Abstract:The prospect of joining titanium and aluminum components into structures is desirable for a wide range of aerospace and automobile industry applications. One of the problems related with the joining processes for dissimilar metals such as Ti and Al is the formation of residual stress in the bonded joint, which has significant effect on the joint mechanical properties. In this work, joining of a titanium alloy to an aluminum alloy by ultrasonic assisted brazing using a Zn-Al filler metal was investigated. The microstructures of the titanium/aluminum brazed joints were determined by OM, SEM and TEM. The local tensile deformation characteristics of the brazed joints were also examined using the digital image correlation (DIC) methodology by mapping the local strain distribution during in situ tensile tests. The results showed that the Ti7Al5Si12 phase and the TiAl3 phase were formed at the titanium/brazing seam interface. The brazing seam was primarily composed of a Zn-rich phase and a Zn-24.14% Al (mass fraction) eutectoid structure. At the aluminum/brazing seam interface, no interfacial reaction layer was observed and the primary phase Zn-Al dendrites nucleated at the aluminum base metal and grew into the inside of the bonding region. A diffusion layer was formed in the aluminum base metal. It was found that the tensile deformation of the brazed joints was highly heterogeneous, which led to the deflection of the crack during propagating in the joint. The fracture initiated at the Zn-rich phases, where contained the highest stress concentration due to their low elastic modulus, and propagated in the Zn-rich phases or through the interface between Zn-rich phase and Zn-Al eu-tectoid structure.

Interfacial reaction of intermetallic compounds of ultrasonic-assisted brazed joints between dissimilar alloys of Ti-6Al-4V and Al-4Cu-1Mg

Interfacial Microstructure and Mechanical Properties of Ultrasonic-Assisted Brazing Joints Between Ti–6Al–4V and ZrO2

Microstructure and Mechanical Properties of Ti–6Al–4V/Al1060 Joints by Ultrasonic-Assisted Brazing in Air

Influence of Si content on interfacial reactions and mechanical properties of dual-spot laser welded-brazed Ti/Al joints

Interfacial Microstructure and Mechanical Properties of Induction Brazing TiAl/40Cr Joints

Ultrasound-assisted Brazing of Cu/Al Dissimilar Metals Using a Zn–3Al Filler Metal

Interaction Behaviors at the Interface Between Liquid Al–Si and Solid Ti–6Al–4V in Ultrasonic-Assisted Brazing in Air

Microstructure and Mechanical Properties of Ultrasonically Assisted Brazing of Dissimilar Cu–Al Alloys

Research on the Interfacial Structure and Properties of TiAl - Si3N4f/Si3N4 Brazed Joints

Interfacial features of TiAl alloy/316L stainless steel joint brazed with Zr−Cu−Ni−Al amorphous filler metal

Ultrasonic-assisted Brazing of SiC Ceramic to Ti–6Al–4V Alloy Using a Novel AlSnSiZnMg Filler Metal

Acoustic cavitation-induced microstructure evolution in ultrasonically brazed Al/Cu joints using Zn-Al alloy fillers

Strain Field and Fracture Behavior of Ti/Al Dissimilar Alloy Joint under in Situ Tensile Test

Study on Interfacial Reaction Behavior and Properties of Al/Zn-3Al/Cu Fluxless Brazed Joint

Formation of Amorphous Interfacial Layer Between Zn-based Alloy and SiC Particles under Ultrasonic-Assisted Brazing

Interfacial Microstructure and Phase Constitution of the Cu/Al Dissimilar Metals Joint Made by Contact Reactive Brazing

Interfacial Microstructure and Mechanical Property of ZrC-SiC Ceramic and Ti6Al4V Joint Brazed with AgCuTi Alloy

Interfacial microstructure and properties of TiAl joints brazed with composite filler reinforced by particles

Ultrasonic-assisted Brazing of Al–Ti Dissimilar Alloy by a Filler Metal with a Large Semi-Solid Temperature Range

Interfacial Structure and Strength of Al‐25Si‐4Mg‐1Cu Joint Brazed with Zn Interlayer

Interfacial microstructure and properties of brazing joints of TiAl/Ni-based alloy