Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Gait Modification and Optimization Using Neural Network-Genetic Algorithm Approach: Application to Knee Rehabilitation.

A neural network approach for determining gait modifications to reduce the contact force in knee joint implant

Mapping-Based Dosage of Gait Modification Selection for Multi-Parameter, Subject-Specific Gait Retraining

Feasibility of Wearable Haptic Biofeedback Training for Reducing the Knee Abduction Moment During Overground Walking

A Real-Time Topography of Maximum Contact Pressure Distribution at Medial Tibiofemoral Knee Implant During Gait: Application to Knee Rehabilitation.

Feed forward artificial neural network to predict contact force at medial knee joint: Application to gait modification

Gait Pattern Adaptation for an Active Lower-Limb Orthosis Based on Neural Networks

Humanoid Walking Gait Optimization Using GA-Based Neural Network

Gait-symmetry-based Human-in-the-loop Optimization for Unilateral Transtibial Amputees with Robotic Prostheses

Optimization Reduces Knee-Joint Forces During Walking and Squatting: Validating the Inverse Dynamics Approach for Full Body Movements on Instrumented Knee Prostheses

Torque Curve Optimization of Ankle Push-Off in Walking Bipedal Robots Using Genetic Algorithm

Finding Emergent Gait Patterns May Reduce Progression of Knee Osteoarthritis in a Clinically Relevant Time Frame

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Gait pattern modification based on ground contact adaptation using the robot-assisted training platform (RATP)

Emulating Human Kinematic Behavior on Lower-Limb Prostheses via Multi-Contact Models and Force-Based Nonlinear Control

Gait-to-Contact (G2C): A novel deep learning framework to predict total knee replacement wear from gait patterns

Predicting Knee Joint Contact Forces During Normal Walking Using Kinematic Inputs with A Long-Short Term Neural Network

Design and Speed-Adaptive Control of a Powered Geared Five-Bar Prosthetic Knee Using BP Neural Network Gait Recognition

Kinematic Performance of a Customizable Single Degree-of-Freedom Gait Trainer for Cost-Effective Therapy Aimed at Neuromuscular Impairments

Evaluation of Optimal Control Approaches for Predicting Active Knee-Ankle-Foot-Orthosis Motion for Individuals With Spinal Cord Injury

An Optimization Method Tracking EMG, Ground Reactions Forces, and Marker Trajectories for Musculo-Tendon Forces Estimation in Equinus Gait