Abstract:We have conducted an experimental study to investigate the synthesis of multi-walled carbon nanotubes (CNTs) in counterflow methane–air diffusion flames, with emphasis on effects of catalyst, temperature, and the air-side strain rate of the flow on CNTs growth. The counterflow flame was formed by fuel (CH4 or CH4+N2) and air streams impinging on each other. Two types of substrates were used to deposit CNTs. Ni-alloy (60% Ni+26% Cr+14% Fe) wire substrates synthesized curved and entangled CNTs, which have both straight and bamboo-like structures; Si-substrates with porous anodic aluminum oxide (AAO) nanotemplates synthesized well-aligned, self-assembled CNTs. These CNTs grown inside nanopores had a uniform geometry with controllable length and diameter. The axial temperature profiles of the flow were measured by a 125μm diameter Pt/10% Rh–Pt thermocouple with a 0.3mm bead junction. It was found that temperature could affect not only the success of CNTs synthesis, but also the morphology of synthesized CNTs. It was also found, against previous general belief, that there was a common temperature region (1023–1073K) in chemical vapor deposition (CVD) and counterflow diffusion flames where CNTs could be produced. CNTs synthesized in counterflow flames were significantly affected by air-side strain rate not through the residence time, but through carbon sources available for CNTs growth. Off-symmetric counterflow flames could synthesize high-quality CNTs because with this configuration carbon sources at the fuel side could easily diffuse across the stagnation surface to support CNTs growth. These results show the feasibility of using counterflow flames to synthesize CNTs for particular applications such as fabricating nanoscale electronic devices.

In-situ filling of Fe/Ni oxide nanowire into carbon nanotubes doped with nitrogen in CH4/H2/air plasmas

<i>In Situ</i> Filling of Fe/Ni Oxide Nanowire into Carbon Nanotubes Doped with Nitrogen in CH<sub>4</sub>/H<sub>2</sub>/Air Plasma

Synthesis of Well-Aligned Multiwalled Carbon Nanotubes on Ni Catalyst Using Radio Frequency Plasma-Enhanced Chemical Vapor Deposition

In situ growth of N-doped carbon nanotubes from the products of graphitic carbon nitride etching by nickel nanoparticles

Fabrication and growth mechanism of Ni-filled carbon nanotubes by the catalytic method

Plasma Composition During Plasma-Enhanced Chemical Vapor Deposition of Carbon Nanotubes

Synthesis and Growth Mechanism of Fe-Catalyzed Carbon Nanotubes by Plasma-Enhanced Chemical Vapor Deposition

Study on the Definite Direction Growth of Carbon Nanotubes by the Microwave Plasma-Enhanced Chemical Vapro Phase Deposition

Optical emission spectroscopy study of the influence of nitrogen on carbon nanotube growth

In-situ Growth of Carbon Nano-tubes/Carbon Nano-fibers(CNTs/CNFs) on the Surface of Carbon Fibers and its Microstructure Investigation

In Situ Synthesis of Iron-Filled Nitrogen-Doped Carbon Nanotubes and Their Magnetic Properties

Synthesis of carbon nanotubes on Ni-alloy and Si-substrates using counterflow methane–air diffusion flames

Effect of Using Chlorine-Containing Precursors in the Synthesis of FeNi-filled Carbon Nanotubes

The Decisive Roles of Chlorine-Contained Precursor and Hydrogen for the Filling Fe Nanowires into Carbon Nanotubes

Nitrogen-doped carbon nanotubes synthesized with carbon nanotubes as catalyst

The Effect of Hydrogen on the Formation of Nitrogen-Doped Carbon Nanotubes Via Catalytic Pyrolysis of Acetonitrile

Flame Synthesis of Carbon Nanotubes with High Density on Stainless Steel Mesh

Tailoring the Structure and Nitrogen Content of Nitrogen-Doped Carbon Nanotubes by Water-Assisted Growth

Densification Kinetics and Mechanical Properties of Carbon/Carbon Composites Reinforced with Carbon Nanotubes Produced in Situ

Long Continuous FeNi Nanowires Inside Carbon Nanotubes: Synthesis, Property and Application

Preparation and Characterization of Ni Nanoparticles Filled Carbon Nanotubes