Abstract:The mechanical properties of solder joints highly depend on the interfacial reaction between the solders and the metallization on substrates. In this work, we electroplated Co–P films with various compositions on the Cu pads of printed circuit boards and fabricated Sn-3.8 wt% Ag-0.7 wt% Cu/Co–P ball grid array (BGA) solder joints. The BGA solder joints were annealed at 150 °C for 100, 200, 500, and 1000 h and the shear strength of these joints was measured. When the P content of the Co–P metallization was increased from 2.3 to 18.8 at.%, the shear strength after 1000 h annealing initially rose to 107.9 MPa at a P content of 8.5 at.%, then decreased to 84.3 MPa at a P content of 12.5 at.%, and again increased to 96.0 MPa at a P content of 18.8 at.%. The enhancement of the shear strength of the joints with Co-8.5 at.% P, Co-12.5 at.% P, and Co-18.8 at.% P films was 109.5%, 63.7%, and 86.4% in comparison to the joints without Co–P metallization, respectively. The interfacial reaction between the Sn–Ag–Cu (SAC) solder and Co–P films during annealing and the fractured surfaces of the solder joints after the shear test were studied. For the joints with Co-8.5 at.% P and Co-18.8 at.% P films, a thick layer of CoSn3 was formed at the interfaces during annealing, which enhanced the shear strength. For the joints with Co-12.5 at.% P metallization, a thin layer of Co–Sn–P was formed at the interfaces and was peeled off layer by layer with prolongation of the annealing time. The spalled Co–Sn–P was mixed with the solder matrix, increasing the shear strength of the solder joints. The shear strength of the SAC/Co-12.5 at.% P joints was less than that of the joints with Co-8.5 at.% P and Co-18.8 at.% P films because no CoSn3 formed. Therefore, the composition of Co–P metallization played an important role in the interfacial reaction of the SAC/Co–P solder joints, which in turn affected the shear strength of the solder joints. Our experimental results show that the electroplated Co–P film is a promising candidate as the metallization for BGA solder joints.

Reliability of Sn-Pb Solder Joints with Cu and Co-P Surface Finishes under Thermal Cycling

IMC growth and shear strength of Sn–Ag–Cu/Co–P ball grid array solder joints under thermal cycling

Evolution Of Intermetallic Compounds In Pbga Sn-Ag-Cu Solder Joints During Thermal Cycling Testing

Influence of Thermal Cycling on the Microstructure and Shear Strength of Sn3.5ag0.75cu and Sn63pb37 Solder Joints on Au/Ni Metallization

Significantly enhanced shear strength of Sn-Ag-Cu/Co-P ball grid array solder joints by CoSn<inf>3</inf> intermetallic compound

Microstructure, IMCs layer and shear property of Sn-9Zn solder joints reinforced by Cu nanoparticles during thermal cycling

Influence of thermal shock cycles on Sn-37Pb solder bumps

Dependence of Shear Strength of Sn–3.8Ag–0.7Cu/Co–P Solder Joints on the P Content of Co–P Metallization

Effect of Surface Finish of Substrate on Mechanical Reliability of in-48SN Solder Joints in Moems Package

Interfacial Microstructure and Mechanical Reliability of Sn-58Bi/ENEPIG Solder Joints

Microstructure, orientation and damage evolution in SnPb, SnAgCu, and mixed solder interconnects under thermomechanical stress

Effect of Thermal Cycling on the Growth of Intermetallic Compounds at the Sn-Zn-Bi-In-P Lead-Free Solder/cu Interface

Failure Behavior of SnAgCu/Cu Solder Joint Subjected to Thermal Cycling

Growth and shear strength of intermetallic compounds in Sn-Ag-Cu solder joints

Solder Volume Effects on the Microstructure Evolution and Shear Fracture Behavior of Ball Grid Array Structure Sn-3.0Ag-0.5Cu Solder Interconnects

Microstructural Evolution and Failure Mechanism of 62sn36pb2ag/cu Solder Joint During Thermal Cycling

Characterization of Mechanical Performance of Sn/Ag/Cu Solder Joints with Different Component Lead Coatings

Microstructure and mechanical properties of SnAgCu/Cu solder joint during thermal cycle

Insights into Relationship Between Mechanical Behavior and Microstructure Evolution of Sn-1.0Ag-0.5Cu-GNSs/Cu Joint During Thermal Cycling

Effect of electromigration on the microstructural evolution and shear fracture behavior of mixed assembled Cu/Sn–3.0Ag–0.5Cu-ball/Sn–58Bi-paste/Cu joints in board-level packaging

Effect Of Microstructure And Imc On Single Snagcu Solder Joint By Rapid Thermal Cycles