofingers is nearly 10 times higher than plain Au/Al2O3/TiO2 films, which further proves the dye absorption enhancement. These plasmonic nanofingers enable the precise engineering of gap-plasmon modes and can be scaled up to wafer scale with low cost by the nanoimprint lithography technique, which suggests the feasibility of applying our result in constructing the photoanode for other types of solar cells.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Plasmonic-based Solar Cell: Geometrical Optimization of 1D-nanostructured Grating for Enhanced Efficiency

Muzafer Iqbal,Muhammad Abrar,Tahir Iqbal,Irfan Ahmed,M. A. Sayed,A. F. Abd El-Rehim,Atif Mossad Ali

DOI: https://doi.org/10.1007/s11468-022-01717-5

IF: 2.726

2022-11-12

Plasmonics

Abstract:This study reports the generation of surface plasmon polariton (SPPs) by varied geometrical effects of gold (Au) and silver (Ag) plasmonic grating to realize efficiency enhancement of solar cell by finite elemental analysis (FEA) using COMSOL RF module 5.3a. This technique is quite helpful for far-field and near-field analysis which is required for the confirmation of the excitation of the SPPs. Plasmonic effect can be utilized from metallic materials; the upshot of Au and Ag plasmonic grating assembly upon light absorption in a-Si photovoltaic device has been investigated. In this paper, various plasmonic grating coupling setups for Au and Ag have been designed and studied the transmission spectra with varying grating slit width sizes (80–540) nm and thicknesses 40 nm, 50 nm, and 60 nm but constant periodicity of unit cell (Λ = 720 nm). The slit width of 240 nm nearly one-third of periodicity of the grating is optimum for efficient excitation of the SPPs and hence contributes more for efficiency enhancement of the solar cell. Quite interestingly, resonance wavelength and its variation in full width at half maximum (FWHM) with fixed values of Au and Ag thicknesses has been observed. This paper also reports the study of coupling efficiency for Au and Ag plasmonic gratings. Effective excitation of SPPs inclines toward increased electric/magnetic fields in proximity of slit, henceforth growing the light absorption in substratum. This finding is associated with the existence of strongest plasmonic mode known as fundamental mode/harmonics. Variation in the electric field y-component (Ey) and electric field normal component (E_norm) across cross sectional length of solar cell for Au plasmonic grating with slit thickness of 50 nm has been reported to be efficient in a-Si thin-film solar cell to attain better photoabsorption. This type of geometry can be utilized for solar cells for enhanced absorption of solar spectrum to design an efficient photovoltaic device.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry, physical
Plasmon-enhanced Dye-Sensitized Solar Cells Through Porphyrin-Silver Nanoparticle Hybrid Structures: Experimental and Computational Studies

Rahim Ghadari,Alireza Sabri,Paria-Sadat Saei,Fantai Kong,Yousef Mohammadzadeh,Emre Guzel

DOI: https://doi.org/10.1016/j.jpowsour.2021.230407

IF: 9.2

2021-01-01

Journal of Power Sources

Abstract:Surface plasmon resonance of silver nanoparticles (Ag NPs) was used to improve light absorption of porphyrins in plasmon-enhanced porphyrin-sensitized solar cells (PSSCs). Porphyrins with different substituents consisting -H, -Me, -MeO, -F, -Cl, -Br, -CO2H, -SO3H, -NO2, and -NH2 were used to study the effect of the interactions between photoactive dye molecules and plasmonic Ag NPs on the performance of PSSCs. The obtained results revealed that zinc tetra(4-carboxyphenyl)porphyrin and zinc tetra(4-aminophenyl)porphyrin have made the biggest impact on the performance of plasmon-enhanced PSSCs. Computational studies were done to study the electronic properties of porphyrin molecules with electron-withdrawing and electron-donating substituents interacted with Ag NPs. The theoretical studies confirmed that the electronic nature of substituents of porphyrins has a considerable effect on the electronic properties of porphyrin-AgNPs systems. In continue, Ag@ZIF-8 coreshell NPs were prepared to overcome the challenge of corrosion of Ag plasmonic nanoparticles. The results showed that using porphyrin-Ag@ZIF-8 systems, in many cases, the performance of PSSCs is increased relative to corresponding porphyrins but is decreased relative to porphyrin-AgNPs systems.
Surface Plasmon Enhancement Solar Cells and Their Research Progresses

Peng Yingcai,Ma Lei,Shen Bo,Jiang Bing,Chen Yihao

DOI: https://doi.org/10.3969/j.issn.1671-4776.2013.07.003

2013-01-01

Abstract:Plasmon light-scattering and light-trapping effects generated on the surface of thin film solar cells by various metal nanoparticles can increase effectively the photon energy absorption of solar cells,thus enhancing the conversion efficiency of solar cells.Firstly,the plasmon enhancement effects generated on the surface of thin film solar cells and the structure types of surface plasmon enhancement solar cells are described.Then,the progresses on photovoltaic properties of some typical surface plasmon enhancement solar cells are reviewed,such as silicon-based film surface plasmon enhancement solar cells,quantum well surface plasmon enhancement solar cells,as well as organic film surface plasmon enhancement solar cells.Finally,some physics thinking and technical strategies to develop surface plasmon enhancement solar cells are proposed,such as the explanation of the physical mechanism on surface plasmon enhancement effects,the elaboration of the internal relation between properties of metal nanoparticles and plasmon enhancement effects,the choice of new metal nanoparticle materials and the design of optimum metal nanostructures,etc.
Plasmonic Enhanced Light Absorption of Solar Cells with Metal Nanoparticles

