Abstract:The macroscopic anisotropics,which are caused primarily by crystallographic textures, have significant effects on the formability of metal sheets and were extensively investigated experimentally and theoretically.Among the numerous theoretical investigations,the phenomenological approach is based on the classical theory of plasticity,in which the plastic behavior of metals is assumed to be well described by analytical functions proposed by Hill,Hosford and Barlat etc..Because of its simplicity, the phenomenological approach is widely used in finite element method for plastic forming analysis, but this method lacks direct connection between textures and the revealed anisotropics.An alternative is the Taylor-Bishop-Hill(TBH) model which adopts the crystal plastic theory and explicitly takes the crystallographic textures into account,and thus can be used to analyze the anisotropic phenomena on a physical basis.However,implementation of the TBH model into the analysis of industrial forming process is a real tedious task,needing large amount of computational skill and computer resources.Besides, the TBH polycrystalline model does not satisfy the stress equilibrium condition between grains. The viscoplastic self-consistent(VPSC) model for polycrystalline is also a crystal plastic scheme,but it satisfies both strain compatibility and stress equilibrium conditions.In this study,mathematical models for the Lankford coefficient(r value),uniaxial tensile yield stress and yield locus were established based on the polycrystalline VPSC scheme.The effects of ideal crystallographic textures on the macroscopic anisotropy of fcc materials were analyzed.The results show that the minimum r values of Cube and Goss textures appear at an angle of about 45°from the rolling direction(RD),the r values of Cube at 0°and 90°are both approximately equal to unity whereas the r value of Goss at 90°is much higher than that of 0°.For the Cu,Bs and S textures,their maximum r values appear at the angle of about 45°from RD,and their r values of 0°and 90°present some asymmetries.The uniaxial tensile yield stresses of these ideal textures exhibit corresponding characteristics to their r values and the shape of yield locus also varies accordingly.The simulation results are in agreement qualitatively with those of TBH model and phenomenological theory.

Mesoscale Simulation of Uniaxial Tension of Fcc Polycrystal Using Viscoplastic Self Consistent Method

Simulation of Texture Evolution During Plastic Deformation of FCC, BCC and HCP Structured Crystals with Crystal Plasticity Based Finite Element Method

A finite strain micromechanical-based constitutive model: Application to porous polycrystal

Meso-scale simulation on mechanical behavior of single crystal titanium

Using Crystal Plasticity Finite Element Method to Investigate the Mechanical Properties under Uniaxial Compression

Modeling Uniaxial Tensile Deformation of Polycrystalline Al Using CPFEM

On plastic anisotropy of constitutive model for rate-dependent single crystal

4223 - ANALYSIS ON CYCLIC PLASTICITY AND STRESS DISTRIBUTION OF POLYCRYSTAL AT GRAIN LEVEL

Investigation on Plastic Flow Behaviors of FCC Polycrystalline Aluminum under Pre-Cyclic Tension-Compression Loading: Experiments and Crystal Plasticity Modeling.

Numerical Simulations of Adiabatic Shear Localization in Textured FCC Metal Based on Crystal Plasticity Finite Element Method

Crystal Plasticity Constitutive Model for BCC Based on the Dislocation Density

An Elasto-Viscoplastic Self-Consistent Model for Polycrystalline Material with Imperfect Interface under Coupled Thermo-Mechanical Loads

Accurate Simulation of Texture Evolution and Mechanical Response of Cubic and Hexagonal Structural Alloys Using Self-Consistent Polycrystal Plastic Method

Modeling on strain softening and Portevin-Le Chatelier effect in crystalline materials based on mesoplasticity

Study of Fcc Metal Tension Behaviour by Crystal Plasticity Finite Element Method

3D Crystal Plasticity Finite Element Modeling of the Tensile Deformation of Polycrystalline Ferritic Stainless Steel

3D modeling of material microstructure and crystal plasticity finite element simulation

Microstructure-based multiscale modeling of large strain plastic deformation by coupling a full-field crystal plasticity-spectral solver with an implicit finite element solver

Modeling of Heterogeneous Tensile Deformation of Polyscrystalline Aluminum

Simulation of Polycrystalline Aluminum Tensile Test with Crystal Plasticity Finite Element Method

Simulation of Effects of Crystallographic Textures on the Macroscopic Anisotropy of Metal Sheet