Abstract:In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 μm to 4.1 μm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 μm to 7.24 μm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.

Effect of severe plastic deformation on microstructure and properties of Al-Cu-Mg-Ag aluminum alloys

Effect of plastic deformation on microstructure and properties of high strength Al-Cu-Li-X aluminum-lithium alloy

EFFECT OF PRE-DEFORMATION ON AGE- HARDENING AND MICROSTRUCTURE IN Al-Mg-Si-Cu ALLOY

The Role of Plastic Deformation on Microstructure and Mechanical Properties of 2197 Al-Li Alloy

Effect of Equal Channel Angular Pressing on Microstructure and Properties of Al-Cu-Mg-Ag Aluminum Alloys

Effect of pre-deformation on microstructures and mechanical properties of high purity Al–Cu–Mg alloy

EFFECTS OF DEFORMATION ON THE MICROSTRUCTURE AND PROPERTIES OF 6082 ALUMINUM ALLOY

Effect of pre-stretching deformation treatment process on microstructure and mechanical properties of Al-Cu-Mg alloy

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Extruded Al–4Cu–1Li–0.4Mg–0.4Ag–0.18Zr Alloy

Influence of Cryogenic Deformation and Post-Deform Aging on Microstructure and Mechanical Properties of Al-Cu Alloy

Influence of Severe Plastic Deformation Degree on Subsequent Annealing Microstructures and Properties of Al-4wt.%Cu Alloys

Effects of Severe Cold Plastic Deformation on the Microstructure and Properties of 2024 Aluminum Alloy

Effects of pre-deformation on microstructure, mechanical properties and corrosion performance of an Al-Cu-Mg-Ag alloys

Superplastic Deformation of a Heat-Resistant Al–Cu–Mg–Ag–Mn Alloy

Experimental and Simulation Study for the Influence of Thermal Pre-Deformation on Subsequent Aging Precipitation Kinetics of Al-Zn-Mg-Cu Alloy

Effect of Severe Plastic Deformation at Ambient Temperature on Microstructures and Mechanical Properties of Aluminum Alloy 2519

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

Thermomechanical Treatment of High Strength Al-Cu-Li-X Aluminum-Lithium Alloy

Effect of Deformation Processes on Properties of Cu-Cr-Zr Alloy

Hot Deformation Behavior and Microstructure Characterization of an Al-Cu-Li-Mg-Ag Alloy