Abstract:The ultrafine composite fibers based on the composites of binary fatty acid eutectics and polyethylene terephthalate (PET) with varied fatty acid eutectics/PET mass ratios (50/100, 70/100, 100/100 and 120/100) were fabricated using the technique of electrospinning as form-stable phase change materials (PCMs). The five binary fatty acid eutectics including LA-MA, LA-PA, MA-PA, MA-SA and PA-SA were prepared according to Schrader equation, and then were selected as an innovative type of solid-liquid PCMs. The results characterized by differential scanning calorimeter (DSC) indicated that the prepared binary fatty acid eutectics with low phase transition temperatures and high heat enthalpies for climatic requirements were more suitable for applications in building energy storage. The structural morphologies, thermal energy storage and thermal stability properties of the ultrafine composite fibers were investigated by scanning electron microscope (SEM), DSC and thermogravimetric analysis (TGA), respectively. SEM images revealed that the electrospun binary fatty acid eutectics/PET ultrafine composite fibers possessed the wrinkled surfaces morphologies compared with the neat PET fibers with cylindrical shape and smooth surfaces; the grooves or ridges on the corrugated surface of the ultrafine composite fibers became more and more prominent with increasing fatty acid eutectics amount in the composite fibers. The fibers with the low mass ratio maintained good structural morphologies while the quality became worse when the mass ratio is too high (more than 100/100). DSC measurements suggested that the heat enthalpies of melting and crystallization of the ultrafine composite fibers increased gradually with increasing fatty acid eutectics amounts, but their phase transition temperatures had almost no obvious variation as relative to the corresponding fatty acid eutectics. Meanwhile, the characteristic temperatures and heat enthalpies of the ultrafine composite fibers varied with the different types of binary fatty acid eutectics. TGA results indicated that the degradation of electrospun binary fatty acid eutectics/PET ultrafine composite fibers with representative mass ratio of 100/100 had two steps and corresponded respectively to the degradations of binary fatty acid eutectics and PET polymer chains; and the charred residue at 700 degrees C of the composite fibers was lower than that of the neat PET fibers. It could be envisioned that the electrospun binary fatty acid eutectics/PET composite fibers would be extensively used for latent heat storage in the field of building energy conservation. (C) 2012 Elsevier Ltd. All rights reserved.

Preparation, Morphology and Properties of Electrospun Lauric Acid/PET Form-Stable Phase Change Ultrafine Composite Fibres

Morphology and Thermal Properties of Electrospun Fatty Acids/polyethylene Terephthalate Composite Fibers As Novel Form-Stable Phase Change Materials

A novel shape-stabilized PCM: Electrospun ultrafine fibers based on lauric acid/polyethylene terephthalate composite

Preparation, Morphology and Thermal Properties of Electrospun Fatty Acid Eutectics/polyethylene Terephthalate Form-Stable Phase Change Ultrafine Composite Fibers for Thermal Energy Storage

Effects of Nano-Sio2 on Morphology, Thermal Energy Storage, Thermal Stability, and Combustion Properties of Electrospun Lauric Acid/Pet Ultrafine Composite Fibers As Form-Stable Phase Change Materials

Electrospun Ultrafine Composite Fibers Consisting of Lauric Acid and Polyamide 6 As Form-Stable Phase Change Materials for Storage and Retrieval of Solar Thermal Energy

Preparation and Properties of Paraffin /LDPE /OMMT /graphite Phase Change Composite for Thermal Energy Storage

The Improvement Of Thermal Stability And Conductivity Via Incorporation Of Carbon Nanofibers Into Electrospun Ultrafine Composite Fibers Of Lauric Acid/Polyamide 6 Phase Change Materials For Thermal Energy Storage

Ultrafine Lauric–myristic Acid Eutectic/poly (Meta-Phenylene Isophthalamide) Form-Stable Phase Change Fibers for Thermal Energy Storage by Electrospinning

Effects of carbon nanotubes on morphological structure, thermal and flammability properties of electrospun composite fibers consisting of lauric acid and polyamide 6 as thermal energy storage materials

Electrospun Ultrafine Composite Fibers Of Binary Fatty Acid Eutectics And Polyethylene Terephthalate As Innovative Form-Stable Phase Change Materials For Storage And Retrieval Of Thermal Energy

Ultrafine electrospun fibers based on stearyl stearate/polyethylene terephthalate composite as form stable phase change materials

Fabrication and Characterization of Electrospun Fatty Acid Form‐stable Phase Change Materials in the Presence of Copper Nanoparticles

Fabrication, Structural Morphology and Thermal Energy Storage/Retrieval of Ultrafine Phase Change Fibres Consisting of Polyethylene Glycol and Polyamide 6 by Electrospinning

Electrospun phase change fibers based on polyethylene glycol/cellulose acetate blends

Preparation and characterization of lauric acid-stearic acid/fumed silica/expanded graphite thermally conductive enhanced composites

Preparation and Characterization of Lauric Acid/Modified Fly Ash/Graphene Composite as Low-Cost and Eco-Friendly Phase Change Materials for Thermal Energy Storage

Influences of Expanded Graphite on Structural Morphology and Thermal Performance of Composite Phase Change Materials Consisting of Fatty Acid Eutectics and Electrospun PA6 Nanofibrous Mats

Morphology, thermal and mechanical properties of electrospun polyvinylidene/polyethylene glycol composite nanofibers as form-stabilized phase change materials

The Preparation and Characterization of Ultrafine Fatty Acid Ester/Poly( meta -phenylene isophthalamide) Phase Change Fibers Designed for Thermo-regulating Protective Clothing

Preparation and Thermal Properties of Palmitic Acid/expanded Graphite/carbon Fiber Composite Phase Change Materials for Thermal Energy Storage