Abstract:Using wood biomass as opposed to petroleum/fossil feedstock to synthesize chemicals and monomers offers the value proposition of a reduced carbon foot print. A critical step in biomass utilization is to obtain the fermentable monomeric pentose and hexose sugar subunits from various lig-nocellulosic polymers. However, lignin is a three-dimensional amorphous polymer based on methoxylated phenylpropanoid units, and is crosslinks to different polysaccharides with covalent bond. The presence of lignin is a barrier to enzymatic hydrosis of cellulose by cellulases, as well as inhibiting fermentation to form products such as ethanol. Usually, there are three approaches to fractionate biomass into useful chemicals. The first one is extract lignin at high temperature and pressure. The second approach involves more severe conditions such as the temperatures and pressures used in gasification, or use the mineral acids at elevated temperatures to liberate sugars for fermentation. The third way is dissolution of biomass using ionic liquid to extract lignin, and then re-precipitation the cellulosic residue. In this paper, we investigate the lignin extraction uses a purpose designed ionic liquid (IL) 1 -butyl-3-methylimidazolium acesulfamate [BMIM]Ace at room temperature and open atmosphere. It was synthesized from the sugar acesulfamate potassium (Ace K), and with good property of greater thermal stability, increased viscosities, and inability to dissolve crystalline cellulose. In addition, it is of low cost and nontoxic, and is expected to interact with lignin owing to its aromatic character of anion. Organic solvents were firstly used in the extraction process, which reduce the viscosity of IL and increase the lignin yield. The lignin can be obtained by using acetone as the reconstitution solvent (IL/acetone 1:3, v/v), and approximately 11.5% and 96.5% of lignin and the reconstitution cellulose-rich material have been achieved in one dissolution/reconstitution cycle by fresh IL, respectively. It was found that the presence of some organic solvents mix with IL can increase the extraction efficiency. The regenerated ionic liquid showed good retention of structure and properties. The regenerated lignin fractions exhibited large molecular weights (M-w, 3700-7810 g mol(-1)). The physicochemical properties of the extracted lignin fractions were characterized by Fourier transform infrared (FT-IR), and high-performance anion exchange chromatography (HPAEC). The reconstitution cellulose-rich material can be serving as a valuable source for enzymatic saccharification for next step. These results indicate a potential approach in further optimization of the choice of low-cost Its combined with organic solvents for the efficient utilization of the wood biomass.

Composite fibers spun directly from solutions of raw lignocellulosic biomass dissolved in ionic liquids

Rapid Dissolution of Lignocellulosic Biomass in Ionic Liquids Using Temperatures above the Glass Transition of Lignin

Dry-Jet Wet Spinning of Thermally Stable Lignin-Textile Grade Polyacrylonitrile Fibers Regenerated from Chloride-Based Ionic Liquids Compounds

High-performance cellulosic filament fibers prepared via dry-jet wet spinning from ionic liquids

Regeneration of cellulose dissolved in ionic liquid using laser-heated melt-electrospinning

Partial delignification of wood and membrane preparation using a quaternary ammonium ionic liquid

Efficient fabrication of cellulose nanofibers with novel superbase-derived ionic liquid/co-solvents: Rapid cellulose dissolution and improved solution electrospinnability

Extraction Of Lignin From Wood Biomass Using A New Ionic Liquid At Open Atmosphere

Extrusion process to enhance the pretreatment effect of ionic liquid for improving enzymatic hydrolysis of lignocellulosic biomass

Molecularly Engineer Protic Ionic Liquids for Simultaneous Dissolution of Silk Fibroin/Cellulose and Wet-Spinning Composite Fibers Preparation through Hydrogen-Bonding-Acceptor-Strengthening Strategy

The Integration of Different Pretreatments and Ionic Liquid Processing of Eucalyptus: Hemicellulosic Products and Regenerated Cellulose Fibers

Lignin/Poly(vinylpyrrolidone) Multifilament Fibers Dry‐Spun from Water as Carbon Fiber Precursors

Upscaling of lignin precursor melt spinning by bicomponent spinning and its use for carbon fibre production

Regulating Effect of Hemicelluloses on the Preparation and Properties of Composite Lyocell Fibers

Wood Pulping Using Ionic Liquids

Dissolution and delignification of lignin in sugar cane bagasse with ionic liquid EmimAc

Fiber Spinning from Cellulose Solutions in Imidazolium Ionic Liquids: Effects of Natural Antioxidants on Molecular Weight, Dope Discoloration, and Yellowing Behavior

Dissolution of less-processed wood fibers without bleaching in an ionic liquid: Effect of lignin condensation on wood component dissolution

Facile Cellulose Dissolution and Characterization in the Newly Synthesized 1,3-Diallyl-2-ethylimidazolium Acetate Ionic Liquid

Preparation of regenerated cellulose fibers by microfluidic spinning technology using ionic liquids as the solvents

Investigation on spinnability of low molecular weight alkaline lignin to fabricate biobased carbon fiber