Fang Liu,Di Qu,Qi Xu,Wanlu Xie,Yidong Huang

DOI: https://doi.org/10.1364/e2.2011.jwe11

2011-01-01

Abstract:Get PDF Email Share Share with Facebook Tweet This Post on reddit Share with LinkedIn Add to CiteULike Add to Mendeley Add to BibSonomy Get Citation Copy Citation Text F. Liu, D. Qu, Q. Xu, W. Xie, and Y. Huang, "Plasmonic Enhanced Light Absorption of Solar Cells with Metal Nanoparticles," in Renewable Energy and the Environment, OSA Technical Digest (CD) (Optica Publishing Group, 2011), paper JWE11. Export Citation BibTex Endnote (RIS) HTML Plain Text Citation alert Save article
Plasmonic enhancement of light-harvesting efficiency in tandem dye-sensitized solar cells using multiplexed gold core/silica shell nanorods

Yan-Zhen Zheng,Xia Tao,Jinwen Zhang,Xue-Sen Lai,Nan Li

DOI: https://doi.org/10.1016/j.jpowsour.2017.11.072

IF: 9.2

2018-01-01

Journal of Power Sources

Abstract:Incorporation of plasmonic metal nanocrystals is a promising approach for broadening and enhancing the light harvesting of dye-sensitized solar cells (DSSCs). In this work, we report a facile and versatile route to tune the photoresponse of tandem DSSCs via incorporating Au nanorods with multiplexed length-to-diameter aspect ratios in the two sub-cells. Plasmonic Au nanorods with length-to-diameter aspect ratio of 2.5 (Au NRs-1) and 3.9 (Au NRs-2) are prepared, exhibiting their plasmon band at 500–700 nm and 500–900 nm, respectively. Au NRs-1 core/SiO2 shell (Au NRs@SiO2-1) and Au NRs-2 core/SiO2 shell (Au NRs@SiO2-2) are separately incorporated in TiO2 photoanodes and then coupled with commercial dye N719 and N749 for the top and bottom sub-cells of a tandem DSSC, achieving a power conversion efficiency (PCE) of 10.73% for relative to 9.02% of reference (TiO2 only) devices. By virtue of morphological, spectral and electrochemical characterizations and analysis, we find that the integration of Au NRs within dye-sensitized TiO2 photoanode film enables to increase the sunlight harvesting from visible to near infrared region by plasmonic enhancement effect, reduce the charge recombination probability and facilitate charge transport via Au NRs, leading to enhancement of PCE.

Plasmon Enhanced Dye-Sensitized Solar Cells Using Nanoparticles of Different Geometries and Materials

Efficiency Enhancement of Organic Solar Cells by Using Shape‐Dependent Broadband Plasmonic Absorption in Metallic Nanoparticles

Influence of Geometry of Metallic Nanoparticles on Absorption of Thin-Film Organic Solar Cells: A Critical Examination.

Dual Plasmonic Nanostructures for High Performance Inverted Organic Solar Cells.

Plasmonic Nanoparticles Enhanced Dye-Sensitized Solar Cells

Broadband Plasmonic Enhancement of High-Efficiency Dye-Sensitized Solar Cells by Incorporating Au@Ag@SiO2 Core-Shell Nanocuboids.

Phthalocyanine-silver Nanoparticle Structures for Plasmon-Enhanced Dye-Sensitized Solar Cells

Optics–electrics Highways: Plasmonic Silver Nanowires@tio2 Core–shell Nanocomposites for Enhanced Dye-Sensitized Solar Cells Performance

Plasmonic Ag@Oxide Nanoprisms for Enhanced Performance of Organic Solar Cells

Preparation and Enhanced Properties of Dye-Sensitized Solar Cells by Surface Plasmon Resonance of Ag Nanoparticles in Nanocomposite Photoanode

Plasmon-Enhanced Cell Efficiency in Hybrid Solar Cell Based on CdS Nanorod and Poly (3-Hexythiophene)

Enhancing the Efficiency of Solid-State Dye-Sensitized Solar Cells with Plasmonic Back Reflectors

The Preparation and Improved Properties of Dye-Sensitized Solar Cells by Surface Plasmon Resonace of Ag Nanoparticles

Coupling Plasmonic Nanoparticles with TiO2 Nanotube Photonic Crystals for Enhanced Dye-Sensitized Solar Cells Performance

Plasmonic Enhancement of Au Nanoparticle–Embedded Single-Crystalline ZnO Nanowire Dye-Sensitized Solar Cells

Plasmonic dye-sensitized solar cells through collapsible gold nanofingers

Plasmonic-based Solar Cell: Geometrical Optimization of 1D-nanostructured Grating for Enhanced Efficiency

Plasmon-enhanced Dye-Sensitized Solar Cells Through Porphyrin-Silver Nanoparticle Hybrid Structures: Experimental and Computational Studies

Surface Plasmon Enhancement Solar Cells and Their Research Progresses

Plasmonic Enhanced Light Absorption of Solar Cells with Metal Nanoparticles

Plasmonic enhancement of light-harvesting efficiency in tandem dye-sensitized solar cells using multiplexed gold core/silica shell nanorods