Abstract:Lightweight hybrid structures of Al MMCs and titanium alloy dissimilar materials have great prospect in the defence industry application. So, it is necessary to join Al MMCs with Ti metal to achieve this structural design. In this work, in-situ TiB2/7050 composite and TA2 were firstly attempted to join by TIG welding-brazing technique. The result was that the intact welding-brazing butt joint was successfully fabricated. The joint presents dual characteristics, being a brazing on TA2 side and a welding on TiB2/7050 side. At brazing joint side, ER4043 filler metal effectively wets on TA2 under TIG heating condition, and a continuous interfacial reaction layer with 1–3 μm is formed at welded metal/TA2 interface. The whole interfacial reaction layers are composed of Ti(AlSi)3 intermetallic compounds (IMCs), but their morphologies at the different regions present obvious distinguishes. The microhardness of the reaction layers is as much as 141–190 HV. At welding joints side, the fusion zone appears the equixaed crystal structure, and the grain sizes are much smaller than those of welded metal, which is attributed to the effect of TiB2 particulates from the melted TiB2/7050 on acceleration formation and inhibiting growth for the new crystal nucleus. The tensile test results show that average tensile strength of the optimal welding-brazing joint is able to achieve 138 MPa. The failure of the tensile joint occurs by quasi-cleavage pattern, and the cracks initiate from the IMCs layer at the groove surface of TA2 and propagate into the welded metal.

Joining Aluminium to Titanium by Mig Welding-Brazing Process

The Microstructure and Mechanical Properties of Fluxless Gas Tungsten Arc Welding–brazing Joints Made Between Titanium and Aluminum Alloys

Cold Metal Transfer Welding-Brazing of Pure Titanium Ta2 to Aluminum Alloy 6061-T6

TIG Welding-Brazing of Ti6Al4V and Al5052 in Overlap Configuration with Assistance of Zinc Foil

Enhanced Interfacial Reaction and Mechanical Properties of Laser Welded-Brazed Mg/Ti Joints with Al Element from Filler

Microstructure and mechanical properties of TIG welded-brazed joint ofdissimilar Al/Ti alloy

Interfacial characteristic and property of Ti/Al dissimilar alloys joint with arc welding-brazing

Welding and Joining of Titanium Aluminides

Dissimilar joining of Titanium alloy to Aluminium using Al-Si based filler alloy by vacuum brazing technique

Study of the Microstructure and Properties of the Butt Joint of Laser-Welded Titanium Alloy with Flux-Cored Wire

Investigation on TIG Arc Welding–brazing of Ti/Al Dissimilar Alloys with Al Based Fillers

Mechanical properties and microstructure analysis of welding-brazing of Al/ti butt joint with Zn foil additive

Aluminum to titanium laser welding-brazing in V-shaped groove

Fabrication and Analysis of TIG Welding-Brazing Butt Joints of In-Situ TiB2/7050 Composite and TA2

Joining Aluminium to Red Copper by High-Frequency Induction Brazing with Argon Shielding

Joining Of Aluminum And Magnesium Via Pre-Roll-Assisted A-Tig Welding With Zn Interlayer

Microstructure and mechanical properties of laser welded-brazed titanium/aluminum joints assisted by titanium mesh interlayer

Effects of Si Additions on Intermetallic Compound Layer of Aluminum–steel TIG Welding–brazing Joint

TIG welding-brazing joints of aluminum-stainless steel with different thickness of base metals

Interfacial structure and properties of reactive brazing joints of TiAl/Ni-based alloy

Interfacial Microstructure and Joining Properties of TiAl/Si3N4 Brazed Joints