Abstract:Balancing interfacial stability and Li+ transfer kinetics through surface engineering is a key challenge in developing high-performance battery materials. Although conformal coating enabled by atomic layer deposition (ALD) has shown great promise in controlling impedance increase upon cycling by minimizing side reactions at the electrode–electrolyte interface, the coating layer itself usually exhibits poor Li+ conductivity and impedes surface charge transfer. In this work, we have shown that by carefully controlling postannealing temperature of an ultrathin ZrO2 film prepared by ALD, Zr4+ surface doping could be achieved for Ni-rich layered oxides to accelerate the charge transfer yet provide sufficient protection. Using single-crystal LiNi0.6Mn0.2Co0.2O2 as a model material, we have shown that surface Zr4+ doping combined with ZrO2 coating can enhance both the cycle performance and rate capability during high-voltage operation. Surface doping via controllable postannealing of ALD surface coating layer reveals an attractive path toward developing stable and Li+-conductive interfaces for single-crystal battery materials.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acs.nanolett.0c03778?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acs.nanolett.0c03778</a>.Quasi in situ X-ray photoelectron spectroscopy (XPS) characterizations of Zr 3d and Ni 2p (Figure S1), XPS characterizations of O 1s (Figure S2), energy-dispersive spectroscopy (EDS) mapping of 50-ZrO2-700 °C-NCM (Figure S3), cross-sectional scanning electron microscopy (SEM) images of SC-NCM and 5-ZrO2-NCM electrode collected after 50 cycles (Figure S4), reproducible cycle and rate performance of 5-ZrO2-500 °C-NCM (Figure S5), XPS characterizations of F 1s (Figure S6), SEM characterizations of SC-NCM; 5-ZrO2-NCM; 5-ZrO2-500 °C-NCM; 5-ZrO2-700 °C-NCM after 50 cycles (Figure S7), cycle stability of NCM cathodes at 1 C (180 mA/g) in this study compared to literature reports (Table S1) (<a class="ext-link" href="/doi/suppl/10.1021/acs.nanolett.0c03778/suppl_file/nl0c03778_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Tuning of surface morphology in Li layered oxide cathode materials

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Increase and discretization of the energy barrier for individual LiNixCoyMnyO2 (x+2y=1) particles with the growth of a Li2CO3 surface film

Ab Initio Study on Surface Segregation and Anisotropy of Ni-Rich LiNi 1-2y Co y Mn y O 2 (NCM) (y ≤ 0.1) Cathodes.

Tuning Li-enrichment in High-Ni Layered Oxide Cathodes to Optimize Electrochemical Performance for Li-ion Battery

Cooling Induced Surface Reconstruction During Synthesis of High‐Ni Layered Oxides

Tuning of Thermal Stability in Layered Li(NixMnyCoz)O2

Spreading monoclinic boundary network between hexagonal primary grains for high performance Ni-rich cathode materials

Mutual modulation between surface chemistry and bulk microstructure within secondary particles of nickel-rich layered oxides

Simultaneous Enhancement of Interfacial Stability and Kinetics of Single-Crystal LiNi 0.6 Mn 0.2 Co 0.2 O 2 through Optimized Surface Coating and Doping

Modifying surface chemistry and stress concentration to enable highly stable ultrahigh-Ni cathodes

Ni and Co Segregations on Selective Surface Facets and Rational Design of Layered Lithium Transition‐Metal Oxide Cathodes

Synergistic Effect of B-Nb Co-modified to Achieve Crystal Structure and Interface Tuning for Ni-rich Cathode

Surface Coupling between Mechanical and Electric Fields Empowering Ni‐Rich Cathodes with Superior Cyclabilities for Lithium‐Ion Batteries

Superior Cycle Stability of Single Crystal Nickel-Rich Layered Oxides with Micron-Scale Grain Size as Cathode Material for Lithium Ion Batteries

Surface modification single crystal Li-rich Li1.2Mn0.54Ni0.13Co0.13O2 as high performance cathode materials for Li-ion batteries

(Digital Presentation) Simultaneous Transforming Residual Lithium Compounds and Stabilizing Surface Lattice Oxygen for Ni-Rich Cathode Via Atomic Layer Deposition and Post-Annealing

Surface Atomic Rearrangement with High Cation Ordering for Ultra-Stable Single-Crystal Ni-Rich Co-Less Cathode Materials

Improving the Performance of LiNi 0.925 Co 0.065 Mn 0.01 O 2 via Ti 4+ & Nb 5+ Co-Modifications

Enhancing the Integral Structural and Thermal Stability of Ultrahigh-Ni Cathodes via Morphology Refinement and In Situ Interfacial Engineering