Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Heterogeneous Mediator Enabling Three‐Dimensional Growth of Lithium Sulfide for High‐Performance Lithium–Sulfur Batteries

Selective Adsorption and Electrocatalysis of Polysulfides Through Hexatomic Nickel Clusters Embedded in N-Doped Graphene Toward High-Performance Li-S Batteries

Synergistic Adsorption-Electrocatalysis of 2D/2D Heterostructure Toward High Performance Li-S Batteries

Heteroelectrocatalyst for optimizing polysulfides in high-efficiency Li S batteries

A strategy to achieve high loading and high energy density Li-S batteries

Enhanced Electrochemical Kinetics with Highly Dispersed Conductive and Electrocatalytic Mediators for Lithium–Sulfur Batteries

Three-Dimensionally Hierarchical Ni/Ni3S2/S Cathode for Lithium-Sulfur Battery.

Three-dimensional Spongy Framework As Superlyophilic, Strongly Absorbing, and Electrocatalytic Polysulfide Reservoir Layer for High-Rate and Long-Cycling Lithium-Sulfur Batteries

Heterostructure Mo2C/α-MoO3/G Catalyst Based Heterogeneous Catalysis/deposition Mechanism for High-Performance Li-S Battery

Facile Synthesis of Heterostructured MoS 2 –MoO 3 Nanosheets with Active Electrocatalytic Sites for High-Performance Lithium–Sulfur Batteries

Cathode Nanostructuring and Separator Modification for High-Performance Lithium-Sulfur Batteries

Rich Heterointerfaces Enabling Rapid Polysulfides Conversion and Regulated Li2S Deposition for High-Performance Lithium-Sulfur Batteries.

Tuning Dual-Atom Mediator Toward High-Rate Bidirectional Polysulfide Conversion in Li-S Batteries

Integration of nickel phosphide nanodot-enriched 3D graphene-like carbon with carbon fibers as self-supported sulfur hosts for advanced lithium sulfur batteries

Insight into MoS 2 –MoN Heterostructure to Accelerate Polysulfide Conversion toward High‐Energy‐Density Lithium–Sulfur Batteries

Direct insight into sulfiphilicity-lithiophilicity design of bifunctional heteroatom-doped graphene mediator toward durable Li-S batteries

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

Heterostructured Mn3O4‐MnS Multi‐Shelled Hollow Spheres for Enhanced Polysulfide Regulation in Lithium–Sulfur Batteries

Freestanding Agaric-Like Molybdenum Carbide/graphene/n-Doped Carbon Foam As Effective Polysulfide Anchor and Catalyst for High Performance Lithium Sulfur Batteries

LDH-derived Co0.5Ni0.5Te2 Dispersed in 3D Carbon Sheets as Separator Modifier to Enable Kinetics-Accelerated Lithium-Sulfur Batteries

Coupling a Sponge Metal Fibers Skeleton with In Situ Surface Engineering to Achieve Advanced Electrodes for Flexible Lithium–Sulfur Batteries