Abstract:Benzene-based 1,1-dicyanomethylene-3-indanone (IC) derivatives have been widely used as the end-group to construct high-performance A-D-A type non-fullerene acceptors (NFAs). Extension of the end-group conjugation of NFAs is a rational strategy to facilitate intermolecular stacking of the end-groups which are responsible for efficient electron transportation. A bicyclic benzothiophene-based end-group acceptor, 2-(3-oxo-2,3-dihydro-1H-benzo[b]cyclopenta[d]thiophen-1-ylidene) malononitrile), denoted as -BC was designed and synthesized. Knoevenagel condensation of the unsymmetrical 1,3-diketo-precursor with one equivalent of malononitrile selectively reacts with the keto group attached at the-position of thiophene unit, leading to the isomerically pure benzothiophene-fused -BC. The well-defined -BC with extended conjugation was condensed with three different ladder-type diformylated donors to form three new A-D-A NFAs named as BDCPDT-BC, DTCC-BC and ITBC, respectively. The corresponding IC-based BDCPDT-IC, DTCC-IC and ITIC model compounds were also synthesized for comparison. The incorporation of electron-rich benzothiophene unit in the end-group upshifts the LUMO energy levels of the NFAs, which beneficially enlarges the Voc values. On the other hand, the benzothiophene unit in -BC not also imparts an optical transition in the shorter wavelengths around 340-400 nm for better light harvesting ability but also promotes antiparallel  stacking of the end-groups for efficient electron transport. The OPV devices using BC-based NFAs as the n-type acceptor and PBDB-T as the p-type polymer all showed the improved Voc and Jsc values. The BDCPDT-BC-, and DTCC-BC-based devices exhibited a PCE of 10.82% and 10.74%, respectively, which outperformed the corresponding BDCPDT-IC-, and DTCC-IC-based devices (9.33% and 9.25%). More importantly, the ITBC-based device delivered a highest PCE of 12.07% with a Jsc of 19.90 mA/cm2, a Voc of 0.94 V, and an FF of 64.51%, representing a 14% improvement relative to the traditional ITIC-based device (10.5%).

Fused ring non-fullerene acceptors with benzothiophene dioxide end groups and their side chain effect investigations

Benzyl side-chain engineering of non-fullerene acceptors for efficient organic solar cells

Isomerically Pure Benzothiophene-Incorporated Acceptor: Achieving Improved Voc and Jsc of Nonfullerene Organic Solar Cells via End Group Manipulation.

Small-Molecule Acceptor Based on the Heptacyclic Benzodi(cyclopentadithiophene) Unit for Highly Efficient Nonfullerene Organic Solar Cells

Hybrid Nonfused-Ring Electron Acceptors with Fullerene Pendant for High-Efficiency Organic Solar Cells

Fused‐Ring Core Engineering for Small Molecule Acceptors Enable High‐Performance Nonfullerene Polymer Solar Cells

Theoretical Study on Functionalizing A–D–A Type Non‐Fullerene Acceptor by Fused Rings and Side Chains for Organic Solar Cells

Non-fused Polymerized Small-Molecule Acceptors with a Benzothiadiazole Core for All-Polymer Solar Cells.

Unconjugated Side‐Chain Engineering Enables Small Molecular Acceptors for Highly Efficient Non‐Fullerene Organic Solar Cells: Insights into the Fine‐Tuning of Acceptor Properties and Micromorphology

Low-cost and completely non-fused small-molecule acceptors based on tetrathiophene featuring 3,5-dialkylthiophene side chain enable efficient organic solar cells

Photodynamic Investigation on the Synergistic Effects of Aromatic Side Chains with Alkylthio Substituents in Nonfullerene Organic Solar Cells

Side-chain engineering of nonfullerene small-molecule acceptors for organic solar cells

Alkyl‐Chain Branching of Non‐Fullerene Acceptors Flanking Conjugated Side Groups toward Highly Efficient Organic Solar Cells

Simultaneous Tuning of Alkyl Chains and End Groups in Non-fused Ring Electron Acceptors for Efficient and Stable Organic Solar Cells

Electron-Deficient and Quinoid Central Unit Engineering for Unfused Ring-Based A1-D-A2-D-A1-Type Acceptor Enables High Performance Nonfullerene Polymer Solar Cells with High Voc and PCE Simultaneously

Effects of the Isomerized Thiophene-Fused Ending Groups on the Performances of Twisted Non-Fullerene Acceptor-Based Polymer Solar Cells.

Nonfullerene acceptors based on extended fused rings flanked with benzothiadiazolylmethylenemalononitrile for polymer solar cells

A Non‐Fullerene Acceptor with Chlorinated Thienyl Conjugated Side Chains for High‐Performance Polymer Solar Cells Via Toluene Processing

High-Efficiency Organic Solar Cells enabled by Nonfullerene Acceptors with Varying Alkyloxy Substitution Position of phenyl Outer Side Chains

Enhanced photovoltaic performance of A–D–A'–D–A type non-fused ring electron acceptors via side chain engineering

Enhancing the performance of non-fullerene organic solar cells through side-chain engineering of asymmetrical non-fused-ring electron acceptors