Abstract:Sheet metals such as advanced high strength steels often exhibit varying degrees of anisotropy due to the existence of preferred orientation of their grain structures from the rolling process. While extensive research has been devoted to characterize and model anisotropic plasticity behavior over the past decades, only recently people began to tackle their anisotropic fracture behavior. The focus of these studies is almost always on the in-plane anisotropy, and ignores out of-plane fracture behavior. The reasons are two-folds: (1). Sheet metal deformation during a stamping or crash application is mostly thought as in a plane stress state and modeled as such, so there is no need to consider out-of-plane fracture behavior; and (2). It is very challenging to develop experimental techniques to reliably measure out-of-plane fracture strengths for sheet metals with a thickness only about 1 mm. In this paper, we theorize, based on strong empirical evidence, that the fracture strength of a thin sheet metal in out-of-plane shear is inherently weaker than that under in-plane shear, analogous to the interlaminar properties of composite laminates. This weakness is responsible for the so-called "shear fracture" behavior, often observed during the stamping operations of advanced high strength steels when the sheet metal flows around a tight radius. A new double-notched shear specimen with shear plane perpendicular to the thickness direction is carefully designed and tested to accurately measure the out-of plane shear fracture strength. Simulations are executed to validate the rationality of the out-of plane shear specimen design. Test results of a DP980 sheet show that the out-of-plane shear fracture strength is indeed about 15% lower than that measured under the in-plane shear condition. A new anisotropic ductile fracture model based on linear transformation of stresses is proposed to account for the out-of-plane fracture strength for AHSS sheets. The model is calibrated with experimental data, and the fracture surface is compared to the isotropic Mohr Coulomb (M-C) fracture model to illustrate its effectiveness.

Study of toughening mechanisms through the observations of crack propagation in nanostructured and layered metallic sheet

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Mesh Dependence of Transverse Cracking in Laminated Metals with Nanograined Interface Layers

Make Nanostructured Metal Exceptionally Tough by Introducing Non-Localized Fracture Behaviors

Size Effects on the Strengthening/Toughening of Nanostructured Metallic Multilayers

A Nanoindentation Study of the Deformation Mode for Nanostructured Ductile/brittle Multilayers: Cracking Versus Shear Banding

Enhanced strain delocalization through formation of dispersive micro shear bands in laminated Ni

Lamellar Aspect-Ratio and Thickness-Dependent Strength-Ductility Synergy in Pure Nickel During In-Situ Micro-Tensile Loading

Mechanisms of strength and hardening in austenitic stainless 310S steel: Nanoindentation experiments and multiscale modeling

Strengthening and Strain Hardening Mechanisms of a Plain Medium Carbon Steel by Multiscale Lamellar Structures

Toughening by nano-scaled twin boundaries in nanocrystals

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Deformation Behavior and Fracture Mechanism of a Novel Laminated Ni/Al Sheets During In-Situ Tensile Process

Atomistic Insight into Grain Boundary Deformation Induced Strengthening in Layer-Grained Nanocrystalline Al

Anisotropic Fracture of Advanced High Strength Steel Sheets: Experiment and Theory

Enhanced Mechanical Properties and Corrosion Resistance of 316l Stainless Steel by Pre-Forming a Gradient Nanostructured Surface Layer and Annealing

Evaluating the Mechanical Behavior of 316 Stainless Steel at the Microscale Using Finite Element Modelling and In-Situ Neutron Scattering

Activating dispersed strain bands in tensioned nanostructure layer for high ductility: The effects of microstructure inhomogeneity

Pinning cracks by microstructure design in brittle materials

Comparison on crack propagation under tension at 150 °C of Mg-2Zn-1.5Mn alloy sheets with and without crack notch