Potentiometric Hydrogen Sensing of Ultrathin Highly-Ordered SnO2 Films
Hong Zhang,Zhou Li,Jianxin Yi
DOI: https://doi.org/10.1149/ma2020-01282046mtgabs
2020-01-01
ECS Meeting Abstracts
Abstract:Introduction The sensing performance of mixed-potential gas sensors is highly dependent on the electrode microstructure. Recently, much effort has been made to improve the sensor performance by engineering of the electrode microstructure [1, 2]. Nevertheless, the different microstructure parameters, such as thickness, porosity, and three phase boundary (TPB), contribute jointly to the sensing response, and their respective contributions are usually difficult to identify. In order to shed light on the role of TPB, it is crucial to minimize the influence of the diffusion-reaction process occurring inside the electrode, which could be achieved by using a very thin electrode. Moreover, a highly-ordered electrode morphology may help obtain well-defined TPB. Herein, we fabricated sub-micron thick ordered SnO2 sensing electrodes on YSZ substrate by employing a Polystyrene (PS) sphere-template method [3]. Three sensors were obtained by using PS spheres of different diameters in order to vary the TPB density. The gas sensing characteristics of the sensors were systematically studied. The sensing behavior was discussed in relation to the electrode microstructure. Sensor fabrication and characterization As depicted in Figure 1, ultrathin highly-ordered porous film sensors were prepared by using PS sphere templates in 200 nm, 500 nm and 1000 nm diameters. SEM, TEM and AFM images of SnO2 porous film electrodes were presented in Figure 2. Periodically ordered films of inverse opal structure were observed, with uniform circular pore openings and interconnected walls as the skeleton. Each film was porous and a homogenous assembly of 10-20 nm sized particles. The wall height was roughly half of the PS sphere size, which increased from 121 nm to 248 nm and 448 nm for the three PF film electrodes. Sensing performance Figure 3a and b show the response values and response time of the three PF sensors as a function of hydrogen concentration at 500°C. Obviously, the response significantly increased, i.e., became more negative, with decreasing template diameters, while the response time of the three sensors was generally rather close to each other, with a value of 4.5 s-6 s for 500 ppm H2 at 500°C. Figure 3c displays the cross-sensitivities of the PF sensors to 100 ppm various gases at 450°C. The PF sensors exhibited much poorer H2 selectivity than regular thick film sensors [4]. The ultra-small film thickness and porous nature of the PF SE are highly favorable for the gas transport from the gas phase to the TPB. The three PF sensors exhibited very close response time despite their minor difference in the film thickness (in the order of hundreds of nanometer), suggesting absence of significant electrode process and of large H2 concentration reduction. This may allow us to study the effect of the TPB density on the sensing response. The TPB length was thus estimated for the PF sensors. Clearly, the TPB density values increased with the decrease of the PS template diameter. It can also be seen that for each H2 concentration, the response indeed increased (became more negative) monotonically with increasing TPB density (Figure 4). It should be noted, however, that the ultra-thin film electrode was disadvantageous to the selectivity. To achieve good overall sensing performance, e.g., fast response kinetics, large response, and high selectivity, careful tuning of the film thickness and TPB density would be demanded. References [1] N. Miura, T. Sato, S.A. Anggraini, H. Ikeda, S. Zhuiykov, A review of mixed-potential type zirconia-based gas sensors, Ionics. 20(2014) 901-25. doi.org/10.1007/s11581-014-1140-1. [2] G. Lu, Q. Diao, C. Yin, S. Yang, Y. Guan, X. Cheng, et al., High performance mixed-potential type NOx sensor based on stabilized zirconia and oxide electrode, Solid State Ionics. 262(2014) 292-7. doi:10.1016/j.ssi.2014.01.037. [3] L. Jia, W. Cai, H. Wang, Layer-by-layer strategy for the general synthesis of 2D ordered micro/nanostructured porous arrays: structural, morphological and compositional controllability, Journal of Materials Chemistry. 19(2009) 7301-7. doi: 10.1016/j.snb.2011.02.051. [4] J. Yi, H. Zhang, Z. Zhang, D. Chen, Hierarchical porous hollow SnO2 nanofiber sensing electrode for high performance potentiometric H2 sensor, Sensors and Actuators B: Chemical. 268(2018) 456-64. doi.org/10.1016/j.snb.2018.04.086. Figure 1