Abstract:In this research, a three-dimensional (3D) transient finite element model based on a sequentially coupled thermal–mechanical analysis (SCTMA) is proposed to simulate the evolution of the temperature field and stress field as well as the cladding geometry of the Ni60A-25 % WC laser cladding composite coating. Based on the thermo-physical properties of Ni60A-25 % WC powder and the design of the double ellipsoidal heat source model, a 3D finite element model of double-layer laser cladding with two channels is established. The evolution of the temperature field and the residual stress field at different laser process parameters are investigated to evaluate the quality of the cladding layer. The impact of different laser cladding process parameters on the cladding dimensions is investigated. The dimensions of the simulated molten pool are analyzed by fitting a polynomial curve. The simulation results show that the laser power is proportional to the temperature, and the temperature growth rate of the coating is significantly higher than that of the substrate. The scanning speed is inversely proportional to the temperature. The maximum temperature of the cladding is 1.5 times the maximum temperature of the substrate. The temperature growth rate of the cladding layer is twice that of the substrate. Due to the asymmetry of the heat source in the multi-pass cladding process, the laser energy absorption rate is not the same on both sides of the melted layer. The double ellipsoidal heat source model has a larger diffusion range in the un-melted powder, resulting in asymmetry in the width direction of the cladding layer. The analysis of the residual stresses in the cladding layer shows that the residual compressive stresses in all paths increase with the increasing laser power. The normal x residual compressive stress in the coating and the maximum residual compressive stress occur at the end of the laser beam scan. The residual compressive stress in all paths decreases as the scanning speed increases. The results show that the dimensions of the molten pool are proportional to the laser power and inversely proportional to the scanning speed. The cladding geometry can be calculated with polynomial fitting equations at a selected laser power (500 W–2800 W) and scanning speed (1 mm/s–8 mm/s). The error analysis of the simulation and the experimental results can validate the proposed finite element simulation model. The error in the molten pool size is less than 20 % for the simulation and experimental results.

Laser Cladding of Micro-Fluidic Channel Mold

Temperature Field Simulation and Experimental Analysis of Laser Cladding 45 Steel.

Precision Nd : Yag Laser Cladding with Coaxial Powder Feeding on Very Thin Sheet

Multi-objective Numerical Simulation of Geometrical Characteristics of Laser Cladding of Cobalt-Based Alloy Based on Response Surface Methodology

Study on the Powder Feeding Technique during Laser Micro Cladding Deposition Manufacturing of TC4 Powder

Statistical Analysis of Morphological Characteristics of Inconel 718 Formed by High Deposition Rate and High Laser Power Laser Cladding

Numerical simulation of thermal transfer and flow behavior of Ni60AA formed by laser cladding

Microstructure and Mechanical Properties of Ti-6al-4v Components Fabricated by Laser Micro Cladding Deposition

Design a New Type of Laser Cladding Nozzle and Thermal Fluid Solid Multi-Field Simulation Analysis

Development of microstructure simulation methods of laser cladding layer

Study on the Deformation Control and Microstructures of Thin-Walled Parts Repaired by Laser Cladding

Effect of Cooling Method on Formability of Laser Cladding IN718 Alloy

Evolutionary Mechanism of Solidification Behavior in the Melt Pool during Disk Laser Cladding with 316L Alloy

Quantitative analysis and experimental study of the influence of process parameters on the evolution of laser cladding

Laser Surface Cladding: the State of the Art and Challenges

Numerical simulation and solidification characteristics for laser cladding of Inconel 718

An experimental investigation of micro-channels on transparent material using Nd: YAG laser transmission technique

Modeling for evaluating the effect of powder flow during laser cladding process: From thermal and flow fields to microstructure of the molten pool

Analysis of the sequentially coupled thermal–mechanical and cladding geometry of a Ni60A-25 %WC laser cladding composite coating

Optimization of Process Parameters, Microstructure, and Properties of Laser Cladding Fe-Based Alloy on 42CrMo Steel Roller

Fabricating Inner Channels in Laser Additive Manufacturing Process Via Thin-Plate-Preplacing Method.