Abstract:To improve the surface biocompatibility of titanium films, a layer-by-layer (LBL) self-assembly technique, based on the polyelectrolyte-mediated electrostatic adsorption of chitosan (Chi) and gelatin (Gel), was used leading to the formation of multilayers on the titanium thin film surfaces. The film growth was initialized by deposition of one layer of positively charged poly(ethylene imine) (PEI). Then the thin film was formed by the alternate deposition of negatively charged Gel and positively charged Chi utilizing electrostatic interactions. The LBL film growth was monitored by several techniques. The chemical composition, surface topography as well as wettability were investigated by using X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), confocal laser scanning microscopy (CLSM) and water contact angle measurement, respectively. Quantitative XPS analysis showed the alternative change of C/N ratio after four sequential cycles coating of Ti/PEI/Gel/Chi/Gel, which indicated the discrete layer structure of coatings. Uncoated titanium (control sample) displayed a smooth surface morphology (root mean square (RMS) roughness was around 2.5nm). A full coverage of coating with Gel/Chi layers was achieved on the titanium surface only after the deposition layers of PEI/(Gel/Chi)2. The PEI/Gel/(Chi/Gel)3 layer displayed a rough surface morphology with a tree-like structure (RMS roughness is around 82nm). These results showed that titanium films could be modified with Chi/Gel which may affect the biocompatibility of the modified titanium films. To confirm this hypothesis, cell proliferation and cell viability of osteoblasts on LBL-modified titanium films as well as control samples were investigated in vitro. The proliferation of osteoblasts on modified titanium films was found to be greater than that on control (p<0.05) after 1 and 7 days culture, respectively. Cell viability measurement showed that the Chi/Gel-modified films have higher cell viability (p<0.05) than the control. These data suggest that Chi/Gel were successfully employed to surface engineer titanium via LBL technique, and enhanced its cell biocompatibility. The approach presented here may be exploited for fabrication of titanium-based implant surfaces.

Surface Modification of Titanium by Using Plasma‐induced Graft‐polymerization

Fabrication and in vitro evaluation of the collagen/hyaluronic acid PEM coating crosslinked with functionalized RGD peptide on titanium.

Effects of Plasma Polymerization on the Performance of Biomedical Titanium

A bioactive polymer grafted on titanium oxide layer obtained by electrochemical oxidation. Improvement of cell response

Oxygen Plasma Ion Implantation of Biomedical Titanium Alloy

Surface Bioactivity Modification of Titanium by CO2 Plasma Treatment and Induction of Hydroxyapatite: in Vitro and in Vivo Studies

Single-step amphoteric surface modification through plasma polymerization: Antifouling coating for titanium substrate

Non-thermal atmospheric pressure plasma treatment increases hydrophilicity and promotes cell growth on titanium alloys in vitro

Improvement of Surface Bioactivity on Titanium by Water and Hydrogen Plasma Immersion Ion Implantation

Surface Modification of Titanium with Hydroxyapatite Layer Induced by Phase-Transited Lysozyme Coating

Influence of Hybrid Surface Modification on Biocompatibility and Physicochemical Properties of Ti-6Al-4V ELI Titanium

Functionalization of Titanium Surfaces Via Controlled Living Radical Polymerization: from Antibacterial Surface to Surface for Osteoblast Adhesion

Porous structure preparation and wettability control on titanium implant

Fabrication and evaluation of porous coatings doped with bioactive elements on titanium surfaces

Enhanced antioxidant capability and osteogenic property of medical titanium by cerium plasma immersion ion implantation

Modification of titanium surfaces via surface-initiated atom transfer radical polymerization to graft PEG-RGD polymer brushes to inhibit bacterial adhesion and promote osteoblast cell attachment

Fabrication of Cationic Polymer Surface Through Plasma Polymerization and Layer-by-layer Assembly

Preparation and Bioactive Response of Super-Hydrophilic Surface on Selective Laser Melting Titanium

Polysaccharide-protein surface modification of titanium via a layer-by-layer technique: characterization and cell behaviour aspects.

A Facile Technique for Fabricating Poly (2-Methacryloyloxyethyl Phosphorylcholine) Coatings on Titanium Alloys

Influence of micro and nanoporous TiO 2 surface modifications on physical-chemical and biological interactions